Aninerel ANL-4200T-24L-W-PRO

Contents

Aninerel 4200W 24V Hybrid Solar Inverter User Manual

Model: ANL-4200T-24L-W-PRO

1. Introduction

This manual describes the assembly, installation, operation, and troubleshooting of the Aninerel 4200W 24V Hybrid Solar Inverter. Please read this manual carefully before installation and operation. Keep this manual for future reference.

This unit is a hybrid solar inverter/charger designed for 4.2KVA/5.0KVA 230Vac systems. It features dual output for smart load management, lithium battery activation, a colored LCD with RGB lights, and is compatible with LiFePO4 batteries via RS485. It includes a built-in MPPT 120A solar charger, supports up to 500Vdc PV input, and is capable of working without a battery. WiFi remote monitoring is also supported.

Aninerel 4200W 24V Hybrid Solar Inverter with key specifications
Figure 1.1: Aninerel 4200W 24V Hybrid Solar Inverter highlighting 4200W Rated Power, 120A Max. Solar Charge Current, 6200W Maximum PV Input Power, and 60VDC~500VDC PV Array MPPT Voltage Range.
Product Features of Aninerel Hybrid Solar Inverter
Figure 1.2: Key product features including dual output, lithium battery activation, colored LCD with RGB lights, LiFePo4 compatibility, 500Vdc PV input, 120A MPPT, no battery mode, detachable dust cover, WiFi monitoring, multiple output priority, and EQ function.

2. Safety Instructions

WARNING: This chapter contains important safety and operating instructions. Read and keep this manual for future reference.

  1. Before using the unit, read all instructions and cautionary markings on the unit, the batteries, and all appropriate sections of this manual.
  2. CAUTION --To reduce risk of injury, charge only deep-cycle lead acid type rechargeable batteries. Other types of batteries may burst, causing personal injury and damage.
  3. Do not disassemble the unit. Take it to a qualified service center when service or repair is required. Incorrect re-assembly may result in a risk of electric shock or fire.
  4. To reduce risk of electric shock, disconnect all wirings before attempting any maintenance or cleaning. Turning off the unit will not reduce this risk.
  5. CAUTION - Only qualified personnel can install this device with battery.
  6. NEVER charge a frozen battery.
  7. For optimum operation of this inverter/charger, please follow required specifications to select appropriate cable size. It's very important to correctly operate this inverter/charger.
  8. Be very cautious when working with metal tools on or around batteries. A potential risk exists to drop a tool to spark or short circuit batteries or other electrical parts and could cause an explosion.
  9. Please strictly follow installation procedure when you want to disconnect AC or DC terminals. Please refer to the INSTALLATION section of this manual for details.
  10. Fuse is provided as over-current protection for the battery supply.
  11. GROUNDING INSTRUCTIONS -This inverter/charger should be connected to a permanent grounded wiring system. Be sure to comply with local requirements and regulations to install this inverter.
  12. NEVER cause AC output and DC input short circuited. Do NOT connect to the mains when DC input short circuits.
  13. Warning!! Only qualified service persons are able to service this device. If errors still persist after following troubleshooting table, please send this inverter/charger back to local dealer or service center for maintenance.

3. Product Overview

The Aninerel Hybrid Solar Inverter features a comprehensive design with clearly labeled components for easy installation and operation. Below is an overview of the unit's physical features and connections.

Aninerel 4.2KVA/5.0KVA Hybrid Solar Inverter with labeled components
Figure 3.1: Front, side, and bottom views of the 4.2KVA/5.0KVA model with labels for LCD display, function buttons, RGB indicator, power on/off switch, battery input, AC input, main output, second output, WiFi antenna port, RS485 communication port, grounding, and PV input.
  • LCD display: Shows operating status and input/output power information.
  • Function buttons: Used for navigation and setting adjustments.
  • RGB Indicator: Provides visual feedback on the inverter's status.
  • Power on/off switch: Controls the main power to the unit.
  • Battery input: Connection point for battery bank.
  • AC input: Connection for utility grid or generator AC power.
  • Main output: Primary AC output for loads.
  • Second output: Secondary AC output for loads.
  • WiFi antenna port: For connecting the WiFi module for remote monitoring.
  • RS485 communication port: For communication with external devices, such as LiFePO4 batteries.
  • Grounding: Essential safety connection.
  • PV input: Connection for solar PV modules.
Application Diagram for Aninerel Hybrid Solar Inverter
Figure 3.2: Application diagram showing connections for Solar Panel, Utility Grid, Generator, Battery, and various household loads like TV/Computer, Air conditioner, Refrigerator/Washing machine.

