Introduction
This manual provides comprehensive instructions for the operation and maintenance of your BAOFENG MINI5 Handheld Radio. The MINI5 is an ultra-slim, portable two-way communication device featuring VHF/UHF and Air Band reception, 999 channels, Type-C charging, and wireless programming capabilities. Please read this manual thoroughly before using the device to ensure safe and optimal performance.
Package Contents
Verify that all items listed below are included in your package. If any items are missing or damaged, please contact your retailer.
| Item | Quantity (PCS) | Item | Quantity (PCS) |
|---|---|---|---|
| Radio | 1 | Power Adapter | 1 |
| Battery | 1 | Lanyard | 1 |
| Antenna | 1 | Operation Manual | 1 |
| Belt Clip | 1 |
The charger and power supply are connected to the device. Note that charging methods described in this manual may not be appropriate if using a Type-C charging method.

Product Overview
Familiarize yourself with the components of your MINI5 radio.


Parts Description
- Antenna
- SK1-Customized Function Keys/Monitor button
- PTT-A Button
- A/B button
- Menu button
- PTT-B Button
- Numeric Keypad/ Speaker
- Flashlight
- Volume/Power Knob
- Screen
- Accessory Port
- Exit button
- ▲Up button/▼ Down button
- Flashlight/Search button
- Microphone
- LED Indicator
- Battery Latch
- Type-C Charging indicator light
- Type-C Charging Port
- V/M-VFO/MR button
- Belt Clip
LCD Display Icons
| Icon | Description |
|---|---|
| RSSI | Squelch Open/Close Indicator |
| H/L | Transmit power level indicator, According to Power |
| ♪ | Make sure you can hear the DTMF side tone from the radio speaker, set to DT-ST, ANI-ST, DT+ANI. |
| D | DCS enabled |
| C | CTCSS enabled |
| + | Enables access of repeaters in VFO/Frequency Mode. TX will be shifted higher in frequency than RX. |
| - | Enables access of repeaters in VFO/Frequency Mode. TX will be shifted lower in frequency than RX. |
| D | Dual watch enabled |
| 0 | Keypad lock enabled |
| VOX icon | VOX enabled |
| Confidential call icon | The confidential calling feature is activated |
| N | Narrowband enabled |
| Battery level icon | Battery level indicator |
| R | Reverse function enabled |
| T | The terminal is switched from transit mode to pass-through mode. |
| SCR | The voice scramble function has been activated |
Setup
Attaching the Antenna
Turn the antenna clockwise until it is tight. To remove the antenna, turn it counterclockwise.
CAUTION:
- Do not hold the radio antenna in your hand, as this will reduce the performance of the radio and the life of the antenna.
- Do not shake the radio with the top of the antenna in your hand, as this will degrade the performance and life of the radio antenna.
Charging the Battery
When using the terminal for the first time, a low battery warning may occur. It is recommended to turn off the radio during charging. The battery's LEDs provide an indication of the current state of charge:
| Indicator light | Charging status |
|---|---|
| Red light is always on | Charging |
| Green light is always on | Charging complete |
The MINI5 features a Type-C universal fast charging interface, compatible with power banks, car chargers, and mobile phone chargers.

Wireless Programming (OLA Radio APP)
The BAOFENG MINI5 supports wireless programming via the OLA Radio APP, allowing you to adjust frequencies and set parameters directly from your mobile phone without needing a computer or programming cables.
- **Download the APP:** Scan the QR codes below to download the OLA Radio App for Android or iOS.

Figure 5: OLA Radio App QR Codes for Android and iOS. - **Connect the Radio:**
- Open the OLA Radio App.
- Enable Bluetooth and location services on your mobile phone.
- Select the "5Rmini Series" walkie-talkie model within the app.
- Click on "Walkie-talkie" to connect. A "connection success" message will appear, and you can return to the home page.
- **Program the Radio:**
- **Read Radio Data:** After reading the frequency, click "program" to enter program details. In this interface, you can program channel information, frequency mode, and optional functions.
- **Save Profile:** The programmed profile can be saved as a new profile with a custom name. If you select "Replace Program," click "Replace Program" and save.
- **Write Data to Radio:** From the home page, select "program," then click "Write" to transfer the frequency settings to the radio. The radio will automatically restart once the writing process is complete.

