1. Introduction
The XTOOL D5S is an essential diagnostic tool designed to address common automotive issues across various systems including engine, transmission, ABS, EPB, and SRS. This advanced diagnostic device efficiently identifies and clears fault codes, accesses data stream information, reads freeze frame data, and retrieves ECU information.
The D5S features an upgraded dual-core 1.2GHz Processor, 128MB RAM, and 32GB ROM, operating on a user-friendly Linux system. It is powered by a robust 3150mAh 3.6V battery for extended use.
It offers 19 special functions, all with lifetime free updates, such as Oil Light Reset, EPB, SAS, DPF, BMS Reset, Throttle, TPMS Reset, ABS Bleeding, Injector Coding, Gearbox Matching, Suspension, Window Initialization, Headlight, EGR Relearn, Control Unit Reset, and Gearbox Matching. Additionally, the D5S allows users to view up to four data streams simultaneously in a single interface.
2. Safety Information
2.1 Legal Information
Trademarks: XTOOL is a registered trademark of Shenzhen XTOOL Technology Co., Ltd. All other trademarks mentioned are the property of their respective owners.
Copyright Information: No part of this manual may be reproduced or transmitted without prior written permission from XTOOL. ©2010 Shenzhen XTOOL Technology Co., Ltd. All rights reserved.
Disclaimer of Warranties and Limitation of Liabilities: The information, specifications, and illustrations in this manual are for reference only and may change without notice. XTOOL is not responsible for direct, special, incidental, or indirect damages, including economic losses. XTOOL reserves the right to make changes without prior notice.
2.2 General Safety Instructions
Before using or maintaining this unit, thoroughly read this manual and pay close attention to the safety warnings and precautions provided.
- Read and Understand: Ensure all operators and individuals near the device have read and understood the safety instructions.
- Proper Use: Only use the device as described in this manual. Always adhere to safety messages and test procedures from the vehicle or equipment manufacturer.
2.3 Specific Responsibilities
- Refer to Manufacturer Guidelines: Always consult and follow safety messages and test procedures from the vehicle or equipment manufacturer.
- Use Appropriate Tools and Techniques: Use correct tools and techniques for each specific task, considering product variations.
- Anticipate Safety Requirements: Be prepared to handle unforeseen circumstances safely.
2.4 Safety Messages
Safety messages are included to prevent personal injury and equipment damage. Each message begins with a signal word indicating the hazard level:
Danger
This indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Warning
This indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
2.5 Safety Instructions for Operation
- Safe Environment: Always perform automotive testing in a safe environment.
- Eye Protection: Wear safety eye protection that meets ANSI standards.
- Avoid Hazards: Keep clothing, hair, hands, tools, and test equipment away from all moving or hot engine parts.
- Ventilation: Operate the vehicle in a well-ventilated work area to avoid inhaling poisonous exhaust gases.
- Transmission and Brakes: Put the transmission in PARK (automatic) or NEUTRAL (manual) and engage the parking brake.
- Wheel Blocks: Place blocks in front of the drive wheels and never leave the vehicle unattended while testing.
- Ignition System Caution: Be extra cautious around the ignition coil, distributor cap, ignition wires, and spark plugs, as these components generate hazardous voltages when the engine is running.
- Fire Extinguisher: Keep a fire extinguisher suitable for gasoline, chemical, and electrical fires nearby.
- Test Equipment Connections: Do not connect or disconnect any test equipment while the ignition is on or the engine is running.
- Clean Equipment: Keep the test equipment dry, clean, and free from oil, water, or grease. Use a mild detergent on a clean cloth to clean the outside of the equipment as necessary.
- No Driving While Testing: Do not drive the vehicle and operate the test equipment simultaneously to avoid distractions.
- Service Manual Reference: Refer to the vehicle's service manual and adhere to all diagnostic procedures and precautions.
- Battery Check: Ensure the vehicle battery is fully charged and the connection to the vehicle DLC is clean and secure.
- Avoid Electromagnetic Interference: Do not place the test device on the vehicle's distributor, as strong electromagnetic interference can damage the device.