4. Setup and Installation

4.1 Unpacking and Inspection

Before installation, please inspect the unit. Be sure that nothing inside the package is damaged. You should have received the following items:

  • The unit x 1
  • User manual x 1 (PDF version available: User manual (PDF))
  • PV connector x 2
  • WiFi antenna x 1

4.2 Preparation

Before connecting all wirings, please remove the bottom cover by removing three or two screws as shown in the product overview diagram.

4.3 Mounting the Unit

Consider the following points before selecting where to install:

  • Do not mount the inverter on flammable construction materials.
  • Mount on a solid surface.
  • Install this inverter at eye level to allow the LCD display to be read at all times.
  • The ambient temperature should be between 0°C and 55°C for optimal operation.
  • The recommended installation position is to be adhered to the wall vertically.
  • Be sure to keep other objects and surfaces clear as shown in the diagram to guarantee sufficient heat dissipation and to have enough space for removing wires.

SUITABLE FOR MOUNTING ON CONCRETE OR OTHER NON-COMBUSTIBLE SURFACE ONLY.

Mounting dimensions and clearances for Aninerel Hybrid Solar Inverter
Figure 4.1: Recommended mounting dimensions and clearances (200mm top, 50cm sides, 20cm bottom) for proper heat dissipation.

Install the unit by screwing two screws. It's recommended to use M4 or M5 screws.

4.4 Battery Connection

CAUTION: For safety operation and regulation compliance, it's requested to install a separate DC over-current protector or disconnect device between battery and inverter. Please refer to the table below for typical amperage as required fuse or breaker size.

WARNING! All wiring must be performed by qualified personnel. It's very important for system safety and efficient operation to use appropriate cable for battery connection. To reduce risk of injury, please use the proper recommended cable.

Recommended Battery Cable & Terminal Size
Model Maximum Amperage Battery Capacity Wire Size Cable mm² Terminal Size (mm) L Terminal Size (mm) W Terminal Size (mm) D Torque Value
4.2KVA 175A 200AH 1AWG 50 37 15.3 6.4 4~6 Nm
5.0KVA 105A 200AH 2AWG 35 37 15.3 6.4 4~6 Nm

Follow these steps to implement battery connection:

  1. Make positive and negative cables based on recommended terminal size.
  2. Connect all battery packs as units require. It's suggested to use recommended battery capacity.
  3. Insert battery cable flatly into the battery connector of the inverter and make sure the bolts are tightened with a torque of 4~6Nm. Ensure polarity at both the battery and the inverter/charger is correctly connected and battery cables are tightly screwed to the battery connector.
Battery connection diagram for 24V model
Figure 4.2: Battery connection diagram for a 24V model using two 12V batteries in series. Includes warnings about shock hazard and proper terminal connection.

WARNING: Shock Hazard. Installation must be performed with care due to high battery voltage in series.

CAUTION!! Do not place anything between the flat part of the inverter terminal. Otherwise, overheating may occur.

CAUTION!! Do not apply anti-oxidant substance on the terminals before terminals are connected tightly.

CAUTION!! Before making the final DC connection or closing DC breaker/disconnector, be sure positive (+) must be connected to positive (+) and negative (-) must be connected to negative (-).

4.5 AC Input/Output Connection

CAUTION!! Before connecting to AC input power source, please install a separate AC breaker between the inverter and the AC input power source. This will ensure the inverter can be securely disconnected during maintenance and fully protected from overcurrent of AC input. The recommended spec of AC breaker is 50A.

CAUTION!! There are two terminal blocks with "IN" and "OUT" markings. Please do NOT mis-connect input and output connectors.

WARNING! All wiring must be performed by qualified personnel. It's very important for system safety and efficient operation to use appropriate cable for AC input connection. To reduce risk of injury, please use the proper recommended cable size as below.

