1. Introduction
The XTOOL InPlus IP819 Diagnostic Tool is a comprehensive automotive scanner designed to interface with a vehicle's Electronic Control Unit (ECU) for various diagnostic and maintenance tasks. It retrieves diagnostic trouble codes (DTCs), accesses data stream information, and performs actuation tests (bi-directional control). This tool supports a wide range of vehicle control systems including engine, transmission, anti-lock brake system (ABS), SRS Airbag system, chassis, and body.
The IP819 features a 1.5GHz Quad-core processor, 2GB RAM, 64GB storage, and a 7-inch touchscreen, ensuring swift operation and seamless multitasking. It includes a built-in speaker, microphone, and rear camera. The device is powered by a 2500mAh 7.3V battery for extended use and supports CAN FD, DOIP, and FCA Protocols.
Key functionalities include full system diagnostics, full OBD II functions, activation tests, ECU coding, vehicle-specific functions, ADAS calibration, VAG guided functions, PMI (Programmable Module Installation), and 39 special functions.
Legal Information
XTOOL is a registered trademark of Shenzhen XTOOL Technology Co., Ltd. This manual contains proprietary information and is protected by copyright. Reproduction or transmission in any form without prior written permission from XTOOL is prohibited.
The information, specifications, and illustrations in this manual are for reference only and may change without notice. XTOOL is not responsible for direct, special, incidental, or indirect damages, including economic losses.
IMPORTANT: Before using or maintaining this unit, read this manual thoroughly and pay close attention to all safety warnings and precautions.
2. Safety Information
This section outlines critical safety instructions to prevent personal injury and damage to the device or vehicle. Always ensure you understand and follow these guidelines.
General Safety Instructions
- Read and Understand: All operators and individuals near the device must read and understand these safety instructions.
- Proper Use: Use the device only as described in this manual. Adhere to safety messages and test procedures from the vehicle or equipment manufacturer.
- Knowledge and Skill: Automotive technicians must be knowledgeable about the system being tested and familiar with proper service methods.
- Acceptable Testing Practices: Perform tests safely to protect yourself, others, and prevent damage to the device and vehicle.
Safety Messages
Safety messages use signal words to indicate hazard levels:
⚠ Danger: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
⚠ Warning: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Specific Safety Warnings
- Ventilation: When the engine is running, ensure the service area is well ventilated or use an exhaust removal system to prevent carbon monoxide buildup.
- Safe Environment: Always perform automotive testing in a safe environment.
- Eye Protection: Wear safety eye protection that meets ANSI standards.
- Avoid Hazards: Keep clothing, hair, hands, tools, and test equipment away from all moving or hot engine parts.
- Transmission and Brakes: Put the transmission in PARK (automatic) or NEUTRAL (manual) and engage the parking brake.
- Wheel Blocks: Place blocks in front of the drive wheels and never leave the vehicle unattended during testing.
- Ignition System Caution: Be cautious around ignition components (coil, distributor cap, wires, spark plugs) as they generate hazardous voltages.
- Fire Extinguisher: Keep a suitable fire extinguisher nearby for gasoline, chemical, and electrical fires.
- Test Equipment Connections: Do not connect or disconnect any test equipment while the ignition is on or the engine is running.
- Clean Equipment: Keep the test equipment dry, clean, and free from oil, water, or grease. Use a mild detergent on a clean cloth.
- No Driving While Testing: Do not drive the vehicle and operate the test equipment simultaneously to avoid distractions.
- Service Manual Reference: Always consult the vehicle's service manual and adhere to diagnostic procedures and precautions.
- Battery Check: Ensure the vehicle battery is fully charged and the DLC connection is secure to prevent damage or false data.
- Avoid Electromagnetic Interference: Do not place the test device on the vehicle's distributor.
