1. Introduction
This manual provides essential information for the safe and efficient use of your DC12V Geared Motor, Model 5840-31ZY. Please read these instructions carefully before installation and operation to ensure optimal performance and longevity of the product.
2. Safety Information
- WARNING: To avoid danger of suffocation, keep any plastic packaging away from babies and children.
- Ensure the power supply matches the motor's specified voltage (DC12V). Connecting to an incorrect voltage or AC power can damage the motor and governor.
- Always disconnect power before performing any installation, wiring, or maintenance.
- Avoid touching moving parts during operation.
- Do not operate the motor in wet conditions or environments with flammable gases or liquids.
3. Product Overview
The 5840-31ZY Geared Motor is a DC12V turbo worm speed reduction motor designed for various applications requiring controlled speed and high torque. It comes with a governor for speed and direction control.
Package Contents:
- 1 x DC12V Geared Motor (Model 5840-31ZY)
- 1 x CCM2 Motor Governor
- 1 x CW and CCW Switch (for forward, reverse, and stop)
- 1 x Potentiometer with Knob Cap (for speed control)
- 1 x Washer
- 1 x Mounting Bracket
- 4 x Mounting Screws

Figure 3.1: Complete product package including motor, governor, switch, and mounting hardware.

Figure 3.2: Close-up view of the motor, governor board, and potentiometer.
4. Setup and Installation
4.1 Motor Installation
- Secure the motor using the provided mounting bracket and screws. Ensure the motor is firmly attached to a stable surface to prevent vibration and movement during operation.
- Ensure the 8mm output shaft is clear of obstructions and can rotate freely.

Figure 4.1: The L-shaped mounting bracket for securing the motor.
4.2 Wiring Instructions
Carefully follow the wiring diagram below. Incorrect wiring can damage the components.
- Connect the Motor: Connect the motor's two wires to the 'OUT' terminals on the governor board.
- Connect Power Supply: Connect your DC12V power supply to the 'IN' terminals on the governor board. Ensure the positive (+) terminal of the power supply connects to the positive terminal on the governor, and the negative (-) terminal connects to the negative terminal.
- Connect Potentiometer: The potentiometer is pre-wired and connects to the white connector on the governor board. This controls the motor speed.
- Connect CW/CCW Switch: The CW/CCW switch is typically wired in line with the motor or power supply to control direction and stop. Refer to the specific switch's wiring for integration.

Figure 4.2: Wiring connections for the governor board. 'OUT' for motor, 'IN' for power supply.

