taslauk 5050 5in1

Contents

taslauk 5050 5-in-1 RGBCCT LED Strip Light User Manual

Model: 5050 5in1

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your taslauk 5050 5-in-1 RGBCCT LED Strip Light. This flexible ribbon tape features a 5-in-1 chip combining Red, Green, Blue, Cool White, and Warm White LEDs, offering a wide spectrum of colors and tunable white light. It is designed for various indoor and outdoor lighting applications, depending on the chosen IP rating.

Rolled taslauk 5050 5-in-1 RGBCCT LED Strip Light
Figure 1: Rolled taslauk 5050 5-in-1 RGBCCT LED Strip Light, showing connections and markings.

2. Safety Warnings

  • Voltage Compatibility: Low-voltage light strips (12V/24V) are strictly prohibited from being directly plugged into a 220V socket. Ensure your power supply matches the strip's voltage.
  • Cutting Precautions: Cutting is only permitted at designated marks. Cutting off-center can cause the entire meter to become non-functional.
  • Live Working Prohibited: Power must be disconnected during cutting and wiring. Live working is strictly prohibited to prevent electrical hazards.
  • Electrostatic Discharge (ESD) Protection: 5050 LED beads are electrostatic sensitive components. Non-professional repair personnel are advised not to touch the chip solder pads with bare hands.
  • Heat Management: Do not stack or coil the light strip for power-on testing, as heat accumulation can quickly burn out the LED beads.

3. Package Contents

Your package should contain the following item:

  • 1 x 5050 5-in-1 RGBCCT LED Light Strip (5 meters)

4. Specifications

Feature Description
LED Type SMD 5050 5-in-1 (RGBCCT)
LED Chip Model 5050
LED Chip Brand SANAN
Working Voltage DC12V / DC24V
Color Output RGBCCT (Red, Green, Blue, Cool White, Warm White)
Luminous Flux 2000-82000 (Lumens, typical range)
View Angle 120°
Working Temperature -20°C to 50°C
Average Life >50,000 hours
Strip Dimensions 500cm (Length) x 1.2cm (Width) x 0.2cm (Thickness)
Strip Type Flat 5-wire
Power Generation Always On
Smart Device Yes
Certification CE, ROHS, UL

LED Density and Power Consumption:

  • 60 LEDs/meter: 24W/meter
  • 84 LEDs/meter: 28-30W/meter
  • 96 LEDs/meter: 36W/meter
  • 112 LEDs/meter: 40W/meter
Different LED densities for taslauk LED strip
Figure 2: Visual representation of different LED densities (60, 84, 96, 112 LEDs per meter).

Waterproofing Options:

  • IP20: Not waterproof, suitable for indoor dry environments.
  • IP65: Waterproof, suitable for areas with splashes or moisture.
  • IP67: Tube waterproof, offering enhanced protection against water ingress.
Waterproofing types for taslauk LED strip: IP20, IP65, IP67
Figure 3: Comparison of IP20 (Not waterproof), IP65 (Waterproof), and IP67 (Tube waterproof) versions.

5. Setup and Installation

5.1 Unpacking and Initial Check

  1. Upon receiving, carefully unpack the LED strip.
  2. Verify the voltage (12V or 24V) and type of the light strip. Ensure it matches your power supply.
  3. Perform a quick functional test before permanent installation. Do not stack or coil the light strip during this test to prevent heat buildup.

5.2 Surface Preparation

  • The installation surface must be thoroughly cleaned, free of dust, oil, and moisture. A clean surface ensures optimal adhesion of the double-sided tape.
  • Repositioning the strip significantly reduces its adhesive strength. Plan your placement carefully and position it correctly the first time.

5.3 Cutting the LED Strip

  • The LED strip can be cut to desired lengths only at the designated cutting marks (indicated by a scissor icon).
  • Ensure power is disconnected before cutting. Live working is strictly prohibited.
  • Verify the scissor mark is not offset before cutting. Cutting off-center can render the entire meter segment non-functional.

