FEELWORLD WTRS

Contents

FEELWORLD WTRS 4K Wireless Video Transmission System User Manual

Model: WTRS

Foreword

Thank you for purchasing the FEELWORLD WTRS/WTRH wireless video transmission system. This system is equipped with a TX/RX set that integrates intercom, recording, and live streaming capabilities. With a 10Mbps high data rate, SDI (for WTRS) and HDMI ports, and other features built for professional filmmaking, it empowers filmmakers, crews, and content creators. Please read this manual carefully before using the product.

Important Cautions

  • Do not expose this device to extreme hot, cold, dusty, or humid environments.
  • Do not scratch the device with sharp objects.
  • Do not drop this device from a high place, as this may cause hardware damage.
  • This device is designed for non-water proofing. Do not allow any liquid to penetrate into the device.
  • Do not attempt to dismantle, open, or repair this device by non-technical personnel, as this may cause permanent damage to the device.

Key Features

  • Both TX (Transmitter) and RX (Receiver) support recording; RX also supports playback, fast forward, and fast backward.
  • HDMI & SDI (optional) signal interfaces.
  • Transmission range up to 1000ft (300m) with ultra-low latency of 0.08S.
  • Supports up to 4K30Hz video.
  • UVC streaming for convenient and smoother live streaming.
  • The transmitter can be switched as a receiver at will.
  • Wireless full-duplex talkback for real-time intercom between the director and the photographer.
  • One TX can connect to multiple RX units.
  • Supports APP monitoring for Android/iOS systems.
  • Features 13 frequency channels with smart channel scan.

Setup Guide

Installation Instruction

Follow these steps for proper installation of your WTRS system:

  1. Connect the transmitter (TX) to your camera's video output (HDMI OUT or SDI OUT).
  2. Connect the receiver (RX) to your monitor's video input (HDMI IN or SDI IN).
  3. Power the units using NP-F batteries or a USB-C 5V/3A power source.
  4. For optimal reception, install the transmitter 1.7+ meters high from the ground and the receiver 2+ meters high from the ground. Ensure the best reception angle by facing the transmitter and receiver towards each other.
WTRS Installation Diagram
Diagram illustrating the setup of the WTRS system with a camera, monitor, and power sources, showing recommended heights for TX and RX units.
WTRS Real-time Monitoring Setup
Example of a real-time video monitoring and recording setup using the FEELWORLD WTRS system.
WTRS Mounting Options
Various mounting options for the WTRS transmitter and receiver, including on camera arms, cold shoes, and monitors, utilizing 1/4" screw holes.

Operating Instructions

Port Instruction (WTRS Example)

Familiarize yourself with the ports and buttons on both the Transmitter (TX) and Receiver (RX) units.

WTRS Product Overview and Ports
Detailed product overview showing the various ports and controls on the Transmitter (TX) and Receiver (RX) units, along with the packaging list.

Transmitter (TX) Ports:

  • 1: Antenna Ports
  • 2: Record Button
  • 3: Display (OLED screen)
  • 4: 5-direction Button (Menu control)
  • 5: Menu return/exit
  • 6: Type-C Power Port
  • 7: TF Card Slot
  • 8: 1/4" Screw Hole
  • 9: HDMI Signal Output
  • 10: HDMI Signal Input
  • 11: SDI Signal Input
  • 12: 3.5mm Earphone Port
  • 13: Power ON/OFF
  • 14: Battery Release Button
  • 15: NP-F Battery Slot
  • 16: 1/4" Screw Hole

Receiver (RX) Ports:

  • 1: Antenna Ports
  • 2: Record Button
  • 3: Display (OLED screen)
  • 4: 5-directional Button (Menu control)
  • 5: Menu return/exit
  • 6: Type-C Power Port
  • 7: TF Card Slot
  • 8: 1/4" Screw Hole
  • 9: UVC Streaming Output
  • 10: HDMI Signal Output
  • 11: SDI Signal Output
  • 12: 3.5mm Earphone Port
  • 13: Power ON/OFF
  • 14: Battery Release Button
  • 15: NP-F Battery Slot
  • 16: 1/4" Screw Hole
WTRS TX and RX Ports Diagram
Detailed diagrams of the Transmitter (TX) and Receiver (RX) units highlighting their respective input and output ports for SDI, HDMI, and UVC.

Flexible Power Options

Both the TX and RX units are equipped with a USB-C power input and an NP-F battery slot. You can use a 5V/3A USB-C power source or NP-F batteries (excluding) to power the devices.

