1. Introduction
This manual provides essential instructions for the safe and efficient operation, assembly, maintenance, and troubleshooting of the Heimerdinger LB340 Brushless Rebar Tying Machine. Please read this manual carefully before use and keep it for future reference.
For additional information, you may refer to the User Manual (PDF).
2. Safety Warnings
⚠ WARNING: To avoid accidents, always disconnect the Battery Pack from the tool before cleaning or performing any maintenance.
⚠ WARNING: Do not point the tool towards yourself or anyone nearby. Unexpected triggering will discharge the fastener causing an injury.
⚠ CAUTION: Before inserting the battery pack, ensure your fingers are kept away from the switch trigger and the trigger is locked. If the battery pack is inserted while the switch trigger is pulled, the tying operation may be activated accidentally, which could result in an accident.
⚠ CAUTION: When turning on the power, never allow your limbs or face to come near the tying or rotating parts of the tool head. Otherwise, you may be injured.
General Power Tool Safety
- Keep the work area clean and well-lit.
- Do not operate power tools in explosive atmospheres.
- Keep children and bystanders away while operating a power tool.
- The plug of the power tool must match the socket. Never modify the plug in any way.
- Avoid physical contact with grounded surfaces.
- Do not expose the power tool to rain or moisture.
- Do not misuse the power cord. Keep the cord away from heat, oil, sharp edges, and moving parts.
- When using the power tool outdoors, use an extension cord suitable for outdoor use.
- If operation in a damp environment cannot be avoided, use a power source protected by a Residual Current Device (RCD).
- Power tools generate electromagnetic fields (EMF) that are harmless to users. Consult a physician if you have a pacemaker.
- Stay alert, pay attention to the operation being performed and stay awake when operating power tools. Do not operate when tired or under the influence of drugs, alcohol, or medication.
- Use personal protective equipment, including goggles, dust masks, non-slip safety shoes, helmets, and hearing protection.
- Prevent accidental starting. Ensure the switch is in the OFF position before connecting power/battery packs, picking up, or carrying the tool.
- Remove all adjustment keys or wrenches before turning the power tool ON.
- Do not overextend your hands. Maintain proper footing and body balance.
- Dress appropriately. Do not wear loose clothing or jewelry. Keep hair and clothing away from moving parts.
- If devices are provided for connection to chip removal and dust collection equipment, ensure they are connected properly and used appropriately.
- Do not wear fabric work gloves that may become entangled while using this tool.
Specific Safety Warnings for Rebar Tying Machine
- Never point the tool at yourself or others. Keep hands and feet away from the tool head.
- Do not load binding wire while the tool is powered on.
- Do not operate the tool with the wire reel cover open.
- Before starting work, always check that the diameter of the rebar to be tied is within the tool's tying capacity.
- Wear close-fitting clothing without loose ends or sleeves.
- Before using the tool, ensure all parts are undamaged, all bolts are tight, and all safety devices are functioning properly.
- If any abnormality is detected, stop using the tool immediately and contact your local Heimerdinger service center for repairs.
- When installing the battery pack, always lock the switch trigger and keep your fingers off the trigger.
- When tying rebar, take care not to move them.
- Do not touch the binding wire during the tying process.
- Do not place your hands near the tying point during the tying process.
- Hold the tool handle firmly during tying.
- Do not move to the next tying point before the current tying process is complete.
- Be aware of the wire end during the tying process.
- Do not touch the contact plate during the tying process.
- After completing a tying operation, lift the tool vertically upward.
- Handle the tool carefully to avoid dropping, impacting, or striking it.
- If the tool operates immediately after installing the battery pack, overheats, produces unusual odors, or shows an error, lock the trigger, turn off power, and remove the battery pack.
- When working on scaffolding or high platforms, maintain a well-balanced posture and ensure no one is below.
- Do not use this tool for any purpose other than tying rebar.
- Always use genuine Heimerdinger binding wire. Do not use rusted wire.
- After tying, check for any wire breakage. Adjust tying force and re-tie if necessary.
- Press the clamp arm firmly against the rebar to avoid gaps.
3. Symbols
The following symbols may be used on the equipment. Understand their meaning before use.
- ⚠: Warning/Caution - Indicates potential hazards.
- 👁: Wear safety glasses.