3. Setup
3.1 What's in the Box
The XTOOL InPlus IP819 V2.0 package includes the following items:

Image: Contents of the XTOOL IP819 V2.0 box, showing the diagnostic tablet, various cables, and power adapters.
| Name | Quantity |
|---|---|
| IP819 Tablet | 1 |
| VGA to OBD II Main Cable | 1 |
| Type-C to Type-C Charger Cable | 1 |
| Type-C to Type-A Adapter (to PC) | 1 |
| Power Supply Charger US | 1 |
| Power Supply Charger Adapter EU | 1 |
| Power Supply Charger Adapter UK | 1 |
| Color Carton | 1 |
| Tool Case | 1 |
| Packing List | 1 |
| Quick Start Guide | 1 |
3.2 Device Overview and Power Sources
The IP819 Diagnostic Tool can be powered by its internal rechargeable battery pack or an AC power supply.

Image: Front view of the XTOOL InPlus IP819 tablet, showing the main screen and connected OBD cable.
Main Ports of the Tablet:
- Type-C Port
- DB15 Port
- Reset Hole
- Power Button
- Microphone
- Camera
- Speaker
- Nameplate
Internal Battery Pack:
A fully charged internal battery provides approximately 3.5 hours of continuous operation. The battery charges when the tool is connected to the AC Power Supply.
AC Power Supply:
Connect the Diagnostic Tool to a standard AC outlet using the provided AC power supply. Ensure the output cable is plugged into the DC power supply input jack on top of the tool. Use only the provided AC power supply for proper and safe operation.
3.3 Getting Started
Turning On:
Press and hold the power button (top right) for approximately five seconds. The tool will power on automatically if the battery is sufficiently charged or if connected to AC power. If the battery is completely drained, charge it for over 6 hours before attempting to turn it on.
Turning Off:
Press and hold the power button for more than three seconds. The tool will power off.
WARNING: Before turning off, terminate all vehicle communications. Forcing a shutdown during communication may cause issues with the ECM. Never disconnect the OBD-15 main cable while the tool is communicating with the vehicle ECM.
Emergency Shutdown:
Only use this procedure if the Diagnostic Tool is unresponsive or operating erratically. Press and hold the Power button for five seconds until the tool turns off.
WARNING: Using emergency shutdown during communication with the vehicle ECM may lead to ECM problems on some vehicles.
3.4 Wi-Fi Connection
The Diagnostic Tool supports 2.4 GHz or 5.0 GHz Wi-Fi. Swipe up from the bottom toolbar, click Home > Network & Internet, switch on Wi-Fi, and select your network. Enter the password to connect.
If home Wi-Fi is unavailable or problematic, you can connect to a mobile phone hotspot:
- iOS Users: Go to Settings > Cellular Network > Personal Hotspot. Switch on "Allow Others to Join" and "Maximize Compatibility."
- Android Users: Go to Settings > Wireless & Networks > Tethering & Portable Hotspot. Switch on hotspot, configure WLAN hotspot (WPA2 PSK), and ensure "Max connections allowed" is set to allow the Diagnostic Tool.
NOTE: Wi-Fi is not always necessary for diagnostics, but some brands (e.g., Peugeot) require it for online server access during diagnostics.
3.5 Product Activation
- Select a language for the operating system.
- Connect to an available Wi-Fi network.
- For first-time users, the system will guide you to enter a valid email address and set a login password. Click "Register." If already registered, click "Log in" and enter your credentials.
- A "Login Successful" pop-up confirms setup completion.
- Click "Start now" to enter the diagnostic system.
NOTE: If activation fails, contact support at support@xtoolonline.com.
3.6 Vehicle Connection
The scan tool must be connected to the vehicle's OBD-II port to establish communication.
- Turn on the tablet.
- Connect the VGA 15 to OBDII-16 Main Cable to the tablet's DB15 port and the vehicle's OBD port.
- Switch on the ignition and tap the Diagnostic application to start diagnosis.

Image: Connection diagram for the XTOOL IP819 to a vehicle's OBD-II port. The tablet connects via a VGA 15-pin port to an OBDII-16 male connector, which plugs into the vehicle's OBD port.
NOTE: If the OBD port is hard to reach, an extension cable can be purchased.
4. Operating Instructions
4.1 Diagnostic Screen Layout and Icons
Upon turning on, the Diagnostic Tool automatically starts the diagnostic program. The main diagnostic screen features various icons for different functions. A hidden toolbar at the bottom can be revealed by swiping up for 3 seconds.

