KEVANLY T10 W5W 194 168 LED Car Interior Light Bulbs

1. Product Information

This product consists of T10 W5W 194 168 LED bulbs designed for various automotive interior and exterior lighting applications. These high-brightness, energy-saving LEDs are intended to replace standard halogen bulbs, offering enhanced illumination and clarity.

• Product Name: T10 LED Car Interior Light
• Model: T10 W5W 194 168
• Brand: KEVANLY

2. Safety & Warnings

Important Safety Information:

Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

• Keep the device and its cord out of reach of children under 3 years old.
• Keep away from children unless supervised by an adult.
• Do not use this product for purposes other than its intended use.
• Inspect the product before each use; do not use if damaged.
• Follow installation and operation guidelines to avoid injury.
• Do not expose to water or moisture (for electrical products).
• Handle with care to avoid cuts or injuries (if sharp/dangerous).
• For DC12V automotive electrical systems only. Never connect to 24V power sources to prevent LED burnout.
• Handle with bare hands during installation/replacement. Do not touch LED chips with sharp objects to prevent damage.
• Avoid touching the lamp body immediately after prolonged use to prevent burns from high temperatures.
• Do not disassemble the lamp body; doing so will void the warranty.

3. Specifications

Figure 1: T10 LED Bulb Specifications

Figure 2: T10 LED Bulb Dimensions

Figure 3: T10 LED Bulb Component Diagram

4. Setup (Installation)

These LED bulbs are designed for plug-and-play installation without modification.

1. Preparation: Before installation, turn off the vehicle power and remove the key to prevent electrical short circuits.
2. Locate Bulb Position: Locate the original T10 bulb position (e.g., daytime running lights, license plate lights, dome lights, etc.).
3. Remove Old Bulb: Pinch the socket and twist/pull out the original bulb.
4. Install New LED Bulb: Align the positive and negative terminals of the LED bulb with the socket and insert fully. Gently shake to confirm secure seating.
5. Test Functionality: Turn on the power to test if the light illuminates normally.

5. Operating Instructions

Once properly installed, the T10 LED bulbs will operate automatically with your vehicle's electrical system. They are designed for continuous operation in their designated lighting applications.

Figure 4: T10 LED Bulbs in various colors

Figure 5: T10 LED Bulbs illuminating car headlights in different colors

6. Maintenance

These LED bulbs require minimal maintenance. To ensure optimal performance and longevity:

• Cleaning: Periodically clean the surface of the bulbs and surrounding light housing with a soft, dry cloth to remove dust and debris. Avoid abrasive cleaners.
• Connection Check: If you experience intermittent lighting, check the bulb's connection in the socket to ensure it is secure.
• Avoid Physical Damage: Protect the bulbs from physical impact or sharp objects, which can damage the LED chips or housing.

7. Troubleshooting

• Lights Fail to Illuminate:
  1. Remove the bulb.
  2. Reverse the polarity (swap positive/negative connections).
  3. Reinsert the bulb and secure by replacing the socket cover.
  4. Test again.
• Light Flickers or Fails Intermittently:
  1. First, check for secure socket contact.
  2. Verify the vehicle's electrical system is functioning properly.
  3. Use only after troubleshooting is complete.

8. User Tips

• Always ensure the vehicle's power is off before attempting installation or removal of bulbs.
• Double-check the polarity if the bulb does not light up on the first attempt. LEDs are polarity-sensitive.
• These bulbs are designed for easy installation, but if you encounter difficulty, consult a professional automotive technician.
• The energy-saving design and built-in load resistors help prevent error messages in most vehicles, but some sensitive systems may still require additional decoders (not included).

9. Compliance Information & Support

This product complies with EU RoHS and REACH environmental directives. It meets LVD 2014/35/EU low-voltage electrical regulations and EMC 2014/30/EU electromagnetic compatibility regulations. The light brightness conforms to EU vehicle lighting standards, making it suitable for use in the EU market.

Warning:

• Installation must comply with local vehicle modification regulations.
• This product cannot replace core vehicle warning/lighting functions.
• The manufacturer assumes no liability for light damage or vehicle issues resulting from circuit failure or improper installation.

Manufacturer & EU Representative Information:

• Manufacturer: Guangzhou Kejie Trading Co. Room 302, No.10, Ou Gang North Street, Ke Mu Long West Road, Tianhe District, Guangzhou City, Guangdong Province, China.
• EU Authorized Representative: SUCCESS COURIER SL, Calle de RIO TORMES 13A, office 1, Fuenlabrada, Madrid, 28947 Spain.
• Importer: Guangzhou Kejie Trading Co. Room 302, No.10, Ou Gang North Street, Ke Mu Long West Road, Tianhe District, Guangzhou City, Guangdong Province, China.

For further details or a downloadable version of the user manual, please refer to the official PDF document: User Manual (PDF)