3. Product Overview
3.1 Main Ports of The Tablet

The XTOOL D5S tablet features the following main components:
- 5.45-inch Touch Screen
- Power Button
- VGA 15 PIN-Port
- Type-C Port
- Memory Card Slot (Expandable up to 128GB)
3.2 What's In The Box
The XTOOL D5S package typically includes the following items:
| Item | Quantity |
|---|---|
| Tablet | 1 |
| VAG to OBD-II-16 Main Cable | 1 |
| Quick Guide | 1 |
| Packing List | 1 |
| Color Carton | 1 |
| USB Type-C Main Cable | 1 |
4. Setup
4.1 Power Sources
The XTOOL D5S Diagnostic Tool can be powered by one of three methods:
- Internal Battery Pack: A fully charged internal rechargeable battery provides approximately 3.5 hours of continuous operation. If completely drained, charge for more than 6 hours before turning on.
- AC Power Supply: Connect the Diagnostic Tool to a standard AC outlet using the provided AC power supply. Ensure the output cable is plugged into the DC power supply input jack on the tablet.
- 12-Volt Vehicle Power: Locate the vehicle's OBDII port (typically under the driver's seat or near the steering wheel). Insert the 16-pin connector of the OBDII cable into the vehicle's port, and connect the 15-pin end to the Diagnostic Tool, tightening the nut for a secure connection.
4.2 Turning On/Off and Emergency Shutdown
- Turning On: Press and hold the power button (top right) for approximately five seconds. The tool will power on if the battery has sufficient charge or if connected to AC power.
- Turning Off: Press and hold the power button for more than three seconds. Ensure all vehicle communications are terminated before powering off to avoid potential issues with the ECM.
- Emergency Shutdown: Only use if the tool is unresponsive. Press and hold the power button for at least five seconds. Note that forcing a shutdown during communication with the vehicle ECM may cause issues.
4.3 Wi-Fi Connection
The Diagnostic Tool can connect to 2.4 GHz or 5.0 GHz Wi-Fi or a mobile hotspot.
- Navigate to More > Settings > Wi-Fi connection.
- Switch on Wi-Fi connection and select your desired network, then enter the password.
How to turn on a mobile hotspot:
- For iOS users: Go to Settings > Turn on cellular network > Personal Hotspot. Switch on "Allow Others to Join" and "Maximize Compatibility."
- For Android users: Go to Settings > Wireless & networks > Tethering & portable hotspot > Portable WLAN hotspot. Switch on hotspot and configure WLAN hotspot with WPA2 PSK encryption. Ensure "Max connections allowed" has available slots.
Note:
A Wi-Fi connection is not always necessary for diagnostics, but for certain brands (e.g., Peugeot) requiring online server access, it is essential.
4.4 Product Activation
To activate your device:
- Select an available Wi-Fi network.
- For first-time users, the system will guide you to enter a valid email address and set a login password. Click "Register." If already registered, click "Log in."
- Click "Start to use" to enter the diagnostic system.
Password Reset: If you forget your password, go to More menu > Profile > Account Information > New password to modify it. You will receive a verification code via email.
Delete Activation Information: To log in with a different account, go to More menu > Profile > Account Information > Exit current account, then click OK. This returns you to the initial registration page where you can create a new account or log in to an existing one.
4.5 Vehicle Connection

The scan tool must be connected to the vehicle's OBD-II port to establish communication.
- Turn on the tablet.
- Connect the vehicle and tablet using the main test cable (VGA to OBDII-16 Main Cable).
- Turn on the vehicle's ignition switch to start the diagnostic process.
Note:
If the OBD port is hard-to-reach, an OBD extension cable may be purchased for easier operation.
5. Operating Instructions
5.1 Screen Layout & Screen Icons

When the Diagnostic Tool is turned on, the main diagnostic screen will appear with the following icons:
- Auto Scan: Automatically detects and decodes the VIN, then scans all available vehicle electronic control modules for diagnostics.
- Diagnosis: Accesses the diagnostic menu, allowing automatic VIN detection or manual input of vehicle information (make, model, year) for diagnostics.
- OBD-II: Provides standard OBD-II functions including reading/clearing fault codes, monitoring real-time data, and detecting emission system issues.
- Special Functions: Accesses commonly performed maintenance services.
- Updates: Allows downloading diagnostic software programs individually or in batches.
