1. Introduction
Thank you for choosing the LiitoKala Lii-M4 Smart Universal LCD Fast Charger. This advanced intelligent fast charger features button control, 4 independent charging channels, battery capacity detection, reverse polarity protection, short-circuit protection, overcharge protection, USB 5V1A output, and zero-volt battery activation. It continuously monitors the battery charging, discharging, and testing processes.
The Lii-M4 is compatible with various cylindrical Li-ion and NiMH batteries, making it suitable for strong flashlights, electric tools, instruments, digital cameras, and other electronic devices. Its aesthetic design, simple operation, portability, and powerful functions make it an ideal companion for home and travel use.
Figure 1: LiitoKala Lii-M4 Smart Universal LCD Fast Charger and its packaging.
2. Safety Warnings
- This charger is designed exclusively for cylindrical Li-ion and NiMH batteries. Do NOT charge LiFePO4 batteries.
- Before use, please read this manual carefully. Adhere to recommended charging currents and avoid exceeding them.
- Use an appropriate power adapter (DC 5V/2A).
- The charger may generate heat during charging/discharging. Exercise caution to avoid burns.
- When not in use, disconnect the power supply and remove batteries.
- For indoor use only.
- The data displayed by this product is for reference only. For precise measurements, consult professional instruments.
- ⚠️️ Please mind potential fire risk and strictly follow the instruction manual for charging and storage.
3. Functional Features
- Type-C 5V/2A input.
- Two selectable charging currents: 500mA and 1000mA.
- Battery capacity detection function.
- Simultaneous charging for various battery sizes (e.g., 18650, 26650, AA, AAA).
- Clear LCD display showing working mode (CHARGE/TEST), battery voltage (V), charging current (mA), charging time (h), battery capacity (mAh), and percentage (%).
- Independent operation for all 4 channels in CHARGE mode, allowing different charging currents.
- TEST mode involves three steps for capacity detection: 1) full charge, 2) discharge, 3) full charge.
- CHARGE and TEST modes can operate simultaneously. Independent capacity detection and normal capacity detection functions are available, without separate discharge detection.
- Multiple protection features: overcharge, over-discharge, short circuit, 0V voltage activation, (-△V&0△V), 1.65V-2.2V non-chargeable battery detection, intelligent bad battery identification, and reverse polarity detection.
- Standard 5V/1000mA USB output function.
4. Setup Instructions
4.1 Connecting Power
Connect the charger to a power source using the provided Type-C USB cable and a compatible 5V/2A power adapter. The LCD screen will briefly illuminate completely for 3 seconds, indicating it's ready for operation. If no battery is inserted, the display will show "Null".
Figure 2: Charging port (IN: 5V/2A) and USB output port (OUT: 5V).
4.2 Inserting Batteries
Carefully insert the rechargeable batteries into the charging slots, observing the correct polarity (+/-). If a bad or reversed battery is inserted, the display will show "Err".
Figure 3: Compatible battery types and their insertion into the charger.
5. Operating Instructions
5.1 Key Description
The charger has four key points: MODE (mode selection), 1-2 (channel 1-2 query), 3-4 (channel 3-4 query), and CURRENT (current selection). These four keys also illuminate the LCD backlight for easy operation.
Figure 4: Key functions for MODE and CURRENT buttons.
- MODE Button: Used for mode selection, including CHARGE (charging mode) and TEST (capacity detection mode). Normally, long-press the MODE button to switch between CHARGE and TEST modes. First, short-press 1-2 or 3-4 buttons to select the desired channel, then long-press MODE to change the mode.
- 1-2 Channel Button: Corresponds to channels 1 and 2. Short-press repeatedly to cycle through and view data for channels 1 and 2.
- 3-4 Channel Button: Corresponds to channels 3 and 4. Short-press repeatedly to cycle through and view data for channels 3 and 4.
- CURRENT Button: Used to select the charging current. For Li-ion batteries: 500mA/1000mA. For Ni-MH/Ni-Cd batteries: 500mA. Long-press this button to keep the LCD screen constantly lit.
The charger allows independent charging or different current selections, and mixed charging of different battery types. In working status, short-press the 1-2 or 3-4 buttons to view the corresponding channel's current (mA), capacity (mAh), voltage (V), and time (h) data.
5.2 Mode Operation Description
5.2.1 CHARGE Mode
- When the charger is powered on and a battery is inserted, the system automatically enters CHARGE mode. The charger defaults to a charging current of 500mA.
- Within 8 seconds, you can use the CURRENT button to select between 500mA or 1000mA charging current. If no action is taken for 8 seconds, the system will lock the selected current, and the current and other functions will be locked. If you need to change it, long-press the MODE button to re-select.
- While in CHARGE mode and the "CHARGE" indicator is flashing, you can short-press the 1-2 or 3-4 buttons to select a battery channel, then press the CURRENT button to select the current size. After selection, if no action is taken for 8 seconds, it will enter working status. It is important to choose the charging current based on battery capacity. If fast charging is not required, 500mA is recommended for safety.
