Digital Dashboard Cluster User Manual

1. Introduction

This manual provides comprehensive instructions for the installation, operation, and maintenance of your new Digital Dashboard Cluster. This advanced instrument panel is designed to upgrade your vehicle's interior with a high-resolution digital display, offering enhanced functionality and a modern aesthetic. Please read this manual thoroughly before installation and use to ensure proper operation and safety.

For a detailed PDF version of this manual, please refer to the User Manual (PDF).

2. Safety Precautions

• Installation or servicing of this product by persons without training and experience in electronic equipment and automotive accessories may be dangerous and could expose you to the risk of electric shock, injury or other hazards.
• Do not allow this product to come into contact with liquids. Electrical shock could result. Also, damage to the product, smoke, and overheating could result from contact with liquids.
• If liquid or foreign matter should get inside this product, park your vehicle in a safe place, turn the ignition switch off (ACC OFF) immediately and consult your dealer or the customer service. Do not use this product in this condition because doing so may result in a fire, electric shock, or other failure.
• If you notice smoke, a strange noise or odor from this product, or any other abnormal signs on the LCD screen, turn off the power immediately and consult your dealer or the customer service. Using this product in this condition may result in permanent damage to the system.
• Do not disassemble or modify this product, as there are high-voltage components inside which may cause an electric shock. Be sure to consult your dealer or the customer service for internal inspection, adjustments or repairs.
• Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product, and to protect it from overheating. To prevent fire hazard, the openings should never be blocked or covered with items (such as papers, floor mat, cloths).
• Please turn off the car and disconnect ACC from B+ before installation for avoiding short circuit.
• Please insulate the power output wire for avoiding boot failure caused by short circuit.
• Please do not use the car audio for a long time after turning off the engine, or it will exhaust the battery power.
• Never set the volume of this product so high that you cannot hear outside traffic and emergency vehicles.
• Keep this manual handy as a reference for operating procedures and safety information.

3. Product Overview

The Digital Dashboard Cluster features a Linux operating system, a T5 1.5Ghz CPU, and a 1920x720 HD IPS anti-glare screen. It supports various original vehicle information displays and offers multiple UI themes and customization options.

Interfaces and Accessories

• Original vehicle instrument power line interface: For connecting to the vehicle's power system.
• USB interface: For upgrading instruments.
• Reserved dual screen interaction: For future expansion or specific functionalities.
• HUD interface: For Head-Up Display connectivity.
• Original vehicle instrument fiber optic interface: (Note: 3 Series does not have this interface).

Included Accessories

• Loading tool: (Note: 3 Series does not have this accessory).
• USB cable: For upgrading instruments.

Product Features Overview

• Linux Operating System: Car-level configuration with excellent stability and safety, fast boot time (<2 seconds).
• Support for Original Vehicle Data: Displays original miles/km, tire pressure, oil/water temperature, oil pressure, fuel consumption, auto body balance, and more.
• Multiple Display Modes: Choose from 3 or 4 modes (simple, comfort, technology, track) and 4 theme colors.
• CPU: T5 1.5Ghz.
• Display: HD IPS screen with 1920x720 resolution.
• Easy Installation: Plug and Play, no wire cutting required.
• Multilingual Support: English, Russian, German, French, Spanish, Italian, Korean, Japanese, Arabic, Turkish, etc.

4. Installation Guide

The installation process is designed to be non-destructive, retaining original car information functions without requiring wire cutting or soldering. It is recommended to have professional installation if you are not experienced with automotive electronics.

Installation Steps

1. Step 1: Remove Original Instrument Panel
   Adjust the steering wheel to its lowest position. Use the provided loading tool to hook the second hole above the original instrument panel. Pull down the iron plate from the second to last hole and carefully remove the original instrument panel.

   

2. Step 2: Install New Instrument Panel and Connect Wires
   Remove the iron plate from the original instrument panel and install it onto the new digital instrument panel machine. Insert the corresponding plug wires in pairs, ensuring secure connections.

   

3. Step 3: Secure New Instrument Panel
   Align the bottom of the new instrument machine with the correct position in the dashboard and push it inward until it is securely in place.

   

Compatibility Notes

This product is compatible with various VW models and years. Please verify your specific car model and year before installation. For Tiguan, Jetta, and Scirocco models, there are two types of power cables. Ensure you use the correct cable based on your original dashboard's design (circle inside or circle out).

5. Operation

Steering Wheel Control Keys

The digital dashboard cluster is compatible with your vehicle's multi-function steering wheel. Use the BC (Board Computer) button for navigation and selection.

Functionality:

• Short press [BC]: To select items or navigate menus.
• Long press [BC]: To confirm selections.

Original Vehicle Instrument Search (Fuel Tank Capacity)

To set up the fuel tank capacity:

1. First, fill the car's fuel tank with oil.
2. Start the engine before setting up.
3. Long press the button in the lower left corner of the original instrument panel and select the '10 Unlock' menu to enter.
4. Add the last 5 digits of the chassis number (e.g., if 5+1+9+0+6=21), fill in '21' in the CODE position, then press the key to exit.
5. Select the '13 Tank' menu to enter.
6. Round the 'Tank' and 'Left' values to 36.5L and 37L respectively, and fill these into the main fuel tank settings in the instrument table.
7. Fill 'Tank, right 30L' into the secondary fuel tank settings.