- More: Provides access to user account/workshop profile setup, firmware information, diagnostic reports, language settings, measurement units, etc.
5.2 How to Diagnose Vehicles
The Diagnostic Tool enables communication with a vehicle's electronic control systems to retrieve DTCs, view PID data, and perform advanced functions.
- My Vehicles: Add frequently used diagnostic programs for quick access.
- Compatibility Check: This tool is compatible with all OBD-II/EOBD vehicles for generic tests and a wide range of makes/models for comprehensive diagnostics. Specific function availability varies by vehicle. Consult www.xtoolonline.com/support/vehicle-coverage or contact support for verification.
- Software Program Version: Displays the current software version at the bottom of each vehicle manufacturer's screen.
- Vehicle Voltage Display: The screen displays the real-time voltage of the vehicle's battery, allowing monitoring during use.
- Demo Program: Simulates vehicle navigation and function options for training purposes.
5.2.1 Vehicle Identification
To ensure proper communication, the vehicle must be correctly identified. Follow screen prompts to enter required information.

Auto VIN & Auto Scan - Four Ways:
- Auto Scan (Auto Identification): Click the "Auto Scan" icon to automatically scan and decode the vehicle's VIN.
- Manual Input VIN: If auto scan fails, manually input the VIN.
- Automatic Detection: In the "Diagnosis" menu, select region, brand, and then "Automatic Detection."
- Manual Selection: The most reliable option. In the "Diagnosis" menu, select region, brand, "Manual Selection," model year, and other configurations.
Note:
Auto Identification may not be compatible with all vehicles. If it fails, try manual options. If the VIN is not in the ECU or database, manual selection is necessary.
5.2.2 Diagnostics Process
- Automatic Scan: Scans available vehicle modules for diagnostics.
- System Selection: After identifying potential issues, select an individual vehicle module for targeted troubleshooting.
5.3 OBD-II/EOBD Functions
This section covers the concept, protocols, test functions, and basic operation of the OBD-II/EOBD function, primarily for emission-related diagnostics.
- OBD-II Protocols: Supports SAE J1850PWM, SAEJ1850VPW, ISO 9141-2, ISO 14230-4, ISO 15765-4.
- Help: Provides information on DLC location, DTC library, abbreviations, and OBD background.
- 10 Modes of OBD-II: Mode $01 - Live Data, Mode $02 - Read Freeze Frame, Mode $03 - Read Trouble Code, Mode $04 - Clear Trouble Code, Mode $05 - O₂S Monitoring Test, Mode $06 - On-Board Monitor Test, Mode $07 - Read Trouble Code, Mode $08 - Component Test, Mode $09 - Read ECU Information, Mode $0A - Read Trouble Code.
- Connecting the Main Cable: The main cable must be connected to both the Diagnostic Tool and the vehicle's OBD-II port for OBD-II testing.
5.3.1 Read Trouble Code
Displays current emission-related DTCs, including Stored Codes, Pending Codes, and Permanent Codes. OBD-II codes are prioritized by emission severity.
- Stored Codes: Current emission-related DTCs from the ECM. Priority determines MIL illumination and code erase procedure.
- Pending Codes: Maturing DTCs whose conditions were met but require multiple drive cycles to set. Useful for verifying repairs after a single drive cycle.
- Permanent Codes: DTCs severe enough to illuminate the MIL, even if the MIL is off. These clear automatically after repairs and successful system monitor runs.
5.3.2 Clear Trouble Code (Mode $04)
Erases all emission-related diagnostic data (DTCs, freeze frame data, test results) from the ECM. A confirmation screen appears to prevent accidental data loss. Some faults may reappear if the underlying issue is not resolved.
5.3.3 Live Data (Mode $01)
Views current emission-related data from the selected ECM. Displays parameter descriptions and values with units.
- View Waveform Chart: Click the circled area in the diagram to view the waveform chart for each data stream.
- Select Live Data: Click "Show Selected" to display only chosen data streams. You can select up to four data streams at a time.
- 4-IN-1 Live Data: Select data streams and click "Curve Combinator" for a combined graphical data stream.

Description: This image illustrates the 4-in-1 live data graphing capability of the XTOOL D5S, showing how multiple sensor readings can be displayed simultaneously for comprehensive analysis.