- In CHARGE mode, short-pressing the 1-2 or 3-4 buttons allows you to view the charging capacity (mAh), charging time (h), charging current (mA), and battery voltage (V) for each channel. Once the battery is fully charged, "End" will be displayed (charging complete).
Note: When charging with 1000mA, only two channels can be charged simultaneously, and only for Li-ion batteries. If more than two channels are used, the system will automatically reduce the 1000mA charging current to 500mA.
5.2.2 TEST Mode (Capacity Detection Mode)
TEST mode first fully charges the battery, then discharges it while recording the discharge capacity and other parameters. Afterwards, it automatically recharges the battery without recording the charging capacity. The display will retain the discharge phase capacity and other parameters. The detailed steps are as follows:
Enter TEST → Select Current & Charge → Battery Charge → Battery Discharge → Re-charge → END
- You can re-enter TEST mode from any state by long-pressing the MODE button.
- After entering TEST mode, within 8 seconds, you can use the CURRENT button to select 500mA or 1000mA current. If no setting is made within 8 seconds, the system will automatically lock to 500mA charging current (this is the system's default charging current).
- Once the battery is fully charged for the first time, the system automatically switches to discharge. The discharge current is fixed at 500mA. At this point, the system records the discharge data to detect the battery's discharge capacity.
- After the battery discharge is complete, the system automatically recharges the battery. The charger will use the previously selected current parameters to recharge the battery. At this time, the system will not record the charging capacity data; it will still display the discharge phase capacity. The "End" indicator will flash until fully charged, then display "End" and "100%", and stop charging.
Note: When charging with 1000mA, only two channels can be charged simultaneously, and only for Li-ion batteries. If more than two channels are used, the system will automatically reduce the 1000mA charging current to 500mA. The discharge current is fixed at 500mA.
5.3 USB 5V Output Function
- The USB port provides a 5V mobile output with a current of 1000mA.
- For the USB output to function, a sufficiently powered Li-ion battery must be inserted into channel 4. This allows the charger to supply power to 5V electronic devices.
6. Maintenance
- Keep the charger clean and dry. Avoid exposure to moisture or extreme temperatures.
- Do not disassemble or modify the charger. Unauthorized modifications can lead to malfunction or safety hazards.
- Always disconnect the power supply and remove batteries when cleaning the charger. Use a soft, dry cloth for cleaning.
- Store the charger in a cool, dry place away from direct sunlight and out of reach of children.
- Ensure adequate ventilation during charging to prevent overheating.
7. Troubleshooting
| Problem | Display | Possible Cause | Solution |
|---|---|---|---|
| Charger powered on, but no battery inserted. | "Null" | No battery detected in the slot. | Insert a compatible battery into an empty slot. |
| Battery inserted, but "Err" displayed. | "Err" | Bad battery, short circuit, or reverse polarity. | Check battery polarity. Remove and re-insert the battery. If "Err" persists, the battery may be faulty. |
| Charger not responding after connecting power. | Blank screen | No power, faulty cable, or adapter. | Ensure power adapter is correctly connected and functional. Try a different USB cable or power adapter. |
| USB 5V output not working. | No output | No Li-ion battery in channel 4, or battery insufficient. | Ensure a charged Li-ion battery is in channel 4. |
8. Specifications
| Feature | Detail |
|---|---|
| Input Voltage/Current | DC 5V/2.0A (Type-C) |
| Li-ion Charging Current | 4.20V, 500mA*4 / 1000mA*2 |
| Ni-MH/Ni-Cd Charging Current | 1.48V, 500mA*4 |
| Compatible Li-ion Battery Types | 3.6V/3.7V/3.8V Li-ion: 10440, 14500, 14650, 16340, 17335, 17500, 17670, 18350, 18490, 18500, 18650, 18700, 20700, 21700, 22650, 25500, 26650, 32650 |
| Compatible Ni-MH Battery Types | 1.2V Ni-MH: AA, AAA, C, AAAA, SC, chewing gum battery |
| TEST Discharge Current | 500mA |
| USB Output | 5V/1000mA |
| Termination Method | Intelligent Voltage Monitoring |
| Display Screen | Yes |
| Intelligent Charge | Yes |
| Quick Charge | Yes |
| Output Power | ≤37.5W |
| Dimensions (L*W*H) | 146mm * 100mm * 33mm |
| Weight (with packaging) | 255g |
Figure 5: Product dimensions.
Figure 6: Back of the charger showing input/output details and safety warnings.
9. User Tips
- The LCD display is very helpful for monitoring charging progress, time, and capacity. Pay attention to these indicators for optimal battery management.
- Ensure you use a reliable 5V/2A power adapter for consistent performance.
10. Warranty and Support
For any issues, questions, or support regarding your LiitoKala Lii-M4 charger, please contact the seller or the official LiitoKala customer service. Keep your purchase receipt for warranty claims.