1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your new LEEOCAR Android Car Radio. Please read this manual thoroughly before installation and use to ensure proper functionality and to avoid damage.
Figure 1: LEEOCAR Android Car Radio Unit
2. Vehicle Compatibility
This Android Car Radio is designed for the following BMW 3 Series models:
- BMW 3 Series 328i, 335i, 325i (E90/E91/E92/E93) 2005 - 2011
- BMW E90 Sedan (2005-2012)
- BMW E91 Touring (2005-2012)
- BMW E92 Coupe (2006-2013)
- BMW E93 Convertible (2007-2013)
- BMW (E90 / E92 / E93) M3 (2007-2012)
Important Compatibility Notes:
- If your car has a premium sound system (J.B.L or B.O.S.E) or a factory navigation system, this radio is NOT supported.
- If your original car radio plug has 8 speaker wires, direct installation is possible. If it does NOT have 8 wires, this radio is NOT supported.
- The original A/C control panel must be moved to the original storage box location. The package includes two bezels for this conversion.
- If your car has an iDrive system and LCD display, it is not compatible.
- If you wish to retain the original buttons, an ashtray button relocation kit (NOT included) is required.
Figure 2: Visual Guide for Car Version and Wiring Compatibility
3. What's Included in the Package
Please verify all items are present upon unboxing. If any accessories are missing, contact customer service.
Figure 3: Included Components and Accessories
The package typically includes:
- Main Head Unit (9-inch display)
- Power Cable
- RCA Cables
- USB Cables (x2)
- GPS Antenna
- Backup Camera Video Input Cable
- Microphone
- CAN Bus (if applicable)
- Radio Antenna Adapter Cable
- 15A Fuse
- Manual Air Conditioning Bracket
- Automatic Air Conditioning Bracket
- Mounting Brackets (x2)
- Screw Caps (x2)
- Clips (x2)
- Screws (x12)
- User Manual (PDF reference: User manual (PDF))
4. Setup and Installation
WARNING: Do not connect wiring while power is on. Doing so may result in system errors, fuse damage, or permanent malfunction. Always disconnect the car battery before installation.
4.1. Removing the Original Vehicle's Radio
A detailed step-by-step installation video is available. Please contact customer support for access to this video.
4.2. A/C Bracket and Control Panel Trim Installation
For the A/C bracket, use a precision cutting tool (e.g., rotary tool or small hobby saw) to carefully cut off the red-marked tabs on your factory A/C control module. Be careful not to cut the middle part between the two red areas, as this center section is essential for proper installation. After trimming, your control module should resemble the example image with the outer tabs removed and the central portion intact. Once trimmed, install the A/C bracket, ensuring it is oriented correctly.
For the A/C Control Panel Trim, choose the correct trim based on your vehicle's A/C type: use the manual A/C trim for manual A/C, and the automatic A/C trim for automatic A/C.
4.3. Radio Wiring Diagram
Refer to the diagram below for proper wiring connections. Only connect the labeled plugs on the original car radio. The remaining plugs do not need to be connected.
Figure 4: Radio Rear Panel Pinout and Wiring Diagram
Wiring Harness Connection Tutorial:
- Power Cord: Connect to the vehicle's power supply.
- USB: Connect USB devices.
- Reverse Input: For backup camera.
- GPS: Connect GPS antenna.
- Radio Cable: Connect radio antenna.
- RCA Cables: CVBS-IN-1, MIC, SUB WOOFER, AUX IN R, AUX IN L, AUDIO OUT L, AUDIO OUT R, AMP CONT.
4.4. Rear Camera Wiring
Connect the camera's red wire to the positive terminal of the backup light and the black wire to the negative terminal. Connect the video cable from the camera to the 'Reverse Input' on the head unit. The camera input cable also has two small antennas to enhance Bluetooth and WiFi signals.
Figure 5: Rear Camera Wiring Diagram
For a visual guide, please scan the QR code provided in the original manual to watch the tutorial video.
4.5. CANBUS Box Setup (if applicable)
If your vehicle requires a CANBUS Box to retain original car information display, follow these steps:
- Go to Settings > Factory Settings > Protocol settings.
- Select the correct Protocol Box Brand (check the surface of the protocol box for the brand).
Generally, completing the protocol box matching will automatically activate the steering wheel control function.
5. Operating Instructions
5.1. Wireless Apple CarPlay & Android Auto
Connect your iPhone wirelessly via Bluetooth to enable Apple CarPlay, allowing access to Siri voice control, music, map navigation, calls, and messages. For Android phones, connect via Bluetooth for Wireless Android Auto to access navigation, calls, messages, and music, and utilize the Voice Assistant.