Suggested Cable Requirement for AC Wires
Model Gauge Torque Value
4.2KVA 10AWG 1.4~1.6Nm
5.0KVA 10AWG 1.4~1.6Nm

Follow these steps to implement AC input/output connection:

  1. Before making AC input/output connection, be sure to open the DC protector or disconnector first.
  2. Remove insulation sleeve 10mm for six conductors. Shorten phase L and neutral conductor N by 3mm.
  3. Insert AC input wires according to polarities indicated on the terminal block and tighten the terminal screws. Be sure to connect PE protective conductor (yellow-green) first.
  4. Then, insert AC output wires according to polarities indicated on the terminal block and tighten the terminal screws. Be sure to connect PE protective conductor (yellow-green) first.
  5. Make sure the wires are securely connected.

CAUTION: Important. Be sure to connect AC wires with correct polarity. If L and N wires are connected reversely, it may cause utility short-circuited when these inverters are operated in parallel.

Detailed view of inverter bottom panel with AC input/output and other ports labeled
Figure 4.3: Detailed view of the inverter's bottom panel, showing AC input, Main out, Second out, Battery input, PV input, RS485, RS232, and Grounding connections.

CAUTION: Appliances such as air conditioners require at least 2-3 minutes to restart to balance refrigerant gas. If a power shortage occurs and recovers quickly, it can damage connected appliances. Check if your air conditioner has a time-delay function before installation. Otherwise, the inverter/charger may trigger an overload fault and cut off output, but internal damage to the air conditioner may still occur.

4.6 PV Connection

CAUTION: Before connecting to PV modules, please install separately a DC circuit breaker between the inverter and PV modules.

WARNING! All wiring must be performed by qualified personnel. It's very important for system safety and efficient operation to use appropriate cable for PV module connection. To reduce risk of injury, please use the proper recommended cable size as below.

Recommended Cable Requirement for PV Wires
Model Typical Amperage Cable Size Torque
4.2KVA 27A 10 AWG 1.4~1.6 Nm
5.0KVA 27A 10 AWG 1.4~1.6 Nm

When selecting proper PV modules, please be sure to consider these parameters:

  1. Open circuit Voltage (Voc) of PV modules must not exceed the max. PV array open circuit voltage of the inverter.
  2. Open circuit Voltage (Voc) of PV modules should be higher than the min. battery voltage.
PV Connection diagram and PV module selection parameters
Figure 4.4: PV Connection diagram illustrating solar panel integration with the inverter and house loads. Includes a table for PV module selection parameters.

PV Module Wire Connection:

Follow these steps to implement PV module connection:

  1. Remove insulation sleeve 6 mm for positive and negative conductors.
  2. Check correct polarity of connection cable from PV modules and PV input connectors. Then, connect positive pole (+) of connection cable to positive pole (+) of PV input connector. Connect negative pole (-) of connection cable to negative pole (-) of PV input connector.
  3. Make sure the wires are securely connected.

4.7 Final Assembly

After connecting all wirings, please put the bottom cover back by screwing two screws as shown in the product overview diagram.

5. Operation

5.1 Power ON/OFF

Once the unit has been properly installed and the batteries are connected well, simply press the On/Off switch (located on the side of the case) to turn on the unit.

Aninerel Hybrid Solar Inverter front view
Figure 5.1: Front view of the inverter, showing the LCD display and function buttons.

5.2 Operation and Display Panel

The operation and display panel, located on the front of the inverter, includes a LCD display, three indicators, and four function keys. These provide operating status and input/output power information.

Inverter front panel with LCD, buttons, and RGB indicator
Figure 5.2: Front panel of the inverter, highlighting the LCD display, function buttons, and RGB indicator.

RGB Indicator Messages:

Mode RGB Indicator Messages
Inverter mode Green Solid On Output is powered by battery or PV; Battery is fully charged or isn't charged.
Green Flashing Battery is charging with 2s-on and 1s-off.
AC mode Blue Solid On Output is powered by AC or PV in AC mode; Battery is fully charged or isn't charged.
Blue Flashing Battery is charging with 2s-on and 1s-off.
Standby mode Cyan Solid On Battery is fully charged or isn't charged.
Cyan Flashing Battery is charging with 2s-on and 1s-off.
Fault mode Red Solid On Fault occurs in the inverter.
Bypass mode Purple Solid On Working in AC mode without charging.
Charging mode Yellow Solid On Battery is fully charged, when switch is off.
Yellow Flashing Battery is charging, when switch is off.