Operating Instructions
Basic Operations
- **Turning the Radio On/Off:**
- To turn ON: Turn the [Volume/Power] rotary knob clockwise.
- To turn OFF: Turn the [Volume/Power] rotary knob counterclockwise.
- **Setting the Volume:**
- To increase volume: Turn the [Volume/Power] rotary knob clockwise.
- To decrease volume: Turn the [Volume/Power] rotary knob counterclockwise.
- CAUTION: Do not hold the radio close to your ear if the volume is set to an uncomfortable level, as it could cause hearing damage.
- **Locking or Unlocking Keypad:**
- To lock: Press and hold the [*] key until the screen displays the lock icon.
- In lock mode, you can still turn the radio on/off, adjust volume, receive/transmit, send call tones, send emergency alerts, and listen to channels. All other functions remain locked.
- To unlock: Press and hold the [*] key again until the lock icon disappears.
Keypad Entry
You can enter radio aliases, channel aliases, numbers, etc., using the numeric keypad.
- To switch between input methods, press the [#] key.
- Press [1] to enter a special character (except in numeric input mode).
- Press [0] to enter a space (except in numeric input mode).
Channel Selection and Management
- **Selecting a Channel:**
- Press the [V/M] button to toggle between VFO (Frequency Mode) and Channel Mode.
- Use the ▲/▼ buttons or the rotary encoder to select the desired channel.
- To enter a channel number directly, use the keypad (e.g., for channel 64, enter "064").
- **Channel Memory:**
- In Frequency and Standby mode, you can store frequencies and parameters.
- Press [MENU] [3] [MENU] [5]. The screen will display "MEMCH".
- Press [MENU] to enter the function. Use the ▲/▼ buttons or the rotary encoder to select the channel, then press [MENU] to store it. A sound tone will confirm success.
- Press [EXIT] to return to standby mode.
- NOTE: Set CTCSS tones, DCS codes, or frequency offset before storing the channel. Stored channels are displayed as "CH-".
- **Deleting a Channel (DEL-CH):**
- In VFO mode and Standby mode, press [MENU] [3] [MENU] [1] [6]. The screen will display "DELCH".
- Press [MENU] to enter the function. Use the ▲/▼ buttons or the rotary encoder to select the channel to delete, then press [MENU] to confirm.
- Press [EXIT] to return to standby mode.
- NOTE: Channel 1 cannot be deleted.
Frequency Settings
- **Main Band/Sub-band Switch:**
- In standby mode, press the [A/B] key to switch between the A and B bands. The main band is highlighted.
- **Setting the VFO Frequency:**
- Turn the radio to VFO mode, then press the [A/B] key to switch to the main channel.
- **Operation 1:** Input the VFO frequency directly with the keypad.
- **Operation 2:** Use the ▲/▼ button or rotary encoder to adjust the VFO frequency in the set frequency step.
- **Reverse Frequency Function:**
- In relay mode, short press the [*] key to invert the receive and transmit frequencies. The screen shows the "R" icon.
- This function is often used in repeater channels with frequency differences between receive and transmit.
- **Talk Around Function:**
- In repeater mode, press [*] to switch between Talkaround Mode and Repeater Mode. The screen displays "T" (Talkaround) or "R" (Repeater) icon.
- In Talkaround mode, the receive frequency equals the transmit frequency.
- **Repeater Activation Tone:**
- Turn on the radio, press and hold the [PTT] key, then press the [SK1] key to transmit a 1750Hz audio tone to activate a repeater in hibernation.
Communication Functions
- **Call Service:**
- All radios in the group must be set to the same channel and sub-code to communicate.
- For optimal reception, keep the microphone 2.5 cm to 5 cm from your mouth when transmitting.
- **Initiate a call (PTT-A):** Select a channel, press and hold [PTT-A]. The radio transmits on segment A (upper screen), and the red indicator light is on. Speak into the microphone.
- **Initiate a call (PTT-B):** Press and hold [PTT-B]. The radio transmits on segment B (lower screen), and the red indicator light is on. Speak into the microphone.
- **Receive a call:** After releasing the [PTT] key, the radio is in a receivable state. The green indicator light is on when receiving a call.
- **Voice-activated Transmission (VOX):**
- Enables transmission without pressing PTT, by voice. Transmission stops automatically when speech ends.
- To enable: In standby, press [MENU] [2] [MENU] [4] to enter Vox Switch.
- To set VOX level: Press [MENU] [2] [MENU] [5]. Use ▲/▼ to select level (1-9). Lower values mean higher sensitivity. The "V" icon appears on the screen. Default is off.
- To disable: Select "OFF OFF" in the Vox Switch menu.
- **Dual Watch:**
- Allows the radio to receive frequencies set for both channel A and B.
- Press [MENU] [2] to enter Radio Set.
- Press [MENU] + ▲/▼ to select "15 Dual Watch".
- Press [MENU] to enter Dual Watch Setting, then ▲/▼ to select "On".
- Press [MENU] to save. The "D" icon will appear on the screen.
- To disable: Select "Off" in the Dual Watch Setting menu.
Additional Functions
- **Emergency Alarm:**
- Initiates an emergency alarm.
- In standby mode, press the preset [SoS] shortcut key to enable or disable.
- **Flashlight:**
