JIKONG JK-B2A8S20P

Contents

JIKONG JK-B2A8S20P Smart BMS User Manual

Model: JK-B2A8S20P

1. Product Overview

The JIKONG JK-B2A8S20P is an intelligent Battery Management System (BMS) designed for large-capacity series lithium battery packs. It provides comprehensive management and protection features to ensure the safety and longevity of your battery system.

1.1. Key Features

  • Voltage Acquisition: Monitors individual cell voltages with high precision.
  • High Current Active Balancing: Achieves up to 2A balance current to maintain cell consistency, extend battery range, and delay aging.
  • Comprehensive Protection: Includes overcharge, over-discharge, overcurrent, over-temperature, under-temperature, and short-circuit protection.
  • Coulomb Meter: Accurate State of Charge (SoC) tracking.
  • Communication: Integrated Bluetooth for mobile APP connectivity (Android and iOS), optional RS485 and CAN communication.
  • GPS Remote Function: Optional GPS support for battery location tracking.
  • Heating Function: Optional low-temperature heating to maintain battery performance in cold environments.
  • Parallel Function: Optional support for battery pack parallel operation.
  • ACC Detection: Optional function for discharge control and charger detection.
  • Intelligent Sleep Mode: Reduces self-consumption during standby.
  • Emergency Switch: Provides a temporary override for critical situations.

The BMS is compatible with various lithium battery chemistries, including Lithium Iron Phosphate (LiFePO4), Ternary Lithium (Li-ion), and Lithium Titanate (LTO) batteries, supporting configurations from 4S to 8S.

JIKONG JK-B2A8S20P Smart BMS front view

Figure 1: JIKONG JK-B2A8S20P Smart BMS

2. Setup and Installation

2.1. Package Contents

The standard package typically includes:

  • JIKONG JK-B2A8S20P Smart BMS unit
  • Balance wires (cell voltage sensing wires)
  • Temperature sensors (NTC)
  • Communication cables (e.g., for display, RS485, UART)
  • Mounting screws/hardware

2.2. Physical Installation

Ensure the BMS unit is securely mounted to your battery pack or enclosure. The casing is made of aluminum alloy for ruggedness and efficient heat dissipation. Avoid mounting in areas with excessive vibration or direct exposure to moisture.

Aluminum alloy shell of JIKONG BMS

Figure 2: Rugged Aluminum Alloy Shell

2.3. Wiring Diagrams

Important: Before connecting, ensure all balance wires are correctly connected to their respective cells and that the main P- and B- terminals are correctly identified. Incorrect wiring can cause severe damage to the BMS and battery.

2.3.1. Internal Architecture Sample

This diagram illustrates the internal components and their interconnections within the BMS. It shows the MCU as the central processing unit, managing various modules like MOS drivers, current sensing, balancing, DAQ, temperature sensing, and communication interfaces.

JIKONG BMS Internal Architecture Diagram

Figure 3: BMS Internal Architecture. Key components include MCU, MOS Driver, Current Sensing, EEPROM, LED Indicator, Buzzer, Bluetooth, Balancing Module, DAQ Module, Temp Sensing (T1-T4), Power Module, Switching Module, RS485, LCD, GPS, CAN, Heating, Parallel interfaces. B+ and B- are main battery terminals, P-/C- is the common port for load/charger.

2.3.2. 8S Connection Sample

This diagram shows a typical wiring setup for an 8-series battery pack. Connect the main B- terminal to the battery pack's negative terminal. Connect the main P- terminal to the common negative terminal for both the controller (load) and charger. The B+ terminal connects to the battery pack's positive terminal. Individual cell voltage taps (1+ to 8+) must be connected sequentially from the first cell's positive to the last cell's positive.

JIKONG BMS 8S Wiring Diagram

Figure 4: 8S Battery Pack Wiring Diagram. Shows connections for Controller, Charger, main B+ and B- terminals, and individual cell balance wires (1+ through 8+).

2.3.3. General Installation Method (3-8 Series)

The JK-BxA8S-20P series protection board is suitable for 3-8 series lithium battery packs. The specific wiring method depends on the number of cells in your battery pack. Always follow the provided wiring diagrams carefully.

JIKONG BMS General Wiring Diagram

Figure 5: General Wiring Diagram. Illustrates connections for Load, Charger, Protection Board Heating Wire, Heater Element, Temperature Control Switch, Temperature Probe, and main B+ and B- terminals with cell taps.

2.4. APP Installation

The JIKONG Smart APP allows for convenient monitoring and control of your BMS. It is available for both Android and iOS devices. Android Version 7 or higher is required.

  1. Scan the QR code below using your smartphone's camera or a QR code scanner app.
  2. Follow the on-screen instructions to download and install the APP.
JIKONG Smart APP QR Code

Figure 6: JIKONG Smart APP QR Code

2.5. Device Activation

Before powering on the BMS:

  1. Double-check that all balance wires are correctly connected and secure.
  2. Verify that the main P- and B- terminals are correctly wired.
  3. Ensure the BMS is securely fixed to the battery pack.

The BMS does not have a physical power-on switch. It activates in one of three ways:

  • Charger Activation: Connect a charger with an output voltage at least 2V higher than the current battery pack voltage.
  • Key Activation: If equipped with an external button, press it to activate.
  • Display Activation: If equipped with a display unit, connecting it may activate the BMS.

3. Operating Instructions

3.1. Basic Operation and Monitoring

Once activated, the BMS will begin monitoring your battery pack. You can view real-time data and adjust settings using the JIKONG Smart APP.

JIKONG Smart APP Interface

Figure 7: JIKONG Smart APP Interface (About, Control, Device List)

3.2. APP Usage and Parameter Settings

The APP provides access to various settings and real-time data:

  • About: Displays BMS firmware version, serial number, power-on times, etc.
  • Control: Allows you to enable/disable functions like heating, balancing, and set various protection parameters.
  • Device List: Shows connected BMS units.

Before using certain functions, such as active balancing, you must set basic battery parameters in the APP, including:

  • Battery type (LiFePO4, Li-ion, LTO)
  • Number of cells in series
  • Battery capacity (Ah)
  • Trigger equalization voltage difference (mV)
  • Voltage and current calibration (if needed)

3.3. Specific Functions

3.3.1. Active Equalization

The BMS uses energy transfer active balancing. Energy from higher voltage cells is transferred to lower voltage cells. You can set the trigger voltage difference in the APP. The default balance current is 1A or 2A, adjustable based on battery capacity. Balancing can be enabled/disabled via the APP.

3.3.2. Heating Function (Optional)

For low-temperature operation, the optional heating function uses a resistance heater or film to warm the battery. It operates at 20A. Control this function via the APP. It is recommended to install an external temperature control switch (45°C to 65°C normally closed) in series for secondary protection.

3.3.3. Alarm Function (Optional)

If enabled, the BMS will trigger an external alarm when safety risks like over-temperature, overcharge, or over-discharge are detected.

3.3.4. Battery Parallel Function (Optional)

For parallel battery packs, this function requires a dedicated parallel module. Ensure


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.