5.3.4 Read Freeze Frame (Mode $02)
Displays a snapshot of critical parameter values at the moment a DTC is set, used to analyze the root cause of faults. Freeze frame data varies by vehicle, and some vehicles may not support this function.
5.3.5 I/M Readiness (Smog Check)
Checks the readiness of the monitoring system, useful before emissions inspections. Offers two choices: "Monitor status since DTCs cleared" and "Monitor status this driving cycle."
5.3.6 O₂S Monitoring Test (Mode $05)
Opens a menu of tests for oxygen sensors. Displays pertinent O₂S parameters for each test.
5.3.7 On-Board Monitor Test (Mode $06)
Views results of On-Board Monitor tests, useful after servicing or clearing ECM memory. Data pertains to continuously and intermittently monitored systems.
5.3.8 Component Test (Mode $08)
Enables bidirectional control of the ECM to test components like EVAP leakage. Useful for determining ECM response to commands.
5.3.9 Read ECU Information (Mode $09)
Displays names of ECUs, supported protocols, and calibration information.
5.4 Special Functions
This section details various scheduled services and maintenance functions. Follow on-screen instructions to select options, enter values, and perform necessary actions.

Description: This image highlights the 16 hot maintenance services offered by the XTOOL D5S, providing a visual overview of its extensive capabilities for vehicle upkeep.
- Oil Reset: Resets the engine oil life system after an oil change.
- EPB (Electronic Parking Brake) Reset: Initializes or resets the EPB system after brake pad replacement or repairs.
- Electronic Steering Adaptation (SAS): Re-adapts or calibrates the electronic power steering system after component replacement or adjustments.
- DPF/GPF After-Treatment: Performs operations on Diesel Particulate Filters or Gasoline Particulate Filters, including clearing warnings or regeneration.
- Battery Adaptation (BMS Reset): Reconfigures the battery management system after battery replacement to optimize charging and discharging.
- Throttle Adaptation: Recalibrates the throttle control system after replacing the throttle valve or related components.
- Tire Pressure Reset (TPMS Reset): Resets the Tire Pressure Monitoring System after tire pressure checks or adjustments.
- ABS Auto Bleeding: Automatically bleeds the ABS system after repairing or replacing brake system components to remove air.
- Injector Coding: Codes or calibrates new injectors after replacement to optimize fuel injection.
- Gearbox Matching: Rematches the vehicle's ECU and gearbox after replacement or overhaul.
- Suspension System: Adjusts the vehicle body height sensor for level calibration after replacing suspension components or power interruption.
- Window Initialization: Recalibrates window travel after replacing the window motor or losing power.
- Headlight Adjustment: Recalibrates the angle and range of adaptive headlights after repair or replacement.
- EGR Learning: Re-adjusts the opening and closing timing of the EGR valve after replacement or cleaning.
- Gear Information Learning: Recalibrates gear ratio and speed signals between engine and gearbox sensors.
- Control Unit Reset: Restores ECU parameters to factory default settings after repairs.
5.5 Diagnostic Report
After completing diagnostics, you can generate a detailed diagnostic report by entering VIN, mileage, and model year. Reports can be reviewed, shared via email, or printed.

Description: This image illustrates the process of generating, sharing, and printing diagnostic reports from the XTOOL D5S, allowing users to document and communicate vehicle issues effectively.
5.6 Exiting Diagnostics
To exit tests and turn off the Diagnostic Tool, you must first interrupt the communication link with the vehicle. Exiting diagnostic programs and returning to the main screen will end the diagnosis. Do not disconnect the VGA to OBDII-16 main cable while the tool is actively communicating with the vehicle ECM to avoid potential damage.
6. Maintenance
6.1 Software Updates
Software updates can be performed via Wi-Fi or mobile hotspot. If a "Network abnormal" prompt appears, try another Wi-Fi network or contact support.

Description: This image highlights the XTOOL D5S's lifetime free software updates via Wi-Fi, ensuring the device remains current with the latest vehicle data and functionalities.
You have two options for updating software:
- Update All Software Programs: Click "Update" on the left of the update menu.
- Update Individual Software Program: Click the "↓" icon next to the corresponding software program. If interrupted, click "↓" again.