Function Keys:

Function Key Description
ESC To exit setting mode.
UP To go to previous selection.
DOWN To go to next selection.
ENTER To confirm the selection in setting mode or enter setting mode.

5.3 LCD Display Description

The LCD display information can be switched by pressing the function keys. All information is shown across five areas of the LCD:

LCD display areas for Aninerel Hybrid Solar Inverter
Figure 5.3: LCD display with highlighted areas for PV data (Area 1), battery data (Area 2), AC output data (Area 3), AC input data (Area 4), and setting program code/Eco/buzzer/error/warning (Area 5).
  • Area 1: Shows PV data (voltage/current/power).
  • Area 2: Shows battery data (voltage/current/power/SOC).
  • Area 3: Shows AC-output data (voltage/current/power/percentage/frequency).
  • Area 4: Shows AC-input data (voltage/current/power/percentage/frequency).
  • Area 5: Shows setting program code/Eco/buzzer/error/warning.

LCD Data Polling Display Mode:

Simultaneously polling data: Press "UP" or "DOWN" button to show all data from area-1 to area-4 simultaneously. All data will be updated with pressing. Press the ESC key to return to the initial data.

Independent polling data: Data of areas 1-4 can be polled independently:

  1. Press "Enter" key, the circle icon of area 1 will flash. Press "UP" or "DOWN" to display data of area 1.
  2. Continue to press "Enter" key, the circle icon of area 2 will flash. Press "UP" or "DOWN" to display data of area 2.
  3. Continue to press "Enter" key, the circle icon of area 3 will flash. Press "UP" or "DOWN" to display data of area 3.
  4. Continue to press "Enter" key, the circle icon of area 4 will flash. Press "UP" or "DOWN" to display data of area 4.
  5. Continue to press "Enter" key, the circle icon of area 1 will flash, returning to area 1.

5.4 LCD Setting

After pressing and holding the "Enter" key for 3 seconds, the unit will enter setting mode. Press "UP" or "DOWN" to select setting programs. Then, press "ENTER" to confirm the selection or "ESC" to exit. In setting mode, the LCD display shows:

  • Area 5: Setting program code.
  • Area 1: Setting minimum value (if applicable).
  • Area 4: Setting maximum value (if applicable).
  • Area 2: Setting program item.
  • Area 3: Current value which can be set.

A detailed list of setting programs and their selectable options is available in the full PDF manual. Key settings include Output source priority (UTL, SOL, SBU, SUB, SUF), Maximum charging current, AC input voltage range, Battery type (AGM, Flooded, User-Defined, LI2, LI4, LIB), Auto restart options, Output voltage/frequency, Auto bypass, Maximum utility charging current, and various voltage points for battery and utility source switching.

5.5 Wi-Fi Plug Pro Quick Installation Guideline

The inverter supports Wi-Fi remote monitoring via a dedicated app. Follow these steps to set up the Wi-Fi module:

  1. Install the wireless antenna: Refer to the schematic diagram for proper installation.
  2. Download the APP: Scan the QR code provided in the manual or search for "SmartESS" in your app store (iPhone App Store; Android phone).
  3. Register: Open the APP, click "Registration", and select "Mobile phone Registration" or "Email Registration".
  4. Enable Bluetooth/WiFi: Turn on Bluetooth or WiFi on your smartphone as needed.
  5. Connect to the digital collector: Click "Toolbox" in the app and select "BLE network" or "Wi-Fi network". If choosing Bluetooth, the app will scan for nearby devices. Find the PN corresponding to your digital collector and click "Connect".
  6. Add Datalogger: Log in to your account, click the Datalogger button, tap the "+" button on the top-right, and follow prompts to enter information. The PN number is next to the machine appliance label (Initial Password: 12345678).
  7. Networking Settings: Select the corresponding 2.4G WiFi, fill in the password, and click "Start Connecting to the Network".
Aninerel Hybrid Solar Inverter with smartphone app for monitoring
Figure 5.4: The inverter being monitored and controlled via a smartphone application using WiFi.
Diagram showing solar energy feeding into the grid
Figure 5.5: Illustration of the inverter's grid-tie capability, where solar energy can be fed into the state grid.