Image: The main diagnostic screen of the XTOOL IP819, displaying icons for Diagnostic, Special Function, Report, Updates, More, Auto Scan, Remote Control, Settings, and XTOOL.
- Auto Scan: Automatically detects and decodes the VIN, then scans all available electronic control modules for diagnostics.
- Diagnostic: Accesses the diagnostic menu for Auto VIN detection, manual vehicle information input, DEMO program, and OBD-II tests.
- Special Function: Covers commonly performed maintenance services for DIYers and professionals.
- Report: Includes functions for diagnostic reports, data playback, and data viewing.
- Updates: Allows downloading diagnostic software programs individually or in batch.
- More: Provides access to user account setup, workshop profile, subscription period, firmware information, endoscope function, and the user manual (PDF).
- Remote Control: Launches TeamViewer for remote assistance.
- Settings: Customizes language, units, USB mode, OS settings, volume, brightness, and displays device information.
- XTOOL: Provides contact information and social media links for support.
4.2 Main Screen Layout and Icons (Android Tablet)
The main screen of the Android tablet provides access to various applications:
- Calendar: Displays the calendar in day, week, and month views.
- Contacts: Manages contact information; allows adding new contacts or importing from VCF files.
- Clock: Sets alarms, timers, uses the stopwatch, and accesses the clock.
- Email: Creates new email accounts for sending emails or sharing reports.
- Music: Adds new songs, playlists, albums, and artists.
- Sound Recorder: Records voice messages.
- Calculator: Opens the calculator.
- ES File Explorer: Manages documents, reports, files, and folders in memory.
- Adobe Acrobat: Manages PDF files and accesses Dropbox accounts.
- Quick Support: Enables remote control by the tech support team.
- Settings: Configures Android tablet settings (Network & Internet, battery, display, sound, storage).
- Gallery: Views screenshots and screen recordings.
- Video: Views recorded screen recordings.
- Explorer: Views internal memory and edits files.
- Chrome: Accesses the XTOOL website for product support and general browsing.
- Endoscope: Activates the endoscope function for visual inspection in narrow areas.
- Camera: Activates the rear camera to take pictures of vehicle problems.
4.3 Diagnosing Vehicles
To ensure proper communication and diagnostics, the vehicle must be correctly identified.
Vehicle Identification:
Follow screen prompts to enter necessary vehicle information. Options include:
- VIN (Vehicle Identification Number)
- Manufacture area > Model > Year
- Other specific criteria
Auto Scan: The Diagnostic Tool scans and decodes the VIN automatically. If Auto Scan fails, try "Manual Selection" as a reliable alternative.
Automatic Detection: Select region, brand (e.g., "Americas" > "CADILLAC"), then "Automatic Detection" to identify the vehicle.
Manual Selection: The most reliable option if other methods fail. Select region, brand, model year, and model name manually.
Automatic Scan: Scans all available vehicle modules for diagnostics.
4.4 Diagnostic Functions
Once the vehicle is identified, the Diagnostic Tool can access vehicle electronic control systems.
Read Trouble Codes (DTCs):
Displays current emission-related DTCs, including Stored, Pending, and Permanent Codes. DTCs are prioritized by emission severity.
- Stored Codes: Current emission-related DTCs from the ECM.
- Pending Codes: Diagnostic trouble codes whose setting conditions were met but need to be met on two or more consecutive drive cycles before the DTC actually sets.
- Permanent Codes: Records of severe DTCs that illuminated the MIL at some point.
- Generic & Manufacturer-Specific Codes: DTCs are categorized by a letter (P, C, B, U) indicating the system, followed by digits for specific issues.
Clear Trouble Codes:
Erases all emission-related diagnostic data (DTCs, freeze frame data, test results) from the ECM. A confirmation screen will appear before clearing.
WARNING: Clearing codes typically erases associated freeze frame data. If the underlying issue is not resolved, fault codes may reappear.
Live Data (PID Data):
Displays real-time PID data from various sensors. You can view data in a list, individual graphs, analog dashboards, or custom lists of up to 8 sensors. Data can be graphed, recorded, and exported to CSV files for analysis.