Figure 6: Wireless Apple CarPlay and Android Auto Interface
5.2. Wired/Wireless Mirror Link (Android/iOS)
Mirror your phone screen to the head unit. For iOS, wireless connection via hotspot is supported (one-way projection). For Android, both wireless (hotspot) and wired (USB) connections are supported (two-way connection). This allows access to your phone's navigation, music, and other apps on the car stereo screen.
5.3. WiFi Connection
Connect the head unit to a mobile phone hotspot or a WiFi device to access online features. This enables downloading apps (Youtube, Spotify, Pandora), online video streaming, online map navigation, and general internet browsing.
Figure 7: WiFi and Hotspot Connectivity for Online Features
5.4. GPS Navigation
The stereo comes with a GPS antenna and pre-installed offline map files, allowing navigation without an internet connection. When connected to WiFi, you can also use online GPS navigation apps. The unit is compatible with most navigation apps from the Play Store (e.g., Sygic, Waze, Navitel IGO).
5.5. FM Radio Receivers
Enjoy high-quality FM radio with RDS, supporting 18 preset stations for music, traffic info, and weather forecasts. The unit supports automatic or manual station searching. FM Range: 87.5~108MHz.
5.6. Bluetooth Handsfree Calls and Music
The built-in Bluetooth 5.1 module supports hands-free calls for safe driving and wireless music streaming. It also supports automatic phonebook loading and contact searching, synchronizing your mobile phone book to the device.
5.7. Touch Screen and Split Screen Functionality
The 9-inch 2.5D touch screen provides a clear visual experience. The split-screen function allows you to view two applications simultaneously, such as GPS navigation and music playback.
5.8. DSP & EQ Settings
The unit supports various music styles (Hifi, Bass, Rock, Pop) and allows you to customize your preferred audio settings for an enhanced listening experience.
Figure 8: Audio Playback and DSP Features
5.9. Steering Wheel Control
The unit supports existing steering wheel buttons for controlling various functions. To set up, go to Settings > Protocol Settings > Car Model and select "OD--BMW--E90--OD".
Figure 9: Steering Wheel Control Interface
6. Maintenance
- Cleaning: Use a soft, dry cloth to clean the screen and unit. Avoid abrasive cleaners or solvents.
- Software Updates: Periodically check for system updates to ensure optimal performance and access to new features.
- Environmental Conditions: Avoid exposing the unit to extreme temperatures, direct sunlight for prolonged periods, or excessive moisture.
7. Troubleshooting (FAQ)
7.1. General Issues
- Q: What is the factory password?
- A: The factory password is 3368.
- Q: What should I do if the radio experiences issues like freezing and stuttering?
- A: Go to Settings > User > Backup and Reset (enter "3368") > Erase All Data (Factory Reset). Alternatively, perform a hard reset by using a pin-like tool to press the RST hole on the front panel of the radio for 5-10 seconds.
- Q: Why is the time not accurate?
- A: Ensure your GPS antenna is properly connected, ideally on the A-pillar or outside the dash. Then, connect your radio to Wi-Fi or a hotspot, go to Settings > System > Date and Time, and enable "Use network-provided time" and "Use network-provided time zone."
7.2. Audio and Radio Issues
- Q: Why can't I receive FM radio stations after installing the new head unit?
- A: If your vehicle is a high-trim model, ensure the high-trim radio antenna adapter is properly connected to the original factory radio antenna socket. Connect the blue wire from the high-trim antenna adapter to the red ACC (Accessory Power) wire on the 16-pin power harness to provide necessary power to the antenna amplifier. Failure to do so may result in poor or no FM signal reception.
- Q: Why is there no sound from the radio after installation?
- A: Check if your factory connector includes an amplifier control wire or a MOST (Media Oriented Systems Transport) wire. If it has an amplifier control wire, open the Radio app, go to Settings, and enable "RDS." If it has a MOST wire (usually two orange wires), you will need to purchase an additional fiber optic box for the audio to function properly.
-
Figure 10: Amplifier Control Wire and MOST Wire Diagram
- Q: No sound may be because your car has a power amplifier.
- A: You must find the power cable of the amplifier and connect it with the 12V ACC cable of our product.
- Q: Does it support the original car microphone?
- A: No, the factory microphone cannot be retained. Connect the external microphone to the 3.5mm port on the RCA cable. Install the microphone on the driver's side sun visor, with the microphone head facing the driver's face.
7.3. Camera Issues
- Q: The rear camera image is reversed (left to right). How can I fix it?
- A: Go to Settings > General and toggle the "Mirror view on reverse image" option to adjust.
- Q: Why is the original car's rear camera image not clear?
- A: Factory rear camera images may not be clear due to older CVBS (360P) signals. Our new radio supports AHD (1080P). We recommend using the supplied camera for better image quality.