- ☁: Do not expose the tool to rain.
- 👋: Keep hands away from the wire reel or binding wire during operation.
- 👋: Keep both hands away from the tool head.
- 🔍: Before loading binding wire, push the release lever. After installation, release the locking lever.
- ☓: Restricted to EU Countries - This device contains hazardous components.
- 🗑: Do not dispose of electrical and electronic tools or batteries with general household waste.
- Ni-MH / Li-ion: Indicates battery type.
4. Intended Use
The Heimerdinger LB340 Brushless Rebar Tying Machine is designed specifically for tying reinforcement bars in construction projects. It is suitable for various applications including building construction, road & tunnel projects, and bridge engineering.
5. Specifications
| Feature | Specification |
|---|---|
| Model | LB340 |
| Brand Name | Heimerdinger |
| Power Source | Electric (DC18-21V) |
| Motor | Brushless |
| Power | 150W |
| Binding Range | 8-34mm |
| Wire Diameter | 0.8mm |
| Certification | CE |
| Origin | Mainland China |
| Package Length | 50 cm |
| Package Width | 36 cm |
| Package Height | 13 cm |
| Package Weight | 5.2 kg |
6. Assembly
6.1. Installing or Removing Battery Cartridge
⚠ CAUTION: Always switch off the tool before installing or removing the battery cartridge.
⚠ CAUTION: Hold the tool and the battery cartridge firmly when installing or removing. Failure to do so may result in damage or personal injury.
- To remove the battery pack, press the button on the front side of the battery pack while pulling it out of the tool.
- To install the battery pack, align the tongue on the battery pack with the groove on the tool housing, then push in and slide it into place. Insert fully until the battery pack locks into position with an audible click. If the red indicator on the button remains visible after insertion, the battery pack is not fully locked.
⚠ CAUTION: Be sure to fully load the battery pack until the red indicator light is not visible. Otherwise it may accidentally fall out of the tool, resulting in injury to yourself or others.
⚠ CAUTION: Do not force the battery pack. If the battery pack is difficult to insert, it may have been inserted improperly.
6.2. Loading the Binding Wire (Wire Reel)
⚠ WARNING: When installing or removing binding wire or accessories, always turn off the power, lock the trigger, and remove the battery pack. Failure to do so may result in an accident.
Note: Use of non-genuine Heimerdinger binding wire may cause tool malfunction.
- Locate the "Knob" (Figure 6.2). Grasp the knob with your fingers and turn it counterclockwise. Lift the Wire Coil Cover upward to fully expose the wire reel compartment.
- Remove the wire spool and cut the binding strap (ensure the wire is not knotted or bent). Straighten approximately 10 cm of the wire end. Confirm the correct orientation of the wire reel and carefully place it into the reel compartment in a vertically downward direction as indicated by the arrow (Figure 6.3).
- After confirming the reel is correctly oriented, press the latch button to ensure the reel securely engages with the fixing structure inside the compartment. Insert the straightened wire end into the wire guide tube and push the wire forward until it cannot advance further. To verify if the wire is properly installed, you can press the clutch button and continue pushing the wire forward slightly until the gears fully grip the wire.
Note: When cutting the binding strap, firmly hold the wire spool to prevent the wire from unwinding loosely. Loose wire can easily cause reel jamming and malfunction.
7. Operating Instructions
7.1. Main Power Switch
When the power button is pressed, the power turns on and the battery charge indicator light illuminates. Press the power button again to turn off the power, and the battery charge indicator light goes off.
7.2. Switch Operation
⚠ WARNING: Before inserting the battery pack into the tool, always verify that the switch trigger can be pulled smoothly and returns fully to the "OFF" position when released.
⚠ CAUTION: When the tool is not in operation, slide the trigger lock button to the "LOCK" position to secure the switch trigger in the OFF position.
To prevent accidental activation of the switch trigger, this tool is equipped with a trigger lock button. To start the tool, slide the trigger lock button to the "UNLOCK" side, then pull the switch trigger. The tool stops operating when the switch trigger is released. After use, slide the trigger lock button back to the "LOCK" side.
After pulling the switch trigger, the tool performs the following operations in sequence and then stops automatically:
- Feeds the binding wire.
- Cuts the wire.
- The hook secures and twists the wire.
- The hook returns to its original position.
