1. Welcome
Thank you for purchasing the Juson Audio JTA100-N Hybrid Tube Amplifier. This amplifier is designed to provide the warm, natural sound quality of vacuum tube amplification combined with the robust performance of a modern solid-state power amplifier. It features multiple analog and digital inputs, including Bluetooth, to enhance your audio experience.
The JTA100-N is an upgraded version of the JTA100, offering enhanced headphone output capabilities and refined audio performance.
Figure 1: Juson Audio JTA100-N Integrated Tube Amplifier with remote control.
Video 1: Juson Audio JTA100-N Product Showcase.
2. Important Safety Instructions
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT OPEN.
This product contains vacuum tubes and high voltage components. Refer all servicing to qualified service personnel.
FCC STATEMENT
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
3. What's in the Box
Please check the contents of your package carefully. If anything is missing or damaged, contact your dealer immediately.
- 1 x JTA100-N Hybrid Tube Amplifier
- 1 x Remote Control
- 1 x AC Power Cable
- 1 x User Manual (This document, also available as a PDF download)
Figure 2: Package Contents.
4. Controls and Functions
4.1 Front Panel
Figure 3: Front Panel Overview.
- POWER SWITCH/INDICATOR: Turns the device on and off. The ring around the power button illuminates when the unit is turned on.
- BASS CONTROL: Adjusts the tone level for the bass output.
- TREBLE CONTROL: Adjusts the tone level for the treble output.
- VU METERS: Displays the audio output level for the left and right channels.
- DISPLAY: Shows the currently selected input (e.g., "BLUE" for Bluetooth, "AUX" for Auxiliary, "OPT" for Optical, "COAX" for Coaxial, "PHO" for Phono, "PC" for PC-USB).
- HEADPHONE OUTPUT: Connects headphones. Plugging in headphones mutes the speakers.
- VOLUME CONTROL: Adjusts the overall output volume.
- INPUT SELECTOR: Press to cycle through available input sources.
4.2 Rear Panel
Figure 4: Rear Panel Connections.
- PC-USB INPUT: Connects to a computer for digital audio input.
- DIGITAL OPTICAL INPUT (OPT): Connects to devices with optical digital audio output.
- DIGITAL COAXIAL INPUT (COAX): Connects to devices with coaxial digital audio output.
- AUX RCA INPUT (AUX): Connects to analog audio sources using RCA cables.
- PHONO RCA INPUT (PHONO): Connects to turntables with phono output.
- GROUND TERMINAL (GND): Connects the ground wire from a turntable to reduce hum.
- BLUETOOTH ANTENNA: Connect the supplied antenna for Bluetooth connectivity.
- SPEAKER OUTPUTS: Connects passive speakers.
- SUBWOOFER OUTPUT (SW OUT): Connects to an active subwoofer.
- AC VOLTAGE SELECTOR SWITCH: Selects between 110V and 220V AC power. Ensure this is set correctly for your region.
- AC POWER INPUT: Connects the supplied AC power cable.
- NOISELESS COOLING FAN: Provides cooling for internal components.
- HEADPHONE H-GAIN/L-L SWITCH: High/Low gain switch for headphone output.
4.3 Remote Control
Figure 5: Remote Control.
- POWER: Turns the amplifier on/off.
- INPUT SELECTION: Buttons for PHONO, OPT, COAX, AUX, BT, PC-USB.
- VOLUME +/-: Adjusts volume up or down.
- MUTE: Mutes/unmutes audio output.
- TRACK TRANSPORT CONTROLS: (For Bluetooth/USB playback, if supported by source device) Play/Pause, Next/Previous Track.
5. Setup Instructions
5.1 Connecting the Power Cable
- Before connecting the main power cable, ensure the AC VOLTAGE SELECTOR SWITCH on the rear panel is set correctly for your local voltage (110V or 220V). Incorrect setting can damage the amplifier.
- Connect the supplied AC power cable to the AC POWER INPUT on the rear panel and then to a wall outlet.
5.2 Connecting Speakers
The JTA100-N can power passive speakers with a minimum impedance of 4 Ohms. Use good quality speaker wire for optimal sound.
Connecting Speaker Wires (Bare Wire)
- Strip approximately 1/2 inch (1.2 cm) of insulation from each end of the speaker wire.
- Unscrew the binding post terminal on the rear of the amplifier.
- Insert the bare wire into the hole in the side of each terminal.
- Tighten the binding post terminal to secure the wire.
- Repeat for all speaker connections, ensuring correct polarity (+ to + and - to -).
Connecting Banana Plug Cables
- Insert the banana plug into the end of the binding post terminal.
- Tighten the binding post terminal to secure the connection.
- Repeat for all speaker connections, ensuring correct polarity.
NOTE: Do not connect the two speaker terminals together or to ground. This amplifier is not designed to be used in bridged mode, and attempting to do so may damage the amplifier.
5.3 Connecting a Turntable
The JTA100-N features a built-in phono preamplifier, allowing direct connection to most turntables.
- Ensure your turntable is set to output a phono signal. If your turntable outputs a line-level signal, connect it to the AUX Input instead.