- Q: How do I turn off the camera's guideline?
- A: Go to Settings > Factory (enter "3368") > Original Car Agreement and turn off "Reverse Parking Line."
- Q: If the reverse camera image appears abnormal after correct connection, please manually adjust the resolution of the camera.
- A: Steps: Settings > Factory settings > Rear on-board signal source settings. Then turn off the stereo and restart it after five minutes. If some vehicles still don't display the reverse camera properly after starting, it might be due to insufficient voltage; consider adding a reversing rectifier to stabilize the voltage.
- Q: Does it support the factory backup camera?
- A: No, it does NOT support the factory backup camera. Please use the camera provided with the unit.
7.4. Other Issues
- Q: Is it possible to support Sirius XM radio?
- A: The radio does not have a port for connecting a SiriusXM tuner. You may check the Play Store for an online SiriusXM Radio app, but compatibility with third-party apps cannot be guaranteed.
- Q: Can I use a voice assistant (Siri, etc.)?
- A: The voice assistant can only be activated through your phone. Connect your phone to the radio via Bluetooth, Android Auto, or CarPlay to use the voice assistant feature.
- Q: How to control the seat heating function?
- A: Go to Vehicle settings, then turn on "Left seat heating" and "Right seat heating." Note that the Center Console Switch Panel (with function buttons) is not required for installation and should be left out.
8. Specifications
| Feature | Specification |
|---|---|
| Operating System | Android 12 |
| CPU | 4-Core |
| RAM | 4G |
| ROM | 64G |
| Display Size | 9 inches |
| Touch Screen | Yes, 2.5D |
| Built-in Screen | Yes |
| Wireless CarPlay & Android Auto | Supported |
| Mirrorlink | Wireless/Wired (iOS wireless, Android wireless/wired) |
| Voice Control | Supported (via connected phone) |
| Bluetooth Version | 5.1 |
| FM Radio Range | 87.5~108MHz |
| GPS Navigation | Built-in (offline maps, supports online maps) |
| Steering Wheel Control | Supported |
| Backup Camera | Free backup camera included, HD night vision, 170° wide angle, IP68 waterproof |
| Special Features | WiFi function, Built-in GPS, Split Screen, MP3 players, CarPlay, Voice Control, Android Auto, DSP, Reversing Input, Support steering wheel control, Support Can-Bus |
| Digital Media Format | MP4, Mp3, WMA, JPEG |
| Out Power | 4*45W |
| Voltage | 12 V |
| Item Weight | 2.5kg |
| Material | Composite Material |
| Certification | CE, FCC, WEEE, EAC, RoHS, KC |
| OSD Language | Multi-language support (Simplified Chinese, Traditional Chinese, Albanian, Arabic, Azeri, Irish, Estonian, Belarusian, Bulgarian, Icelandic, Polish, Persian, Boolean text (Dutch South Africa), Danish, German, Russian, French, Filipino, Finnish, Georgian, Haitian Creole, Korean, Dutch, Galicia, Catalan, Czech, Croatian, Latin, Latvian, Lithuanian, Romanian, Maltese, Malay, Macedonian, Norwegian, Portuguese, Japanese, Swedish, Serbian, Slovak, Slovenian, Swahili, Thai, Turkish, Welsh, Ukrainian, Hebrew, Greek, Spain's Basque, Spanish, Hungarian, Armenian, Italian, Yiddish, Hindi, Urdu India, Indonesian, English, Vietnamese) |
9. User Tips
- GPS Antenna Placement: For optimal GPS signal, install the GPS antenna on the A-pillar of your car or just outside the dash. It will not function correctly if installed inside the dash.
- A/C Bracket Modification: When installing the A/C bracket, carefully cut only the specified tabs and preserve the central portion of your factory A/C control module for proper fitment.
- Bluetooth/WiFi Signal: Ensure the camera input cable is properly connected, as it contains small antennas designed to enhance the radio's Bluetooth and WiFi signals.
- Voltage Check: Always verify the car radio's voltage is 12V. Over 12V may damage the radio.
- Power Cable Usage: Always use the provided power cables to connect the car radio. Do not attempt to insert the original car plug directly into the new unit.
10. Warranty and Technical Support
The product comes with a 1-year warranty.
For any questions regarding installation, wiring, or other technical assistance, please contact our customer service team. We provide lifetime technical support.
You can also access additional support resources:
- User Manual (PDF): A detailed user manual is available in PDF format. Reference: User manual (PDF)
- Online Support: Scan the QR code below to visit our official website for after-sales support, FAQs, and community forums.
Figure 11: QR Code for Technical Support Website
The barcode shown in some documentation is for warehouse use only and is not relevant for installation or support.