7.3. Tying Force Adjustment
⚠ CAUTION: Before making any adjustments, always lock the trigger. When the power is turned on, never allow your limbs or face to come near the tying or rotating parts of the tool head. Otherwise, you may be injured.
By turning the adjustment knob, you can adjust the tool's tying force to suit different materials and thicknesses for various tying requirements. Before adjustment, always lock the tool's trigger to prevent accidental activation.
Rotate the tying force adjustment knob:
- Toward the "+" direction: Increases the tying force.
- Toward the "-" direction: Decreases the tying force.
7.4. Tying Techniques
- Position the tool at a 45° angle facing the rebar intersection, and tie the wire in alternating directions as shown in the illustration (Figure 7.5).
- Bind the wire onto the flat (non-protruding) cross-section of the intersecting rebars.
- If the tying force is insufficient, perform a second tie from the opposite direction to reinforce the binding strength.
Note: When performing a second tie, always bend the wire tail from the first tie before proceeding with the second tie. Otherwise, the wire may be obstructed during the second tying attempt. This could cause the wire to entangle the tool head and potentially damage the twisting hook.
8. Battery Protection Systems
This tool is equipped with a battery protection system that automatically cuts off power to the motor to prolong battery life.
8.1. Overload Protection
If the tool is operated in a manner that causes abnormally high currents, the system will cut off power. Turn the tool off, stop the application causing the overload, then turn the tool on and restart. If the tool does not start, the battery may be overheating. Wait until the battery cools down before restarting.
8.2. Low Battery Voltage Protection
When the remaining battery power is too low, the tool will stop running. If you start the tool, the motor may run briefly but will stop soon. In this case, remove and recharge the battery.
8.3. Protection From Other Causes
The protection system also prevents other issues that could damage the tool. If the tool temporarily stops or ceases to operate, perform the following steps:
- Turn the tool power off and back on to restart it.
- Charge the battery or replace it with a charged battery.
- Wait for the tool and battery to cool down.
If there is no improvement after restoring the protection system, contact your local Heimerdinger Service Center.
9. Maintenance
- Cleaning: Clean the machine surface regularly to keep the wire beak and other areas clean. Never clean the tool with gasoline, benzene, thinner, alcohol, or similar substances, as this can cause discoloration, deformation, or cracking.
- Handling: Do not throw the machine, as this can damage parts.
- Battery Care: Do not put the battery and other metal objects together to prevent short circuits.
- Repairs: Disassembling the machine by unauthorized personnel is prohibited. For any irresoluble faults or repairs, return the machine to an authorized Heimerdinger maintenance personnel or service center.
- Wire Storage: Wire that is stored unused for extended periods may rust. Do not use rusted wire.
10. Troubleshooting
- Tool not starting or stopping unexpectedly: If the tool operates immediately after installing the battery pack, overheats, produces unusual odors or noises, or displays an error message, lock the trigger, turn off the power, and remove the battery pack. Contact a service center if the issue persists.
- Wire entanglement or jamming: This can occur if the clamp arm is moved during tying, if the wire tail is not bent during a second tie, or if loose wire unwinds from the spool. Ensure proper wire loading and tying techniques. If the tool head or twisting hook is damaged, contact a service center.
- Battery pack difficult to insert or not locking: Ensure the battery pack is aligned correctly with the tool housing grooves. Push firmly until an audible click is heard and the red indicator light is no longer visible. Do not force the battery pack.
- Insufficient tying force or wire breakage: This may be due to excessive twisting tension. Adjust the tying force using the knob (refer to section 7.3) and re-tie the rebar.
- Loose ties or gaps: Ensure the clamp arm is pressed firmly against the rebar during tying.
11. User Tips
- For optimal performance and longevity, always follow the recommended operating and maintenance procedures.
- Regularly check the wire reel for any tangles or loose winding to prevent jamming.
- Ensure you have a supply of 0.8mm binding wire. For pricing and availability of wire rolls, please check with your seller or an authorized distributor.
12. Warranty and Support
To ensure product safety and reliability, any repairs, maintenance, or adjustments must be performed by an authorized Heimerdinger service center or the factory service center. Always use genuine Heimerdinger replacement parts.
For issues related to the battery protection system or any other irresoluble faults, please contact your local Heimerdinger Service Center for assistance.