Figure 4.3: Governor board showing CW and CCW indicators, and Power On indicator.
Important Wiring Notes:
- The input to the motor speed controller (governor) is direct current (DC) only. Do NOT connect it directly to alternating current (AC) sources like household 220V AC.
- Ensure the positive and negative poles of the DC power supply are connected correctly; polarity reversal will damage the governor.
- The motor itself can run in either direction. If the initial running direction is not suitable, you can change it by reversing the motor's wire connections to the 'OUT' terminals.
5. Operating Instructions
- Power On: Once wired correctly, apply DC12V power. The 'Power On' indicator on the governor board should light up.
- Direction Control: Use the CW/CCW switch to select the desired rotation direction (Clockwise, Counter-Clockwise) or to stop the motor. The CW and CCW indicators on the governor board will show the active direction.
- Speed Control: Rotate the potentiometer knob to adjust the motor's speed. Turning the knob clockwise typically increases speed, and counter-clockwise decreases it.
- Self-Locking Feature: The turbine worm motor has a self-locking mechanism when power is off, meaning the output shaft will hold its position and resist external rotation.
This geared motor is suitable for various applications such as curtain machines, billboards, and window openers due to its strong torsion and speed reduction capabilities.
6. Maintenance
- Storage: Do not store the motor in high temperature or extreme humidity. Avoid placing it in corrosive gas environments, as this can reduce the motor's effectiveness and lifespan.
- Operation: Ensure there are no restrictions on the motor's rotation. Adhesives or foreign materials should not flow into the bearing through the rotating shaft.
- Overload Prevention: To prolong service life, do not overload the motor or hang objects that hinder rotation at the shaft end. Avoid manufacturing eccentric heavy radiation loads, which are harmful to motor life.
- Gear Capacity: The maximum bearing capacity of the gear is 70KG. Blocking the motor is forbidden, and prolonged blocking may cause the motor to burn out.
- Soldering: If soldering is required on the motor terminals, use a soldering iron temperature of 340℃±40℃, and keep heating time less than 3 seconds. Avoid deforming plastic parts or allowing solder to flow into the motor.
- Power Supply: Always supply the specified DC12V power and ensure it is within the measurable requirements.
- Installation: When installing pulleys or gears, avoid abnormal force or impact. Ensure mounting screws are not excessively long, as this can cause contact between the motor and rotor, affecting performance.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Motor does not run | No power supply; Incorrect wiring; CW/CCW switch in 'Stop' position; Faulty governor/motor | Check power connection and voltage; Verify wiring according to diagram; Ensure switch is in 'CW' or 'CCW'; Test components if possible |
| Motor runs slowly or inconsistently | Low voltage; Potentiometer set too low; Overload; Obstruction | Check power supply voltage; Adjust potentiometer; Reduce load; Remove any obstructions |
| Motor overheats | Overload; Prolonged blocking; Insufficient ventilation | Reduce load; Avoid blocking the motor; Ensure adequate airflow around the motor |
| Excessive noise during operation | Loose mounting; Obstruction in gears; Worn bearings | Tighten mounting screws; Check for and remove obstructions; If noise persists, contact support |
8. Specifications
8.1 Motor Specifications (Model: 5840-31ZY)
- Working Voltage: DC12V
- Shaft Length: Approx. 15mm / 0.6in (D shaft length approx. 13mm / 0.5in)
- Shaft Diameter: Approx. 8mm / 0.3in (D shaft)
- Output Power: 735-746W
- Type: Gear Motor
- Protect Feature: Waterproof
- Certification: NONE
| Voltage (V) | Rated Speed (RPM) | Rated Torsion (Kg.cm) | Rated Current (A) | Maximum Torsion (Kg.cm) | Stall Current (A) |
|---|---|---|---|---|---|
| 12 | 400 | 3.4 | ≤1.6 | 8.5 | 6.5 |
| 12 | 200 | 6.2 | ≤1.6 | 16 | 6.5 |
| 12 | 130 | 10 | ≤1.6 | 25 | 6.5 |
| 12 | 50 | 20 | ≤1.6 | 50 | 6.5 |
| 12 | 30 | 40 | ≤1.6 | 70 | 6.5 |
| 12 | 20 | 60 | ≤1.6 | 70 | 6.5 |
| 12 | 12 | 70 | ≤1.6 | 70 | 6.5 |
| 12 | 10 | 70 | ≤1.6 | 70 | 6.5 |
8.2 CCM2 Motor Governor Parameters
- Model: CCM2
- Working Voltage: DC10V-30V
- Control Power: 12V x 3A=36W, 24V x 3A=72W, >24V, maximum 120W
- Rated Current: 3A
- Maximum Current: 5A
- PWM Pulse Width Adjustment Range: 5%-95%
- Potentiometer: Resistance value B10K, wire length approx. 20cm / 7.9in, opening approx. 8mm / 0.3in
- Output Voltage: About 0-100 percent of the input voltage
- Speed Governor Size: Approx. 74 x 47 x 28mm / 2.9 x 1.9 x 1.1in

Figure 8.1: Dimensions of the governor board, potentiometer, and CW/CCW switch.
9. User Tips
- Always double-check your wiring before applying power to prevent damage to the motor or governor.
- For applications requiring precise speed, ensure your power supply is stable and free from voltage fluctuations.
- Mount the motor securely to minimize vibration, which can lead to premature wear and increased noise.
- Avoid running the motor at a continuous stall (zero RPM under load) as this can cause rapid heat buildup and damage.
10. Warranty and Support
For technical support, warranty claims, or further inquiries, please contact the manufacturer or your point of purchase.
Manufacturer Information:
- Company Name: Tai'an Anbang International Trade Co., Ltd
- Full Address: No.959 North Tianmen Street, Tai'an High tech Development Zone, Shandong, China, Tai'an Shandong Province
- Email: 2777053327@qq.com
- Telephone: 86-13076837746
EU Authorized Representative:
- AR Company Name: Kequ Technology s.r.o.
- Full Address: Pražákova 1008/69, Štyřice, 63900 Brno, South Moravian Region, Czech Republic
- Email: christopher25106@outlook.com
- Telephone: 420-123456789