6. Maintenance

6.1 Battery Equalization

The equalization function is integrated into the charge controller to reverse the buildup of negative chemical effects like stratification and remove sulfate crystals from battery plates. This helps maintain overall battery capacity and extends lifecycle. It is recommended to equalize batteries periodically.

How to Apply Equalization Function:

You must enable the battery equalization function in monitoring LCD setting program 33 first. Then, you may apply this function by either of the following methods:

  1. Setting equalization interval in program 37.
  2. Active equalization immediately in program 39.

When to Equalize:

In the float stage, when the setting equalization interval (battery equalization cycle) is reached, or equalization is activated immediately, the controller will start to enter the Equalize stage.

Equalize Charging Time and Timeout:

In the Equalize stage, the controller will supply power to charge the battery as much as possible until the battery voltage raises to the battery equalization voltage. Then, constant-voltage regulation is applied to maintain the battery voltage at the equalization voltage. The battery will remain in the Equalize stage until the setting battery equalized time is reached.

However, if the battery equalized time expires and the battery voltage doesn't rise to the battery equalization voltage point, the charge controller will extend the battery equalized time until the battery voltage achieves the battery equalization voltage. If the battery voltage is still lower than the battery equalization voltage when the battery equalized timeout setting is over, the charge controller will stop equalization and return to the float stage.

6.2 Setting for Lithium Battery

If using a lithium battery with the inverter, ensure it is a compatible model. There are two connectors on the lithium battery: the RS485 port of the BMS and the power cable.

Lithium Battery Connection:

  1. Assemble battery terminals based on recommended battery cable and terminal size (same as Lead acid, see section Battery Connection for details).
  2. Connect the end of the RS485 port of the battery to the BMS (RS485) communication port of the inverter.

Lithium Battery Communication and Setting:

If choosing a lithium battery, make sure to connect the BMS communication cable between the battery and the inverter. This cable delivers information and signals between the lithium battery and the inverter, allowing for:

  • Re-configuring charging voltage, charging current, and battery discharge cut-off voltage according to the lithium battery parameters.
  • The inverter to start or stop charging according to the status of the lithium battery.

Make sure the lithium battery RS485 port connects to the inverter is Pin to Pin. The communication cable is typically included in the package. The inverter RS485 port pin assignment is as follows:

RS485 Port Pin Assignment
Pin Number RS485 Port
PIN1 RS485-B
PIN2 RS485-A
PIN7 RS485-A
PIN8 RS485-B

LCD Setting for Lithium Battery:

After connecting, you need to finish and confirm some settings:

  1. Select program 05 as lithium battery type.

If communication between the inverter and battery is successful, information from the BMS will be shown on the LCD:

  • Communication successful icon: 'Li' will be flashing.
  • Max lithium battery charging voltage.
  • Max lithium battery charging current.
  • Lithium battery discharging is forbidden: 'Li' will flash once every 1 second.
  • Lithium battery charging is forbidden: 'Li' will flash once every 2 seconds.
  • Lithium battery SOC (%).

Setting for Lithium Battery Without Communication:

This suggestion is for lithium battery applications without communication to avoid BMS protection. Follow these settings:

Recommended method 1: Set battery type as "LIB" in program 05.

Recommended method 2: Setting as follows:

  1. Before starting setting, obtain the battery BMS specification (Max charging voltage, Max charging current, Discharging protection voltage).
  2. Set battery type as "LIB" in program 05.
  3. Set C.V voltage as Max charging voltage of BMS-0.5V in program 26.
  4. Set floating charging voltage as C.V voltage in program 27.
  5. Set Low DC cut-off voltage (discharging protection voltage) in program 29.
  6. Set Max charging current in program 02, which must be less than the Max charging current of BMS.
  7. Set voltage point back to utility source when selecting "SBU priority" in program 12.