WTRS Flexible Power Options
Illustration of the RX unit showing the USB-C 5V/3A power input and the NP-F battery slot for flexible power solutions.

UI Instruction

1. Startup

The startup screen will display the FEELWORLD logo. Once the device runs, the main menu will appear.

2. Running Interface

The running interface displays information such as channel, device type (TX/RX), link status, signal strength, video format, intercom mode, battery level, temperature, fan status, and group display.

WTRS OLED Display
Close-up of the RX unit's OLED display, showing battery level, signal strength, current channel (CH 01 A), device type (RX), link status (Link OK), resolution (1080P60), and temperature (39°C) with fan status.

Channel Switch: Use the 5-directional button (up/down or left/right) to select the channel, then press the middle of the button to confirm.

3. Menu Navigation

Press and hold the 5-directional button for about 2 seconds to enter the menu. Use the 5-directional button (up/down or left/right) to select a menu item, then press the middle button to confirm. To select a function within a menu, use the 5-directional button (up/down or left/right) and confirm with the middle button. Press the return/exit button to go back or exit the menu.

  • Device (Transmitter only): Switch between TX (transmitter) and RX (receiver) manually.
  • Intercom: Switch between Full Duplex, TD mode (TD speak, Cameraman listen), or OFF (turn off intercom).
  • Fan Status: Adjust the fan level or turn it off manually (default is Auto).
  • About us: Check telephone and website information.
  • Language: Select English or Chinese.
  • WIFI_SSDI: Shows device name and password.
  • Version: Displays the device's version number.
  • WLAN (TX): Displays Wifi name (SSID) and password.
  • WLAN (RX): Select PassWD to display Wifi name and password (RX needs to connect with TX first). Select Scan to automatically scan for high-quality channels.
  • SD Card: If recording is not possible, format the TF (micro SD) card here.
  • Working Mode: Includes Pairing and Grouping.

Pairing and Grouping

Pairing Mode: Manually pair devices. One transmitter can pair with up to 4 receivers. Turn on WPS on both TX and RX simultaneously, then turn off receivers that have finished pairing. Use the same method to add more receivers. Finally, turn on all paired devices.

Grouping Mode: TX and RX can be paired automatically. Set TX and RX to the same group and channel (e.g., TX is A CH03, RX is A CH03) for automatic connection.

WTRS Preset Grouping and Pairing
Diagram illustrating the preset grouping and pairing feature, showing a Transmitter (TX) unit connected to multiple Receiver (RX) units within 'Group A Channel 01'.

Record & Playback Instruction

Both TX and RX support real-time recording, and RX also supports playback, fast forward, and fast backward.

  1. Ensure both TX and RX have signal input, and the HDMI OUT of RX is connected to a display.
  2. Insert a TF card into the TF card slot. Press the "REC" button to start recording.
  3. Press the "REC" button again to finish recording and save the file.
  4. To playback, press and hold the "REC" button until the saved record files display. Use the 5-directional button to select the desired file and press the middle button to play.
  5. To delete a record file, gently press the "REC" key to display the deletion option. Toggle the 5-directional key to select "OK" and press the center button to confirm deletion.
  6. During playback, use the 5-directional button to fast forward or fast backward. Press the middle button to pause.
WTRS One Key Record
Close-up of the RX unit showing the 'REC' button and OLED display, indicating the one-key record function for instant footage capture.
WTRS Instant Playback
A user reviewing recorded content on a monitor connected to the WTRS RX unit, demonstrating the instant playback feature for on-site checking of footage.

Streaming Instruction (UVC Streaming)

The receiver (RX) unit's UVC OUT port can be used as a webcam source. It can be recognized by live streaming platforms like Zoom, YouTube, Facebook, Twitch, OBS, etc.

OBS Streaming

WTRS/WTRH is compatible with many third-party streaming software. OBS is recommended and can be downloaded from obsproject.com/download.