5.4 Adhesion and Securing

  • Peel off the backing from the double-sided tape and firmly press the strip onto the prepared surface.
  • Note that the 3M adhesive may lose effectiveness after prolonged exposure to sunlight and rain. For outdoor or high-moisture applications (IP65/IP67), it is recommended to secure the strip further using matching clips, slots, or ties.
  • For IP67 (tube waterproof) versions, apply waterproof glass cement at any joints or cut ends to maintain water resistance.

5.5 Wiring

  • Connect the 5-wire output of the LED strip to a compatible RGBCCT controller and power supply. Ensure correct polarity (+V, R, G, B, WW, CW).
  • Always ensure the power supply is disconnected before making any wiring connections.
taslauk LED strip showing multi-wire connection
Figure 4: Detail of the multi-wire connection for the RGBCCT LED strip.

6. Operating Instructions

The taslauk 5050 5-in-1 RGBCCT LED Strip Light is designed to be controlled by an external RGBCCT controller (not included). Once properly installed and connected to a compatible controller and power supply, you can operate the strip as follows:

  • Power On/Off: Use the controller to turn the LED strip on or off.
  • Color Selection: Utilize the controller's interface (buttons, remote, or app) to select desired RGB colors.
  • White Light Adjustment: Adjust the brightness and color temperature of the white light using the dedicated Cool White (CW) and Warm White (WW) controls on your controller.
  • Brightness Control: Most controllers offer dimming capabilities to adjust the overall brightness of the strip.
  • Dynamic Modes: Explore various pre-programmed dynamic modes (e.g., flashing, fading, color cycling) available on your controller.
taslauk LED strip displaying various colors
Figure 5: The LED strip showcasing its ability to produce various colors including red, green, blue, and different shades of white.

7. Maintenance

  • Cleaning: Gently wipe the LED strip with a soft, dry cloth to remove dust. For IP65/IP67 versions, a damp cloth can be used, but ensure no water enters connections.
  • Inspection: Periodically check the strip for any signs of damage, loose connections, or adhesive degradation.
  • Heat Dissipation: For optimal performance and extended lifespan, consider installing the LED strip in aluminum channels. These channels not only enhance heat dissipation but also improve light emission uniformity.

8. Troubleshooting

Problem Possible Cause Solution
LED strip does not light up No power, incorrect wiring, faulty power supply/controller. Check power connections, ensure correct voltage and polarity. Test power supply and controller.
Part of the strip is not lighting up Incorrect cutting, damaged segment, loose connection. Ensure cuts were made precisely at designated marks. Check for physical damage or loose connections in the affected segment.
White or Warm White colors not working correctly Faulty connection to CW/WW channels, controller issue, damaged LED chip. Verify connections for the Cool White and Warm White channels. Test with a different controller if possible. If a segment is damaged, it may require replacement.
Adhesive not holding Improper surface preparation, prolonged exposure to elements, repositioning. Ensure surface is clean and dry. Use additional clips, channels, or ties for secure mounting, especially in challenging environments.
LEDs burning out quickly Overheating due to stacking/coiling during operation/testing, incorrect voltage. Ensure proper heat dissipation. Never operate the strip while coiled. Verify correct voltage supply.

9. User Tips

  • Test Before Final Installation: Always test the full functionality of your LED strip, including all colors and white light channels, before permanently installing it. This can save significant effort if an issue is present.
  • Consider Aluminum Channels: For a professional finish and improved longevity, especially in areas where heat might be a concern, consider mounting your LED strip in aluminum profiles.
  • Clean Surface is Key: The effectiveness of the adhesive relies heavily on a clean, dry, and smooth installation surface. Take extra time to prepare it properly.

10. Warranty and Support

The taslauk 5050 5-in-1 RGBCCT LED Strip Light is designed for a long lifespan of over 50,000 hours under normal operating conditions.

For further assistance or detailed technical information, please refer to the official user manual PDF:

View User Manual (PDF)

© 2023 taslauk. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.