The setting value must be ≥ Low DC cut-off voltage + 2V, or else the inverter will show a warning for low battery voltage.

Remark:

  1. It is recommended to finish setting without turning on the inverter (just let the LCD show, no output).
  2. When you finish setting, please restart the inverter.

7. Troubleshooting

This section provides guidance for common issues and their solutions. If problems persist, contact qualified service personnel.

7.1 Fault Reference Code

Fault Code Fault Event
01Over temperature of inverter module
02Over temperature of DCDC module
03Battery voltage is too high
04Over temperature of PV module
05Output short circuited.
06Output voltage is too high.
07Overload time out
08Bus voltage is too high
09Bus soft start failed
10PV over current
11PV over voltage
12DCDC over current
13Over current or surge
14Bus voltage is too low
15Inverter failed (Self-checking)
18Op current offset is too high
19Inverter current offset is too high
20DC/DC current offset is too high
21PV current offset is too high
22Output voltage is too low
23Inverter negative power
24Op2 current offset is too high

7.2 Warning Indicator

Warning Code Warning Event Audible Alarm
02Temperature is too HighBeep three times every second
04Low batteryBeep once every second
07OverloadBeep once every 0.5 second
10Output power deratingBeep twice every 3 seconds
14Fan blockedNone
15PV energy is lowBeep twice every 3 seconds
19Lithium Battery communication is failedBeep once every 0.5 second
21Lithium Battery over currentNone
22The load exceeds the set value of program 47None
E9Battery equalizationNone
bPBattery is not connectedNone

7.3 General Troubleshooting Steps

Problem LCD/LED/Buzzer Explanation / Possible cause What to do
Unit shuts Down automatically during startup process. LCD/LEDs and buzzer active for 3 seconds then off. The battery voltage is too low. 1. Re-charge battery.
2. Replace battery.
No response after power on. No indication. 1. Battery voltage is far too low.
2. Battery polarity is connected reversed.
1. Check if batteries and wiring are connected well.
2. Re-charge battery.
3. Replace battery.
Input voltage displayed as 0 on LCD, green LED flashing. Input protector is tripped. Check if AC breaker is tripped and AC wiring is connected well.
Mains exist but unit works in battery mode. Green LED is flashing. Insufficient quality of AC power (Shore or Generator). Check if AC wires are too thin and/or too long. Check if generator (if applied) is working well or if input voltage range setting is correct (UPS / Appliance).
Green LED is flashing. Set "Solar First" as priority of output source. Change output source priority to Utility first.
When unit is turned on, internal relay switches on and off repeatedly. LCD display and LEDs are flashing. Battery is disconnected. Check if battery wires are connected well.
Fault code 07 Overload error. Inverter is overload 110% and time is up. Reduce the connected load by switching off some equipment.
Fault code 05 Output short circuited. Check if wiring is connected well and remove abnormal load.
Fault code 02 Internal temperature of inverter component is over 100°C. Check whether the air flow of the unit is blocked or whether the ambient temperature is too high.
Buzzer beeps continuously and red LED is on. Fault code 03 Battery is over-charged. Return to repair center.
The battery voltage is too high. Check if spec and quantity of batteries meet requirements.
Fault code 06/22 Output abnormal (Inverter voltage below 190Vac or higher than 260Vac). 1. Reduce the connected load.
2. Return to repair center.
Fault code 08/09/15 Internal components failed. Return to repair center.
Fault code 13 Over current or surge. Restart the unit. If error happens again, return to repair center.
Fault code 14 Bus voltage is too low. If wires are connected well, return to repair center.
Another fault code If the wires are connected well, please return to repair center.