  1. Click the "+" icon in OBS to add a source.
  2. Choose "Video Capture Device".
  3. Select "FEELWORLD" as the device and choose "YUY2" for Video Format, or use the device default. The maximum resolution is 3840x2160.
  4. Audio Setting: If there is no audio, check the video source settings and OBS audio settings. Set Default for the audio source. In OBS, go to Settings > Audio and choose the audio device (Mic/Auxiliary Audio Device).
  5. Synchronize Video with External Audio: If the video lacks embedded audio, right-click the Video Capture Device in Source, choose Filter, click "+" under Audio/Video Filters, and select "Video Delay (Async)". Input the delay value in milliseconds until video and audio are synchronous.
  6. Streaming Setting: Find the RTMP URL and Stream Key from your broadcast website. In OBS, go to Settings > Stream. Choose "Streaming Service" or "Custom Streaming Server". If using Custom Service, fill in the URL and Stream Key. Click "Start Streaming".
WTRS UVC Streaming Workflow
Diagram illustrating the UVC streaming workflow: Camcorder > WTRS TX > WTRS RX > Computer > OBS > Streaming Platform (YouTube, Facebook, TikTok, Instagram).

vMix Streaming

  1. Click a new blank in vMix, then click "Add Input".
  2. Select "Camera" > "Camera" > "FEELWORLD".
  3. Select the same resolution as the output and click "OK".
  4. Click the "Stream" setting button.
  5. Complete the URL and Key information. Click "Start 1" to begin streaming.

Note: vMix does not support automatic recognition of the output resolution of WTRS/WTRH. Every time the output resolution is modified, the picture on vMix will pause. You need to re-select FEELWORLD and manually input the current output resolution.

APP Operation Instruction

1. APP Download

iOS APP: Search "feelworld wireless 2" on the App Store.

Android APP: Search "feelworld wireless 2" on Google Play. (Note: Currently, only monitoring functions are available on Android APP; recording and other functions like waveform, histogram are under development).

You can also scan the QR code to download the app.

2. Connect Smart Devices to Transmitter

When first using, power on the transmitter. On your smartphone/tablet, go to Setting > Wireless & networks, select the transmitter's name (e.g., FEELWORLD_5G_XXXXX), and input the password (e.g., 12345678). Click "join" to connect. Then, open the APP and click "Go" to enter the monitoring interface.

3. APP Operation (e.g., iOS system)

  1. Click the icon to pop up all monitoring auxiliary functions.
  2. Click on a corresponding monitoring function to add it to the top of the screen as a shortcut bar.
  3. After adding, all functions will be displayed at the top. Clicking on a function can quickly turn it on or off.

Function Settings and Instructions (APP)

  • All Waves: Displays waveform, vector, and histogram.
  • Waveform: Assists with exposure calibration and checks lighting evenness.
  • Vector: Shows image saturation and pixel color spectrum.
  • Histogram: RGB Histogram displays color tone distribution and exposure status. Y Histogram checks picture brightness.
  • Focus Assist: Highlights in-focus areas.
  • Exposure Tips: Highlights overexposed areas with a striped pattern.
  • False Colors: Depicts objects in colors different from a true color image.
  • Monochrome Display: Adjusts hue and saturation quickly.
  • LUT (Look Up Table): Quickly applies color data and styles. Built-in 4 LUTs (SLOG2, LOGC, SLOG3, VLOG).
  • Deformation Mode: Allows viewing unsqueezed images from anamorphic lenses.
  • Nine Grid: Divides the picture into equal grids.
  • Center Mark: Displays a center mark.
  • Safety Frame: Displays safety frames (70%, 80%, 90%, 16:9, 16:10, 1.85:1, 2.35:1).
  • Mask Mark: Displays mask marks (16:9, 16:10, 4:3, 5:4, 1.85:1, 2.35:1).
  • Image Flip: Flips the image (T&B, L&R, ALL).
  • Scan Mode: Toggles between "Under Scan" and "Over Scan".
  • Pixel to Pixel: Checks image detail from a 1:1 signal source without scaling.
  • Image Freeze: Freezes the image.
  • Image Overlay: Overlays a screenshot image from the APP.
  • Audio Column: Provides numerical indicators and headroom levels.
  • Record: Initiates recording.
  • Recorded Video Pop-up: Displays recorded videos.

Full Duplex Intercom

The WTRS features an intercom function, enabling real-time communication between the director and the photographer, saving time and costs compared to setting up an extra intercom system.

WTRS Full Duplex Intercom
Two individuals on a film set using the FEELWORLD WTRS system for full duplex intercom communication, demonstrating real-time interaction between director and photographer.

One Transmitter to Four Receivers

The WTRS supports WPS pairing manually, allowing one transmitter to connect to up to four receivers with stable signals. This offers greater flexibility for additional monitoring needs on set.

