HOMEFISH Solar Star Copper Wire Palace Lantern Lamp

Contents

HOMEFISH Solar Star Copper Wire Palace Lantern Lamp

User Instruction Manual

Introduction

Thank you for purchasing the HOMEFISH Solar Star Copper Wire Palace Lantern Lamp. This decorative solar-powered lantern is designed to provide ambient lighting for your outdoor spaces such as courtyards, gardens, villas, terraces, and more. Featuring automatic light control and a durable design, it offers an eco-friendly and convenient lighting solution.

Solar lantern glowing at dusk among fallen leaves

Image: HOMEFISH Solar Lantern providing warm illumination.

Safety Information

  • Ensure the solar panel is exposed to direct sunlight for optimal charging.
  • Do not immerse the product in water. While waterproof for outdoor use, prolonged submersion can cause damage.
  • Keep away from open flames or extreme heat sources.
  • Do not attempt to open or modify the battery compartment or internal components. This may void the warranty and cause damage.
  • Place the lantern in a stable location to prevent it from falling.

Package Contents

Please check the package for the following items:

  • 1x Solar Lantern Unit (with integrated LED lights and solar panel)
  • 1x Hanging Hook
  • 1x Ground Spike (for stake installation)

Setup Instructions

Follow these steps to set up your solar lantern:

  1. Replace the Hook: Attach the hanging hook to the top of the lantern if it's not already in place.
  2. Open the 'Cap': Gently twist or lift the top cap (containing the solar panel) to open it.
  3. Remove Isolator Tab: Locate and remove the plastic isolator tab from the battery compartment. This activates the battery.
  4. Turn On Switch: Locate the ON/OFF switch, usually underneath the solar panel cap, and slide it to the 'ON' position.
  5. Close the 'Cap': Securely close the top cap, ensuring it is properly sealed.
  6. Replace the Hook: Re-attach the hook if it was removed during the process.
  7. Pull out the Spike: If using the ground spike, extend it fully.
  8. Put in the Spike: Insert the extended spike into the bottom of the lantern.
  9. Assemble the Lamp: Ensure the spike is firmly attached to the lantern body.
  10. Complete: Your lamp is now assembled and ready for placement.
10-step visual assembly guide for the solar lantern

Image: Step-by-step visual guide for assembling the solar lantern.

Operating Instructions

The HOMEFISH Solar Lantern operates with a manual switch and automatic light control:

  • Initial Activation: Ensure the ON/OFF switch (located under the solar panel cap) is in the 'ON' position.
  • Automatic Operation: Once switched ON, the lantern will automatically charge during the day when exposed to sunlight and illuminate automatically at dusk or when it gets dark.
  • Charging: Place the lantern in a location where the solar panel receives at least 5 hours of direct sunlight daily for optimal performance.
  • Working Hours: A full charge typically provides 8-10 hours of illumination.
Diagram showing solar panel charging and smart light control

Image: Solar to Electricity conversion and Smart Light Control.

Maintenance

  • Cleaning: Periodically wipe the solar panel with a soft, damp cloth to remove dust, dirt, or debris. A clean panel ensures efficient charging.
  • Battery: The lantern uses a rechargeable Ni-MH battery. If the light output significantly decreases over time, the battery may need replacement. This should ideally be done by a qualified technician.
  • General Care: Ensure the lantern is not covered by leaves or snow, especially the solar panel, to maintain functionality.

Troubleshooting

ProblemPossible CauseSolution
Lantern does not light up at night.1. Switch is OFF.
2. Isolator tab not removed.
3. Insufficient sunlight.
4. Solar panel is dirty.
5. Battery is depleted or faulty.
1. Ensure switch is in 'ON' position.
2. Remove the plastic isolator tab.
3. Relocate lantern to a sunnier spot.
4. Clean the solar panel.
5. Allow several days of full charge; if problem persists, battery may need replacement.
Light is dim or flickers.1. Insufficient charge.
2. Battery nearing end of life.
1. Ensure full day of direct sunlight.
2. Consider battery replacement.
Light turns on/off repeatedly when moved or inverted.Internal sensor interference or loose connection.Ensure the lantern is placed upright and stable. If the issue persists, contact support.

Specifications

FeatureDetail
Product NameSolar Candle Lamp Copper Lamp
BrandHOMEFISH
Power SourceSolar
Battery2V 0.8mA/h Ni-MH battery (Included)
Light SourceLED lamp bead (Included)
Power1W
Emitting ColorWarm White
MaterialABS Plastic
Dimensions (Diameter x Height)90mm x 128mm
Solar Panel TypePolysilicon / Multi-crystalline silicon
Charging TimeApprox. 5 hours (direct sunlight)
Working TimeApprox. 8-10 hours (fully charged)
Lamp ColorBlack
Installation MethodSelf-contained (hanging or stake)
DimmableNo
CertificationsEMC, ROHS
OriginMainland China
Package Dimensions (L x W x H)14cm x 11cm x 10cm
Package Weight0.21 kg

User Tips

  • The light output is designed to be dim, providing perfect ambient lighting for a terrace or garden, rather than bright illumination.
  • These lanterns are excellent for decorative purposes, enhancing the aesthetic of windows, patios, or garden paths.
  • Ensure the solar panel is clean and unobstructed for consistent performance.

Warranty and Support

For any issues or inquiries regarding your HOMEFISH Solar Star Copper Wire Palace Lantern Lamp, please contact the seller directly through your purchase platform. Please refer to the original product listing for specific warranty details.

An additional user manual in PDF format may be available for download at: User Manual (PDF)

© 2023 HOMEFISH. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.