Delete Software Program: To free up space, enter the Diagnostic menu, long-press a software package, check the box, and click "Delete."
6.2 Data Logging
For software-related issues, data logging provides crucial information for technical support. Ensure your Diagnostic Tool is connected to Wi-Fi for at least 15 minutes and provide the Serial Number (S/N) to the support team.
6.3 Cleaning
Keep the test equipment dry, clean, and free from oil, water, or grease. Use a mild detergent on a clean cloth to clean the outside of the equipment as necessary.
7. Troubleshooting (FAQ)
Here are some common questions and their solutions:
- Q1: I haven't found I/M readiness in the menu.
A: Click the "OBD-II" icon > Auto Scan/Select OBD-II Protocol > I/M Readiness. - Q2: Unable to find live sensor data as the generic OBD2 scanner, like short-term/long-term fuel trim.
A: Click the "OBD-II" icon > Auto Scan/Select OBD-II Protocol > Live Data > LTFT, STFT or similar term. - Q3: Unable to find the misfire data for my Ford/Dodge/Chrysler/Jeep cars?
A: OBD-II > Auto Scan or Select OBD-II Protocol for your car > On Board Monitor Test > Select "Misfire Cylinder Data" or similar term. - Q4: I can not charge the battery now. I plugged in the cord, it's not charging. The battery is almost dead, only about 10% left.
A: 1. Try using the original charging cable or OBD test cable to charge for more than six hours. 2. Hold down the shutdown button for 15 seconds (without charging cable) to see if it turns on. 3. Connect to a computer via USB to see if it's recognized. 4. If issues persist, contact technical support with a video of the charging issue. - Q5: Can scanner tune up car?
A: No, the D5S Diagnostic Tool does not have the capability to tune up a car. - Q6: It was frozen until the battery went flat even I tried the reset button and the power button.
A: Ensure the App is updated to the latest version (More > Setting > About > Version). If updated, reset to factory settings. If the problem persists, contact support. - Q7: I cannot update, I've tried Wi-Fi and cell phone as hotpot, however, keep telling me failure connection.
A: This could be due to router firewall settings or network provider restrictions. Check if your router firewall can access the server. If the problem persists, contact support. - Q8: Why should I connect the scanner to internet once a month?
A: It's a government policy compliant requirement to report IP location to prevent illegal activities. If Wi-Fi connection doesn't resolve the issue, contact support. - Q9: The auto scan/VIN cannot work on my vehicle.
A: Auto scan/VIN does not cover all vehicles (some don't store VIN in ECU, some VINs are not in the database, or vehicles like Dodge use specific communication modes). Try alternative navigation methods: turn on ignition (and engine for older vehicles) for auto scan, manual VIN input, or manual selection via Diagnosis menu. - Q10: My diagnostic tool cannot connect to Wi-Fi.
A: If it shows "times out," check your router for WPA2 (not WPA3) and ensure it's not blocking outgoing network traffic. Using a mobile hotspot often resolves registration issues. If connected but shows "connect internet to sync your device," correct the time zone in Android settings (More menu > Settings > Date & Time). - Q11: When activating the device, shows error message "registration failure" after entering your email address.
A: Try a mobile hotspot (recommended) or a different network to activate. - Q12: Received a used device with a lock screen password, unable to open the device.
A: Contact support with the device's S/N to resolve the issue. - Q13: Shall I connect my device to the Internet/ Wi-Fi all the time?
A: No, not all the time. Internet is needed for registration and downloading updates. Some special vehicles (e.g., Peugeot) and advanced features like ECU Programming require an internet connection. - Q14: Does your tools can support all the functions on all vehicles?
A: Our tools are comprehensive but cannot perform all functions on all vehicles, as vehicle configurations vary.