ODO Settings

For initial installation, record the total mileage from your original instrument panel.

1. Navigate to: System Settings -> Factory Settings -> Enter Password [0188] -> Change [Total Kilometers] to match your original vehicle's total kilometers.
2. Select [Save], then long press the steering wheel control button [BC]. Turn off the vehicle, wait for 5 seconds, then restart the car. The setting should be successful.

Vehicle Model Settings

1. Color: System Settings -> Color - Select the color of your own vehicle.
2. Vehicle Type: System Settings -> Factory Settings -> Enter Password [0188] -> [Vehicle Type] Select your specific car model.

Trip Information

View the total mileage, average fuel consumption, and average speed of the car after starting.

Real-Time Information

Check the fuel consumption information and oil temperature of the car.

General Information Display

Monitor tire pressure, tire angle, maintenance status, and other vehicle information.

System Settings

• Date/Time: System Settings -> [Date/time].
• Language: System Settings -> [Language].
• General Setup: System Settings -> [General Setup].
• Day/Night Brightness: System Settings -> [General Setup] -> [Day Brightness]. Adjust brightness levels for day and night driving.
• Driving Mode: System Settings -> [General Setup] -> [Driving mode]. All four UI styles (simple, comfort, technology, track) can be changed to 3 colors: red, yellow, and blue. The AOTU mode automatically switches colors with the driving mode of the vehicle.
• Speed Warning (SpeedWarnOnOff): System Settings -> [General Setup] -> [speedWarnOnOff]. Set on/off. [Speed Alarm] allows you to set a warning when exceeding a certain speed limit.
• Factory Settings: System Settings -> [Factory] -> Enter password [0189]. Here you can set the reverse direction of the front and rear doors, enable or disable startup animation, mileage units, temperature units, fuel nozzle positions, etc.
• Front Door RHD: System Settings -> [Factory] -> Enter password [0189] -> [Front Door RHD]. If the instrument panel displays an error when opening the front and rear doors, you can set it here.
• Doors Info: System Settings -> [Factory] -> Enter password [0189] -> [Doors info]. This needs to be set to enable.
• Fuel Tank Position: System Settings -> [Factory] -> Enter password [0189] -> [Fuel Tank Position]. You can modify it to the right or left according to your own needs.

Theme Selection

Four sets of UI styles can be freely switched to match your preference.

Synchronized Display with Android Player

If you wish to synchronize the Android player's CarPlay function to the digital dashboard, the Android player must be running Android 10.0 or higher. This requires an extra HDMI cable and an exchange box. Please contact customer service for details on purchasing the HDMI cable (additional cost applies) and ensuring compatibility.

Real-time Vehicle Information Display

The cluster provides real-time detection and display of various vehicle parameters, enhancing your driving experience.

Ambient Lighting

The digital dashboard offers 30 colors of ambient lighting, allowing you to change colors for a more immersive experience. The gauges synchronize with the existing ambient lighting colors of your vehicle.

6. Maintenance

The Digital Dashboard Cluster is designed for durability and minimal maintenance. Keep the screen clean using a soft, lint-free cloth. Avoid abrasive cleaners or solvents that could damage the display. Ensure proper ventilation around the unit to prevent overheating.

7. Troubleshooting (FAQ)

General Issues

If you encounter problems, refer to the solutions below. If issues persist, contact customer service.

• How do you change language?
  System Settings → Language
• How to set the time and date?
  System Settings → Date/time
• How to change the mileage/temperature unit?
  System Settings → [Factory] → Enter the password [0189] → Mileage unit/temperature unit
• How to adjust brightness?
  System Settings → [General Setup] → [Day Brightness]

Protocol Upgrade

When the protocol software needs to be upgraded, please inquire with customer service about the software. Copy the software to a USB drive and insert it into the USB port of the cluster to automatically upgrade.

8. Specifications

9. User Tips

• Before installation, ensure the speed limit alarm is set to 250km/h and winter tire settings are turned off in your original dashboard to prevent potential conflicts.
• Always double-check cable connections, especially for models like Tiguan, Jetta, and Scirocco, which may require specific cable types based on the original dashboard's design.
• For optimal performance and to access advanced features like CarPlay synchronization, ensure your Android player is updated to Android 10.0 or higher.

10. Warranty and Support

All products undergo strict quality tests before shipment to ensure high quality. We provide updates for firmware, software, UI, and GPS navigation maps for free.

If the product has a problem within 365 days after receipt confirmation, support for free return and refund within 15 days, or we will replace the new machine directly for you. Please contact customer service first to communicate any issues.

Our engineer team is available to assist with installation and troubleshooting. Please feel free to contact our seller for any questions or support needs.