Image: The XTOOL IP819 displaying multiple live data streams simultaneously, showing real-time vehicle status and changes.
Read Freeze Frame:
Provides a snapshot of critical parameter values when a DTC is set, helping to analyze the root cause.
I/M Readiness (Smog Check):
Checks the readiness of the monitoring system for emissions compliance. Offers options for "Since DTCs Cleared" and "This Driving Cycle."
O2S Monitoring Test:
Checks the integrity of oxygen sensors, displaying pertinent O2S parameters.
On-Board Monitor Test:
Views results of On-Board Monitor tests for specific systems and components.
Component Test:
Enables bidirectional control of the ECM to test components like EVAP, ABS motor, windows, injectors, lights, etc.
Read Vehicle Information:
Displays vehicle-specific information such as VIN, calibration identification, and calibration verification number.
IMPORTANT: Not all vehicles support all service modes; available selections vary.
4.5 Special Functions (39+ Services)
The IP819 offers over 39 special functions for various maintenance and service tasks. These functions include relearn, reset, match, calibration, adjustment, adaptation, and initialization options.

Image: A collage illustrating various maintenance services such as Oil Reset, Crank Sensor Relearn, Control Unit Reset, TPMS Reset, Throttle Relearn, Injector Coding, Suspension, Gearbox Match, and VGT Relearn.
- Oil Reset: Resets engine oil life system after an oil change.
- EPB Reset: Resets electronic parking brake system after brake pad replacement.
- SAS Adjustment: Calibrates the steering angle sensor.
- BMS Reset: Registers new battery to the ECU and clears low battery fault information.
- Injector Coding: Writes identification codes of fuel injectors into the ECU.
- DPF Regen: Manages Diesel Particle Filter regeneration.
- GPF Regen: Manages Gasoline Particulate Filter regeneration.
- TPMS Reset: Performs learning, matching, and resetting functions for tire pressure sensors.
- ABS Bleeding: Bleeds the brake system to restore ABS brake sensitivity.
- IMMO Reset: Resets or reprograms the Immobilizer System for key matching, key information reset, and key adding.
- ECU Coding: Customizes and reprograms ECU settings for VW, Audi, and Skoda vehicles.
- PMI (Programmable Module Installation): Transfers data from old modules to new ones for ECU replacements (Ford, Lincoln, Mazda).
- ECU Configuration & Re-flash Hidden Function: Activates higher-level car functions and disables annoying features.
- Bi-directional Control / Active Test: Performs active tests on components like EVAP, ABS motor, windows, injectors, lights, etc.
- VAG Guided Function: Provides guided operations for VW, Audi, Skoda vehicles.
NOTE: Special services and hidden functions may not work on all cars. Check compatibility with VIN before purchase.
4.6 Full System Diagnostic Report
After completing diagnostics, you can generate a comprehensive report. Enter VIN, mileage, and model year, then click "OK" to create a diagnostic report for review or sharing. This "Full System Diagnostic Report" differs from the "Fault Code Report" generated during vehicle scan by providing a more detailed health overview of all systems.
Reports can be viewed, shared via email, or printed as PDF files.

Image: The XTOOL IP819 V2.0 Diagnostic Report screen, showing options for report customization, automatic generation, and sharing/printing.
4.7 OBD-II/EOBD Functions
This section covers the concept, protocols, and basic operations of the OBD-II/EOBD function. Access it via Diagnostic > Region Selection > OBD-II.
OBD-II provides generic data for emissions-related diagnostics, including checking DTCs, MIL status, and monitor status for emissions certification.
OBD-II Protocols:
The tool supports J1850PWM, J1850VPW, ISO 9141-2, ISO 14230-4, and ISO 15765-4 (CAN).
CAN FD & DOIP Protocols:
The IP819 supports native CAN FD for post-2020 General Motors vehicles and DOIP for modern BMW (E/F/G chassis), Jaguar, and Land Rover models, without requiring additional adapters.

Image: A world map highlighting regions and car brands supported by CAN FD & DOIP protocols, including America, Europe, and Asia.
FCA AutoAuth:
Supports access to the Security Gateway Module on 2018 and newer FCA vehicles (Chrysler, Dodge, Jeep, Fiat) for diagnostics and active tests without an FCA 12+8 Cable. Note: User must register an FCA account.
