1. Important Safety Information & Warnings
Please read all instructions carefully before use. Failure to follow these instructions may result in damage to the product or personal injury.
- Warning: Keep the device and its cord out of reach of children under 3 years old.
- Keep away from children unless supervised by an adult.
- Do not use this product for purposes other than its intended use.
- Inspect the product before each use; do not use if damaged.
- Follow installation and operation guidelines to avoid injury.
- Do not expose to water or moisture.
2. Setup & Installation
2.1. Preparation Work (Safety First)
- Power Off When Parking: Park the car steadily and engage the handbrake.
- Disconnect Battery: Be sure to disconnect the negative cable of the car battery before proceeding.
2.2. Removing the Old Light
- Open the tailgate (if applicable for rear lights, for front bumper lights, access from under the bumper or wheel well may be needed).
- Locate and remove the tail light repair cover from the inside.
- Disconnect the existing electrical plug.
- Unscrew any fixing nuts or bolts.
- Carefully pull out the old lamp assembly from its mounting position.
2.3. Installing the New Light (Test First, Then Fix)
Pre-Testing:
- First, connect the new light plug to the original car harness.
- Reconnect the car battery.
- Turn on the power and test whether the brake lights, turn signals, reverse lights, and driving lights (DRL/fog lamps) are all lit up normally.
Formal Installation:
- After confirming that all functions are normal, disconnect the car battery again.
- Align the new light assembly with its designated position and carefully install it.
- Tighten all fixing nuts or bolts from the inside to secure the light.
- Finally, firmly connect the electrical plug and replace any maintenance covers removed earlier.
2.4. Wiring Diagram
Refer to the diagram below for correct wiring connections:

Wiring Connections:
- Black wire: Connect to NEGATIVE (Ground)
- Red wire: Connect to ACC (Accessory Power)
- Yellow wire: Connect to Turn Signal circuit
2.5. Installation Effect
Observe the visual improvement after installation:

This image shows the vehicle's front bumper before and after the LED DRL fog lamps are installed, highlighting the enhanced aesthetic and lighting.
2.6. Product Demonstration Video
Watch this video for a visual guide on the product's features and lighting effects:
This video demonstrates the startup animation, daytime running light (white), and turn signal light (yellow) functions of the LED DRL fog lamps, as well as the fog lamp's yellow and white light modes.
3. Operating Instructions
This product features a 3-in-1 integrated design, providing multiple lighting functions:
- White Daytime Running Light (DRL): Provides enhanced visibility during daylight hours.
- White/Halogen Fog Lamp: Improves visibility in foggy or low-visibility conditions.
- Amber Sequential Turn Signal: Provides clear and dynamic indication for turns.
3.1. Lighting Effects
Observe the different lighting modes:

This image illustrates the bright white output of the Daytime Running Light and the amber sequential illumination of the Turn Signal Light.
4. Maintenance
4.1. Final Inspection After Installation
- Function Review: Reconnect the car battery and perform a final check of all lighting functions (DRL, fog lamp, turn signals) to ensure they operate correctly.
- Sealing Inspection: After washing the car or pouring water over the light area, check for any severe water ingress or fogging inside the lamp. Slight fogging is normal and should clear up and dry naturally when the lights are on.
4.2. Weather Resistance
The product is designed with IP67 full waterproof, dustproof, and shockproof ratings, making it suitable for various weather conditions.

This image demonstrates the product's ability to adapt to rainy, foggy, snowy, and dusty weather conditions.
5. Troubleshooting
If you experience issues with your LED DRL Fog Lamps, consider the following:
- Lights Not Turning On:
- Check all wiring connections (Negative, ACC, Turn Signal) for secure contact.
- Ensure the car battery is properly connected and has sufficient charge.
- Verify that the vehicle's light switches are in the correct position.
- Inspect fuses related to vehicle lighting.
- Flickering Lights:
- Check for loose wiring connections.
- Ensure proper grounding.
- One Light Not Working:
- Swap the non-working light with the working one (if possible) to determine if the issue is with the light unit or the vehicle's wiring.
- Inspect the specific wiring for that light.
- Water Inside the Lamp:
- Small amounts of condensation are normal and should dissipate.
- If significant water ingress occurs, check the seal around the lamp and ensure it's properly seated. Re-installation might be necessary.
If problems persist after checking these points, contact customer support.
6. Specifications
| Feature | Specification |
|---|---|
| Brand Name | MAGIC COLORM |
| Item Type | Day Light |
| Voltage | 12 V |
| Lumens | 3400LM |
| Material | ABS+LED |
| Certification | CCC |
| Light Colors | White (DRL), Yellow (Turn Signal), White/Halogen (Fog Lamp) |
| Waterproof Rating | IP67 |
| Lifespan | Over 50,000 hours |
6.1. Product Details

This image highlights the key components: a durable PC Lens, bright LED lights, and a robust ABS Housing.
6.2. Product Size Reference

The diagram indicates a height of approximately 11.81 inches and a width of approximately 5.9 inches for the light unit.
7. User Tips
- Pre-Installation Fitment Check: Before beginning the full installation process, it is recommended to visually check if the new light assembly fits well into your vehicle's bumper opening. This can help identify any potential fitment issues early.
8. Warranty & Support
For detailed warranty information and customer support, please refer to the official product documentation or contact the manufacturer directly.
8.1. Manufacturer Information
- Manufacturer: Guangzhou Camel Technology Co. Ltd.
- Address: No.4 West Fangxin Road, Fangcun Avenue, Liwan District, Guangzhou City, Guangdong Province
- Email: 1620477595@qq.com
8.2. EU Authorized Representative
- Representative: MJCM SAR
- Address: 78 Avenue des Champs Elysees Office 326, Paris, France
- Email: mjcm190928@gmail.com
- Contact Numbers: 0033 752907452
8.3. Importer Information
- Importer: Guangzhou Camel Technology Co. Ltd.
- Address: No.4 West Fangxin Road, Fangcun Avenue, Liwan District, Guangzhou City, Guangdong Province
- Email: 1620477595@qq.com
8.4. Additional Resources
A comprehensive user manual in PDF format is available for download or viewing: