YTYIN Car LED Laser Fog Light

Contents

YTYIN Car LED Laser Fog Light

Anti-Collision Rear Tail Warning Lamp

Model: Car LED Laser Fog Light

Product Overview

The YTYIN Car LED Laser Fog Light is designed to enhance vehicle visibility and provide an anti-collision warning for the rear of your vehicle, especially during night driving or in adverse weather conditions such as fog, rain, or snow. It projects a bright red laser warning light onto the ground, making your vehicle more noticeable to following traffic and helping to prevent accidents.

Safety & Warnings

Important Safety Information: Read all instructions before use. Failure to follow these instructions may result in damage to the device or personal injury.

  • Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture beyond its IPX4 rating.
  • Handle with care to avoid cuts or injuries.
  • Laser Safety Grade: Class 3B. Avoid direct eye exposure to the laser beam.

Package Contents

Verify that all items are present in the package:

  • 1 x LED Laser Light module
  • 1 x Mounting Bracket
  • 1 x 3M Adhesive Glue pad
  • Fixing screws (some)
Components of the laser fog light kit
Figure 1: Components of the laser fog light kit, including the laser module, bracket, screws, and adhesive.
Contents of the product package
Figure 2: Contents of the product package, showing the laser light, bracket, 3M adhesive, and fixing screws.

Setup & Installation

  1. **Before First Use**: Remove all protective films from the device.
  2. **Mounting Placement**: The laser light is suitable for all vehicles. Install it above the center of the rear license plate.
  3. **Attach the Bracket**: Tear off the backing from the double-sided adhesive pad and attach it to the laser light module. Secure the laser light module to the vehicle, typically above the rear license plate, using the adhesive and/or the provided fixing screws.
  4. **Wiring**: Connect the power cable of the laser light to your vehicle's electrical system. It is recommended to connect it to a power source that activates with your vehicle's tail lights or brake lights for optimal warning functionality.
  5. **Adjust Angle**: Once installed and powered on, adjust the laser light irradiation angle to the ground. The maximum adjustable angle is ±90 degrees from top to bottom. Tighten the screws to secure the angle.
  6. **Charging (if applicable)**: If your device requires charging (not typical for this product, but mentioned in generic instructions), connect the provided USB cable to a certified 5V power adapter.

Operating Instructions

  1. **Power On**: The laser light will activate when connected to the appropriate power source (e.g., when your vehicle's tail lights or brake lights are on).
  2. **Operation**: The device projects a red warning light on the ground behind your vehicle. This creates a visual barrier, alerting drivers behind you to maintain a safe distance, especially in low visibility conditions.
  3. **Mode Change**: If your model has multiple modes (e.g., flashing, steady), short press the power button (if present and accessible) to change modes.

The laser light provides a clearer position of your vehicle and can indicate turning direction if wired appropriately, enhancing overall road safety.

Car with laser fog light in foggy conditions
Figure 3: Laser fog light projecting a red triangle and line on the road in foggy conditions.
Car with laser fog light on a wet road during rain
Figure 4: Laser fog light in action on a wet road during rainy weather.

Maintenance & Storage

  • **Cleaning**: Turn off the device before cleaning. Use a soft, lint-free cloth to wipe the lens and housing.
  • **Storage**: Store in a dry place at room temperature (15°C - 35°C).
  • **Long-term Storage**: If not used for a long time, ensure the device is clean and stored in a suitable environment.

Troubleshooting

If the product does not function as expected, stop using it and check the following:

  • **Installation/Setup**: Verify correct installation and wiring. Ensure all connections are secure.
  • **Power Supply**: Check the vehicle's power supply and ensure the voltage is within the recommended range (8V-36V, 12-24V recommended).
  • **Damage**: Inspect the device for any visible damage. Do not use if damaged.

Stop using it immediately if you notice abnormal heat, smell, smoke, leakage, deformation, or unusual noise.

Specifications

Feature Specification
Brand Name YTYIN
Item Type Warning Lights Assembly
Laser Power 200mw
Lamp Type LED
Laser Wavelength 650mm (red color)
Voltage 8V-36V (12-24V Recommended)
Working Temperature -20°C ~ 70°C
Laser Safety Grade Class 3B
Maximum Adjustable Angle ±90 degrees (top to bottom)
Waterproof Grade IPX4
Material Aluminum + ABS plastic
Laser Light Head Size Approx. 18mm * 27mm
Bracket Size Approx. 22mm * 40mm
Package Length 13 cm
Package Width 13 cm
Package Height 6 cm
Package Weight 0.06 kg

Disposal & Recycling

  • Do not dispose of the product with general household waste. Special disposal rules apply for electronic products.
  • Follow local environmental and waste disposal regulations for proper recycling.

Warranty & Support

For support or inquiries, please contact the manufacturer or seller. A detailed user manual is also available in PDF format: User manual (PDF).

Manufacturer: Fuzhou Hanpin E-Commerce Co., Ltd.

Contact Email: 271135095@qq.com

EU Authorized Representative: NOUR TRADING GMBH

Contact Email: successservice3@gmail.com

User Tips

No specific user tips are available from reviews or Q&A at this time. Please refer to the installation and operating instructions for best performance.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.