5. Maintenance
5.1 Software Updates
The IP819 comes with 3 years of free software updates. After this period, all downloaded features remain fully operational without mandatory subscriptions. You can renew the subscription annually for $99 to receive the latest software versions and features.

Image: A graphic emphasizing "3-Year Free Update" for the XTOOL diagnostic tool, showing a circular update icon.
Updates can be performed via Wi-Fi. If "Network abnormal" messages appear, try a different Wi-Fi network or a mobile hotspot. Contact support if issues persist.
To update: Click "Updates" on the main diagnostic screen. You can update all programs or select individual ones.
Deleting Software Programs:
To free up memory, you can delete rarely used diagnostic software. Go to "Diagnostic" > Select Region > Press and hold the vehicle maker icon for 5 seconds > Click "Delete."
IMPORTANT: Do not delete software programs close to the subscription expiration date. Re-download them before expiration to ensure continued access.
5.2 Storage Management
In the tablet's settings, you can check remaining storage, clear software, and clear cache to optimize performance.
5.3 Cleaning Equipment
Keep the test equipment dry, clean, and free from oil, water, or grease. Use a mild detergent on a clean cloth to clean the outside of the equipment as necessary.
6. Troubleshooting (FAQ)
This section addresses common questions and issues users may encounter.
- Q: I haven't found I/M readiness in the menu.
- A: Go to Diagnostic > Select America/Europe/Asia > Click the "OBD-II" icon > Auto Scan/Select OBD-II Protocol > I/M Readiness.
- Q: Unable to find live sensor data like short-term/long-term fuel trim.
- A: Go to Diagnosis > Select America/Europe/Asia > Click the "OBD-II" icon > Auto Scan/Select OBD-II Protocol > Live Data > LTFT, STFT or similar term.
- Q: I cannot charge the battery. It's nearly dead.
- A: 1. Use the original charging cable or OBD test cable to charge for more than six hours. 2. Hold the shutdown button for 15 seconds to see if it turns on normally (without charging cable). 3. Connect to a computer via USB to see if it's recognized. 4. If issues persist, contact support@xtoolonline.com with a video of the issue.
- Q: Can this scanner still be used once the 3-year free updates are finished?
- A: Yes, you can still use its last updated software version indefinitely. To get new updates, an annual renewal fee of $99 applies.
- Q: I cannot update, Wi-Fi and hotspot both fail.
- A: This might be due to router firewall settings or network provider restrictions. Check your router settings or contact support@xtoolonline.com.
- Q: Why should I connect the scanner to the internet once a month?
- A: This is a government policy requirement to report IP location to prevent illegal activities. If connection issues arise, contact support@xtoolonline.com.
- Q: The auto scan/VIN cannot work on my vehicle.
- A: Auto scan/VIN may not cover all vehicles due to varying ECU VIN storage, database coverage, or specific vehicle communication modes (e.g., Dodge's "sending command, answering command").
- Q: My diagnostic tool cannot connect to Wi-Fi.
- A: If it times out, check your router for WPA2 compatibility and ensure it's not blocking outgoing traffic to non-US regions. A mobile hotspot often resolves registration issues. If connected but showing "connect internet to sync your device," correct the Android system's time zone to match the network time zone (e.g., Pacific time zone).
- Q: What is the update fee of IP819? After my IP819 passes the free subscription date, can I use it as usual as before?
- A: The renewal fee is $99 per year after the 3-year free period. You can continue using the last updated software. To get new updates, you must renew the subscription.
- Q: Shall I connect my device to the Internet/Wi-Fi all the time?
- A: No, only for registration and downloading updates. Some advanced features or specific vehicle brands (like Peugeot) may require an internet connection.
- Q: Does your tools support all functions on all vehicles?
- A: No, while comprehensive, the tool's functions vary by vehicle make, model, and configuration, similar to other scan tools or even factory scanners.
