HEGEHE Solar Powered COB Neon Rope Light User Manual

1. Setup Instructions

Follow these steps to properly set up your Solar Powered COB Neon Rope Light:

1. Initial Charge: Before first use, turn the switch on the solar panel to the 'ON' position. Place the solar panel under direct sunlight for 8-10 hours to fully charge the internal battery.
2. Solar Panel Placement: Install the solar panel in an open area that receives full, direct sunlight throughout the day, free from any shadows cast by trees, buildings, or other obstructions.
3. Light Strip Installation: Fix the neon strip using appropriate hooks or ties onto walls, fences, railings, or around plants. The strip is flexible and can be bent into various shapes for decorative purposes.
4. Outdoor Protection: If installing outdoors, ensure all connections and the ends of the LED strip are protected within a watertight enclosure or completely sealed to maintain IP67 waterproof rating.
5. Cutting the Strip: The light strip has a cutting surface of 10x5mm and can be cut every 3.8 cm. This allows for customization to fit multiple scenarios.
6. Adhesion: The strip features strong double-sided adhesive tape on the back for one-step installation. For outdoor or uneven surfaces, consider additional mounting solutions for secure placement.

Solar Panel Configurations

The solar panel size and battery capacity vary depending on the length of the LED strip purchased:

• 0.5m - 2m Strip: Includes a 1.3W solar panel with 1200mAh battery.
• 3m - 5m Strip: Includes a 2.8W solar panel with 2400mAh battery.
• 6m - 10m Strip: Includes a 6W solar panel with 7200mAh battery.
• 2-Roll Set: Includes a 13W double-output solar panel.

2. Operating Instructions

Your Solar Powered COB Neon Rope Light is designed for automatic operation:

1. Automatic Light Control: The light features a built-in light sensor. During daylight, the light will automatically turn OFF, and the solar panel will charge the internal battery. At dusk or night, the light will automatically turn ON using the stored energy.
2. Manual Mode Selection: Press the 'MODE' button on the control box of the solar panel to cycle through the 8 available lighting effects (Combination, In Waves, Sequential, Slow Glow, Chasing/Flash, Slow Fade, Twinkle/Flash, Steady On).
3. Testing During Daylight: To test the light during daylight hours, you must completely cover the solar panel (e.g., with a thick cloth or cardboard) to simulate darkness. The light will switch on within a few seconds.
4. USB Charging: If charging the product via a USB cable (connected to a power adapter), the solar panel's light sensor is bypassed. The light can operate during the day while charging via USB without needing to cover the solar panel.

3. Maintenance

To ensure optimal performance and longevity of your light strip:

• Solar Panel Cleanliness: Keep the surface of the solar panel clean and free of dust, dirt, snow, or any obstructions that might block sunlight.
• Sunlight Exposure: Ensure the solar panel is consistently exposed to sufficient direct sunlight for normal charging.
• Water Immersion: Although the light strip is waterproof (IP67), do not immerse it in water for extended periods.
• Long-Term Storage: If the product will not be used for a long time, fully charge the battery and store the unit in a cool, dry place.

4. Troubleshooting

If you encounter any issues with your Solar Powered COB Neon Rope Light, refer to the following:

• Light Does Not Turn On:
  • Check if the switch on the solar panel is in the 'ON' position.
  • Ensure the solar panel has received adequate sunlight for charging. Recharge under direct sunlight.
  • If the battery is old or degraded, it may need replacement.
• Dim Lighting:
  • Clean the surface of the solar panel to remove any dirt or debris.
  • Ensure the solar panel receives full-day direct sunlight exposure without any shading.
• Mode Button Not Working:
  • Try restarting the switch (turn OFF then ON).
  • Reset the mode button by pressing it multiple times or holding it down briefly.

5. Specifications

6. User Tips

• Optimal Brightness: Ensure the solar panel receives ample direct sunlight for 8-10 hours daily to achieve optimal brightness and runtime during the night.
• Secure Adhesion: While the strip comes with double-sided tape, for outdoor installations or on rough surfaces, consider using additional adhesive or mounting clips to ensure the strip remains securely in place.
• Uncoil Before Use: Always uncoil the entire LED strip before powering it on to prevent overheating and potential damage.

7. Warranty & Support

For any questions, concerns, or support regarding your HEGEHE Solar Powered COB Neon Rope Light, please follow these guidelines:

1. Contact Customer Service: If you have any questions about the product, please contact our store customer service via AliExpress Message.
2. Provide Order Details: When consulting, please provide your order number and relevant photos/videos of the product problem for quick verification.
3. Response Time: We aim to reply to your inquiries within 24 hours (during working days) and provide a satisfactory solution, which may include a refund, replacement, or partial compensation.

For further details, you may refer to the official user manual PDF: View User Manual (PDF)

Important Note: Do not modify the product for any purpose without the guidance of a professional electrician. We are not responsible for damage caused by modified products.