WTRS One TX to Four RX
An on-set scenario showing a single WTRS Transmitter (TX) broadcasting to multiple Receiver (RX) units, illustrating the capability for one transmitter to connect to four receivers for expanded monitoring.

Smart Channel Scan

The receiver comes with a smart channel scan function, which helps determine which channels are occupied and selectable, ensuring optimal signal quality.

WTRS Smart Channel Scan
The OLED display of the RX unit showing the results of a smart channel scan, indicating available and occupied channels (e.g., CH 01-13 with checkmarks for available and 'x' for occupied).

Flexible Fan Control

The WTRS offers a fan cooling system with different fan modes for various scenarios. It defaults to automatic adjustment based on temperature for effective heat dissipation. You can also manually adjust the fan speed or turn it off for a noise-free environment.

WTRS Flexible Fan Control
Illustration of the RX unit highlighting its flexible fan control feature with options for Auto Mode (automatic adjustment), Manual Mode (manual adjustment), and OFF (for audio-critical scenarios).

Troubleshooting (Common Problems)

  1. Mosaic Screen or Unstable Signal Connection: This usually indicates a nearby Wi-Fi signal interfering with the transmission frequency. Re-select another channel. (Note: Only the receiver is allowed to adjust the channel).
  2. Transmitter and Receiver Cannot Connect in Pairing Mode: Turn off both the transmitter and receiver, then turn them on again simultaneously. Activate WPS mode on both to re-pair.
  3. Weak Signal Frequency: Try choosing another channel with a wider frequency span. For instance, if channel 8 has a weak signal, try channel 1 or 5 instead of 7 or 9.
  4. Poor Wi-Fi Reception on Mobile Phone: This can be related to the brand and model of the mobile phone. Try using different mobile phones.

Specifications (Parameter)

TransmitterReceiver
ScreenOLEDOLED
Interface1* SDI input (optional)
1* HDMI input, 1* HDMI output
2* Antenna port (RP-SMA Male)
USB-C power input
3.5mm headphone jack
TF (micro SD) Card Slot
1* SDI output (optional)
1* HDMI output
1* UVC out
2* Antenna port (RP-SMA Male)
USB-C power input
3.5mm headphone jack
TF (micro SD) Card Slot
Power Supply Way/Voltage RangeNP-F battery slot, Type-C: 5V/3ANP-F battery slot, Type-C: 5V/3A
Power Consumption<4.4W<6.4W
HDMI Input/Output Video Format480P60, 576P60
720P60/59.94/50
1080P60/59.94/50/30/29.97/25/24/23.98
1080I60/59.94/50
2160P30/25/24
HDMI Type A
480P60, 576P60
720P60/59.94/50
1080P60/59.94/50/30/29.97/25/24/23.98
1080I60/59.94/50
2160P30/25/24
HDMI Type A
SDI Input/Output Video Format480P60, 576P60
720P60/59.94/50
1080P60/59.94/50/30/29.97/25/24/23.98
1080I60/59.94/50
1*BNC
480P60, 576P60
720P60/59.94/50
1080P60/59.94/50/30/29.97/25/24/23.98
1080I60/59.94/50
1*BNC
Frequency5.1-5.9GHz5.1-5.9GHz
Modulation ModeOFDMOFDM
Transmission Power22dBm/
Receiving Sensitivity/-87dBm
Bandwidth20/40MHz20/40MHz
LatencyMin 0.08SMin 0.08S
Intercom Frequency Response Range20Hz~20KHz20Hz~20KHz
Recording FormatMP4MP4
TF (micro SD) card storage capacityMax support 256GMax support 256G
Operating Temperature0°C ~ 40°C0°C ~ 40°C
Storage Temperature-20°C ~ 60°C-20°C ~ 60°C
Unit Size (mm) (excluding antenna)81.87L*28.1W*120.5H81.87L*28.1W*120.5H
Unit Weight126g126g

Frequency Chart

Device ChannelWiFi ChannelFrequency/MHz
AUTO-9AUTOAUTO is the best
10485240
11445220
121495745
131655825

User Tips

No specific user tips are available from the provided data. Always refer to the latest official documentation for best practices.

Warranty and Support

For detailed warranty information and technical support, please refer to the official FEELWORLD website or contact your vendor. A comprehensive user manual in PDF format is also available for download: FEELWORLD WTRS User Manual (PDF).

As product features and performance are continuously improved, specifications may change without prior notice.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.