7. Technical Specifications
| Item | Description/Specification |
|---|---|
| Display | 7-inch Touch Screen, 1024×600 Resolution |
| Operating System | Android 10.0 |
| Processor | Quad-Core Processor 1.5GHz |
| Memory | 2G RAM, 64G ROM |
| Connectivity | Bluetooth, Wi-Fi (2.4GHz & 5Ghz), Type-C |
| Operating Method | Flat Panel Touchscreen |
| Upgrade Method | Device Connects to Wi-Fi for Online Upgrade |
| Battery | 7.3V Lithium-Polymer Battery, 2500mAh |
| Tested Battery Life | 3.5 Hours |
| Dimensions | 24.5 × 14 × 3.4 (CM) |
| Wi-Fi | 2.4G/5Ghz |
| Power Consumption | 8W |
| Free Renewal Update | 3 Years |
| Charging Method | Type-C Charging |
| Sensor | Gravity/ Light Sensor |
| Audio | Microphone |
| Supported Protocols | CAN FD/DOIP/FCA |
| Speaker | Built-In Speaker |
| Weight (Including Battery) | 0.72KG |
| Gross Weight | 1.9KG |
| Operating Temp Range (Ambient) | -4°F ~ 140°F (-20°C ~ 60°C) |
| Storage Temp (Ambient) | -40°F ~ 158°F (-40°C ~ 70°C) |
| Operating Humidity | <90% |
| Power Supply Input | 100-240V~50-60Hz 0.5V Max |
| Power Supply Output | 5.0V-3.0A 15.0W/9.0V-2.22A |
8. Warranty & Support
8.1 Limited Two-Year Warranty
Shenzhen XTOOLtech Intelligent Co., LTD. (the Company) warrants this product to the original retail purchaser against defects in material or workmanship for two years from the date of purchase. Defective parts will be repaired or replaced (with new or rebuilt parts) at the Company's option, without charge for parts or labor.
This warranty does not cover:
- Products subjected to abnormal use, accidents, mishandling, neglect, unauthorized alteration, misuse, improper installation/repair, or improper storage.
- Products with removed, altered, or defaced mechanical or electronic serial numbers.
- Damage from excessive temperature or extreme environmental conditions.
- Damage from connection to, or use of, any accessory or product not approved by the Company.
- Defects in appearance, cosmetic, decorative, or structural items.
- Products damaged from external causes such as fire, dirt, sand, battery leakage, blown fuse, theft, or improper usage of any electrical source.
8.2 Contact Us
For technical assistance, warranty claims, or any other inquiries, please use the following contact information:
- Website: https://www.xtoolonline.com
- E-mail: support@xtoolonline.com
- Address: Room 601, Block A, Zaoan Business Building, Shigu Road, Xili Residential District, Nanshan District, Shenzhen
- Corporate & Business Inquiries: business@xtoolonline.com, sales@xtoolonline.com
- Social Media: Search for "xtoolonline" on TikTok, Instagram, Facebook, and YouTube.
You can also refer to the User Manual (PDF) for additional guidance.
8.3 Remote Control & Data Logging
If you require remote assistance from the technical team, ensure the Diagnostic Tool is connected to Wi-Fi. Launch TeamViewer via the "Remote Control" icon and provide your TeamViewer ID. Schedule sessions in advance.
For software-related issues, data logging provides crucial information. Keep your tool connected to Wi-Fi for at least 15 minutes and provide your Serial Number (S/N) to support for log access and analysis.
For app-related issues, request an app logging collection tool from technical support.
9. User Tips
- Language Change: To change the menu language, contact XTOOL support with your device serial number to authorize the desired language software program.
- VIN Entry: When manually entering a VIN, note that letters Q, I, and O are typically grayed out on the keyboard as they are not used in standard VINs to avoid confusion with numbers 1 and 0.
- File Transfer: To transfer data to a PC, connect the device via Type-C cable, swipe down from the top of the screen, and enable "Data Transfer." For Android phones, use Bluetooth transfer. iOS devices are not supported for direct file transfer.
- Printer Setup: For printing services, install a compatible Print Service App/Driver (e.g., Mopria) on the Diagnostic Tool. Ensure your printer supports Wi-Fi Direct.
- Trial Mode Limitations: While trial mode allows familiarization, some functions may be limited without account registration. Registering an account is recommended for full functionality.