8. Specifications

8.1 Table 1 Line Mode Specifications

INVERTER MODEL 4.2KVA 5.0KVA
Input Voltage WaveformSinusoidal (utility or generator)
Nominal Input Voltage230Vac
Low Loss Voltage170Vac±7V (UPS); 90Vac±7V (Appliances)
Low Loss Return Voltage180Vac±7V (UPS); 100Vac±7V (Appliances)
High Loss Voltage280Vac±7V
High Loss Return Voltage270Vac±7V
Max AC Input Voltage300Vac
Nominal Input Frequency50Hz / 60Hz (Auto detection)
Low Loss Frequency40±1Hz
Low Loss Return Frequency42±1Hz
High Loss Frequency65±1Hz
High Loss Return Frequency63±1Hz
Output Short Circuit ProtectionBattery mode: Electronic Circuits
Efficiency (Line Mode)>95% (Rated R load, battery full charged)
Transfer Time10ms typical (UPS); 20ms typical (Appliances)

8.2 Table 2 Inverter Mode Specifications

INVERTER MODEL 4.2KVA 5.0KVA
Rated Output Power4.2KVA / 4.2KW5.0KVA / 5.0KW
Dual output functionYesYes
Max. main output power4.2KVA5.0KVA
Max. second output power4.2KW5.0KW
Output Voltage WaveformPure Sine Wave
Output Voltage Regulation230Vac±5%
Output Frequency50Hz or 60Hz
Peak Efficiency94%
Surge Capacity2* rated power for 5 seconds
Nominal DC Input Voltage24Vdc48Vdc
Cold Start Voltage23.0Vdc46.0Vdc
Low DC Warning Voltage (Just for AGM and Flooded @ load < 20%)22.0Vdc44.0Vdc
Low DC Warning Voltage (Just for AGM and Flooded @ 20% ≤ load < 50%)21.4Vdc42.8Vdc
Low DC Warning Voltage (Just for AGM and Flooded @ load ≥ 50%)20.2Vdc40.4Vdc
Low DC Warning Return Voltage (Just for AGM and Flooded @ load < 20%)23.0Vdc46.0Vdc
Low DC Warning Return Voltage (Just for AGM and Flooded @ 20% ≤ load < 50%)22.4Vdc44.8Vdc
Low DC Warning Return Voltage (Just for AGM and Flooded @ load ≥ 50%)21.2Vdc42.4Vdc
Low DC Cut-off Voltage (Just for AGM and Flooded @ load < 20%)21.0Vdc42.0Vdc
Low DC Cut-off Voltage (Just for AGM and Flooded @ 20% ≤ load < 50%)20.4Vdc40.8Vdc
Low DC Cut-off Voltage (Just for AGM and Flooded @ load ≥ 50%)19.2Vdc38.4Vdc

8.3 Table 3 Charge Mode Specifications

Utility Charging Mode 4.2KVA 5.0KVA
Max Charging Current (PV+AC) (@ VI/P=230Vac)100Amp100Amp
Max Charging Current (AC) (@ VI/P=230Vac)80Amp60Amp
Bulk Charging Voltage (Flooded Battery)29.2Vdc58.4Vdc
Bulk Charging Voltage (AGM / Gel Battery)28.2Vdc56.4Vdc
Floating Charging Voltage27Vdc54Vdc
Overcharge Protection32Vdc63Vdc
Battery reverse connection protectionNoNo
Charging Algorithm3-Step

8.4 Table 4 General Specifications

INVERTER MODEL 4.2KVA 5.0KVA
Operating Temperature Range-10°C to 55°C
Storage temperature-15°C~60°C
Humidity5% to 95% Relative Humidity (Non-condensing)
Dimension (D*W*H), mm368x312x105
Net Weight, kg6.79.3

9. User Tips

  • Always ensure proper ventilation around the inverter to prevent overheating, especially during high load operation.
  • Regularly check battery connections for tightness and corrosion to maintain optimal performance and safety.
  • Utilize the Wi-Fi monitoring feature to keep track of your system's performance and battery status remotely.
  • For optimal battery health, consider implementing the battery equalization function periodically, especially for lead-acid batteries.
  • When configuring settings, double-check all parameters, particularly for battery type and voltage cut-offs, to match your specific battery bank.

10. Warranty and Support

For warranty information, please refer to the terms and conditions provided at the time of purchase or contact your authorized Aninerel dealer. Keep your purchase receipt as proof of purchase.

If you encounter any issues not covered in the troubleshooting section or require technical assistance, please contact Aninerel Official Store customer support or a qualified service center.

For further details, you may also refer to the official user manual PDF: Aninerel Hybrid Solar Inverter User Manual (PDF).


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.