8. Specifications
| Item | Description/Specification |
|---|---|
| Operating System | Linux |
| Protocols Supported | CAN FD/FCA |
| Processor | Dual-core 1.2GHz |
| Memory | 128M+32G |
| Connectivity | Type-C |
| Operating Method | Flat Panel Touchscreen |
| Upgrade Method | Device Connects to Wi-Fi for Online Upgrade |
| Battery | 3150mAh 3.6V |
| Wi-Fi | 2.4G/5Ghz |
| Tested Battery Life | 3.5 Hours |
| Dimensions | 19.5*2.8*11.5(CM) |
| Free Renewal Update | Lifetime |
| Charging Method | Type-C Charging (No charger included) |
| Sensor | Gravity/ Light Sensor |
| Audio | Microphone |
| Speaker | Built-In Speaker |
| Weight (Including Battery) | 0.4KG |
| Gross Weight | 0.8KG |
| Operating Temp Range (Ambient) | -4°F ~ 140°F (-20°C ~ 60°C) |
| Storage Temp (Ambient) | -40~158°F (-40~70°C) |
| Operating Humidity | <90% |
9. User Tips
- Always ensure a stable Wi-Fi connection for software updates and for diagnostic functions that require online server access.
- Keep your device adequately charged, especially before starting any diagnostic or maintenance procedures, to avoid interruptions.
- If the automatic VIN detection fails, always try manual VIN input or manual vehicle selection to ensure accurate diagnostics.
- For specific vehicle functions or compatibility questions, it's recommended to consult XTOOL's technical support or their official website for the most up-to-date information.
- Regularly check for software updates to ensure your device has the latest vehicle coverage and features.
10. Compliance Information
10.1 FCC Compliance / FCC ID: 2AW3IF510
This device complies with Part 15 of the FCC rules and Industry Canada's license-exempt RSSs. Operation is subject to two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.
WARNING: Unauthorized changes or modifications may revoke the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. It emits radio frequency energy that can potentially interfere with radio communications. Measures to mitigate interference include reorienting/relocating the receiving antenna, increasing separation between equipment and receiver, connecting to a different circuit, or consulting a technician.
10.2 UKCA
The UKCA (UK Conformity Assessed) mark signifies compliance with UK safety and environmental standards for products sold in the UK market, replacing the CE mark post-Brexit.
10.3 RF Warning Statement
The device has been evaluated to meet general RF exposure requirements and can be used in portable exposure conditions without restriction. The term "IC" before the radio certification number signifies that IC technical specifications were met.
10.4 ROHS Compliance
This device complies with the European RoHS Directive 2011/65/EU, restricting hazardous substances in electrical and electronic equipment.
10.5 CE Compliance
This product conforms to the essential requirements of the EMC Directive 2014/30/EU, R&TTE Directive 1999/5/EC, and Low Voltage Directive 2014/35/EU, bearing the CE mark accordingly.
10.6 ISED
ISED (Innovation, Science and Economic Development Canada) is a Canadian government department focused on promoting innovation, scientific research, and economic growth. It develops and implements policies to support businesses, encourages entrepreneurship, facilitates international trade, and regulates areas such as telecommunications and consumer protection. ISED aims to enhance Canada's economic competitiveness and foster a culture of innovation.
11. Warranty & Support
11.1 Limited Two-Year Warranty
Shenzhen XTOOL Technology Co., LTD. warrants to the original retail purchaser that this XTOOL device will be free from defects in material or workmanship for two years from the date of purchase. Defective parts will be repaired or replaced (with new or rebuilt parts) at the Company's option, without charge for parts or labor, upon proof of purchase.
The Company is not liable for incidental or consequential damages arising from the use, misuse, or mounting of the device.
This warranty does not apply to:
- Products subjected to abnormal use or conditions, accident, mishandling, neglect, unauthorized alteration, misuse, improper installation/repair, or improper storage.
- Products with removed, altered, or defaced mechanical or electronic serial numbers.
- Damage from exposure to excessive temperature or extreme environmental conditions.
- Damage resulting from connection to, or use of any unauthorized accessory or product.
- Defects in appearance, cosmetic, decorative, or structural items such as framing and non-operating parts.
- Products damaged from external causes such as fire, dirt, sand, battery leakage, blown fuse, theft, or improper usage of any electrical source.
11.2 Contact Us
For technical assistance, warranty claims, or general inquiries, please use the following contact information:
- Website: https://www.xtoolonline.com/
- Email: support@xtoolonline.com
- Corporate & Business Inquiries: business@xtoolonline.com, sales@xtoolonline.com
You can also join their community for tutorials and support by searching for "xtoolonline" on Facebook, Instagram, TikTok, and YouTube.
User Manual PDF: For a detailed user manual, you can refer to the PDF document available at this link.