- In standby mode, press the preset [LAMP] shortcut key or the dedicated flashlight button to turn on/off.
- **FM Radio Function:**
- Set the [SK1] key to "FM Radio" via Menu >> Radio Set >> Press SK1.
- Turn on the radio and press the SK1 key [FM Radio] to enter radio mode. The screen displays the tuning frequency.
- Use ▲/▼ to search for channels at the preset step frequency.
- Press [#↑] to automatically search for channels ("SeeK.." displayed).
- Press [EXIT] to switch frequency band (65.0/75.0MHz).
- Press SK1 key [FM Radio] to exit radio mode.
- **Monitor:**
- Press and hold the pre-programmed [Monitor] key to enter monitor mode and listen for weak signals.
- Release the [Monitor] key to exit.
- **Frequency Search:**
- Press the pre-programmed [SEARCH] shortcut key or hold down the search button. The radio enters frequency search state ("SEARCH...." displayed).
- Press [#Z] to switch the searching band (VHF/UHF, etc.).
- Frequency and CTCSS/DCS code will be displayed after search completion.
- Press [MENU] to save the channel.
- **Stopwatch Function:**
- Press and hold the [MENU] key to enable.
- Press [MENU] to start, press [MENU] again to stop.
- Press [EXIT] to exit.
Using Menu Functions
- **Using Arrow Keys:**
- Press [MENU] to enter the menu.
- Use ▲/▼ buttons or the encoder to navigate.
- Press [MENU] to select an item.
- Use ▲/▼ buttons or the encoder to select a parameter.
- To confirm: Press [MENU] to save and return to the main menu.
- To cancel: Press [EXIT] to reset and exit the menu.
- To exit menu at any time: Press [EXIT].
- **Using Shortcuts:**
- Press [MENU] to enter the menu.
- Use the numerical keypad to enter the menu item number.
- Press [MENU] to enter the item.
- To enter the parameter: Use arrow buttons or numerical shortcut code.
- To confirm: Press [MENU] to save and return to the main menu.
- To cancel: Press [EXIT] to reset and exit the menu.
- To exit menu at any time: Press [EXIT].
Maintenance
- **General Care:** Keep the radio clean and dry. Avoid exposure to extreme temperatures, humidity, or direct sunlight.
- **Battery Care:** To prolong battery life, avoid overcharging and fully discharging the battery frequently. Store the radio with a partially charged battery if not used for extended periods.
- **Antenna:** Ensure the antenna is securely attached. Do not use the radio without an antenna, as this can damage the device.
- **Cleaning:** Use a soft, damp cloth to clean the radio's exterior. Do not use harsh chemicals or solvents.
Troubleshooting
- **No Power:**
- Check if the battery is properly installed and charged.
- Ensure the Volume/Power knob is turned clockwise to the ON position.
- **Cannot Transmit or Receive:**
- Verify that the radio is on the correct channel and sub-code for communication.
- Check antenna connection.
- Ensure the PTT button is functioning correctly. (One user reported a defective PTT button).
- Confirm that the frequency is correctly programmed. Refer to the "Wireless Programming" section.
- **Poor Sound Quality:**
- Adjust the volume level.
- Ensure the microphone is 2.5-5 cm from your mouth during transmission.
- Check for obstructions around the speaker and microphone.
- **Keypad Locked:**
- If the keypad is locked, press and hold the [*] key to unlock it.
- **Difficulty with Frequency Binding/Programming:**
- Refer to the "Wireless Programming (OLA Radio APP)" section for detailed instructions on using the app.
- Ensure Bluetooth and location services are enabled on your smartphone during programming.
User Tips
- **Easy Programming:** The radio is very easy to program directly from the keyboard for common channels like PMR.
- **Good Sound Quality:** Users report good sound quality for communication.
- **Long Standby:** The larger battery capacity provides long standby times.
- **Antenna Upgrade:** Consider a more expensive antenna for potentially improved reception distance.
- **Clear Display:** The display is crisp and pleasing to the eye.
Technical Specifications
| Feature | Specification |
|---|---|
| Receiver Frequency | FM 76-108 MHz; VHF 144-146MHz, UHF 430-440MHz |
| Transmission Frequency | VHF 144-146MHz, UHF 430-440MHz |
| Channel Spacing | 25.0KHz (Wide)/12.5KHz (Narrow) |
| Memory Channel | 999 Groups |
| Operation Voltage | DC 7.4 V ±10% |
| Dimensions | 108mm × 52mm × 39mm (Without Antenna) |
| Weight | 212g (Battery pack included) |
| Transmission Current | ≤1600mA |
| Receive Sensitivity | 0.25μV (12dB SINAD) |
| Rated Audio Power Output | 1W @16 ohms |
| Receive Current | ≤380mA |
| Connection for Accessories | 2 pin Kenwood jack |
| Antenna Impedance | 50 Ohms |
NOTE: All specifications may be modified without prior notice or liability.
Warranty and Support
For detailed information regarding the EU Declaration of Conformity, warranty terms, and customer support, please refer to the official user manual PDF. You can find the PDF document at: User manual (PDF).
The EU Declaration of Conformity, as per Directive 2014/53/EU, is available via the manufacturer's website or by contacting their support. For full details, including contact information for local Baofeng helpdesks or email support, please consult the PDF manual or the manufacturer's official resources.