- Connect the RCA cables from your turntable to the PHONO RCA INPUT on the rear panel.
- Connect the ground wire from your turntable to the GROUND TERMINAL (GND) on the rear of the amplifier to reduce hum.
Figure 6: Turntable Connection Example.
5.4 Connecting a Subwoofer
To add an active subwoofer, use a single RCA cable to connect the SW OUT on the rear panel of the JTA100-N to the input of your active subwoofer. The subwoofer output is full-range and will be affected by the main volume control.
5.5 Connecting Headphones
Headphones can be connected to the HEADPHONE OUTPUT on the front of the JTA100-N. This input has a high-low gain switch for optimal performance with various headphone impedances (16-600 ohms). Plugging in headphones automatically mutes the speaker outputs.
NOTE: To avoid damage to headphones or your hearing, ensure the volume is turned down before plugging in or unplugging headphones.
Figure 7: Headphone Connection.
5.6 Bluetooth Connection
- Connect the supplied Bluetooth antenna to the BLUETOOTH ANTENNA port on the rear panel.
- Select "BT" as the input source using the front panel input selector or the remote control. The display will show "BLUE".
- On your smartphone, tablet, computer, or other Bluetooth-enabled device, search for "JTA100-N" in the Bluetooth settings and pair with it.
- Once paired, the display will indicate a successful connection, and you can stream audio wirelessly.
6. Operating Instructions
- Power On/Off: Press the POWER SWITCH on the front panel or the remote control to turn the amplifier on or off. The power indicator ring will illuminate when on.
- Input Selection: Use the INPUT SELECTOR button on the front panel or the dedicated input buttons on the remote control (PHONO, OPT, COAX, AUX, BT, PC-USB) to choose your desired audio source.
- Volume Control: Rotate the VOLUME CONTROL knob on the front panel or use the Volume +/- buttons on the remote to adjust the listening level.
- Tone Controls: Use the BASS CONTROL and TREBLE CONTROL knobs on the front panel to fine-tune the low and high frequencies to your preference.
- Mute Function: Press the MUTE button on the remote control to temporarily silence the audio. Press it again to unmute.
- Headphone Gain: Use the HEADPHONE H-GAIN/L-L SWITCH on the rear panel to select the appropriate gain level for your headphones.
7. User Tips
- Tube Seating: If you experience issues after transportation, ensure all vacuum tubes are securely seated in their sockets. Gently press down on each tube to confirm it's fully inserted.
- Bluetooth Performance: The Bluetooth functionality is reported to be clear and warm, working well with both headphones and speakers. Ensure the antenna is properly connected for optimal range.
- Sound Quality: Users appreciate the clear and warm sound, noting the pleasant orange glow from the tubes.
8. Maintenance
- Cleaning: Use a soft, dry cloth to clean the amplifier's exterior. Do not use liquid cleaners or aerosols.
- Tube Care: Vacuum tubes have a finite lifespan. If sound quality degrades or a tube fails, they can be replaced. Ensure the amplifier is powered off and unplugged before handling tubes. Allow tubes to cool completely before removal or insertion.
- Ventilation: Ensure adequate ventilation around the amplifier to prevent overheating. Do not block the cooling fan on the rear panel.
9. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No power | Power cable not connected; AC voltage selector incorrect; Wall outlet not active. | Ensure power cable is securely connected. Check AC voltage selector switch. Test wall outlet with another device. |
| No sound from speakers | Incorrect input selected; Volume too low; Speakers not connected; Headphones plugged in; Mute activated. | Select correct input. Increase volume. Check speaker connections. Unplug headphones. Deactivate mute. |
| No sound from headphones | Headphones not fully plugged in; Volume too low; Incorrect gain setting. | Ensure headphones are fully inserted. Increase volume. Adjust headphone gain switch. |
| Humming/Buzzing sound | Ground loop; Loose connections; Turntable ground wire not connected. | Ensure all audio cables are securely connected. Connect turntable ground wire to GND terminal. Try plugging components into different outlets. |
| Bluetooth connection issues | Antenna not connected; Device too far; Interference; Not in pairing mode. | Connect Bluetooth antenna. Move device closer to amplifier. Ensure amplifier is in BT input mode and discoverable. |
| Tubes not glowing or sound issues after transport | Tubes dislodged during shipping. | Power off and unplug the amplifier. Gently press down on each tube to ensure it is fully and securely seated in its socket. |
10. Specifications
All specifications are tested by current sample. Juson Audio reserves the right to update specifications in the future without further notice.
Figure 8: Technical Specifications (as per included manual).
| Attribute | Value |
|---|---|
| Model Number | JTA100-N |
| Channels | 3 (2.1) |
| Maximum Power Output (Peak) | 260W x 2 @ 4 Ohm, 130W x 2 @ 8 Ohm |
| RMS Power Output | 100W x 2 @ 4 Ohm, 80W x 2 @ 8 Ohm |
| Total Gain | 29dB |
| THD+N | <1.5% @ Maximum Rated Output |
| Frequency Response | 15-20,000Hz (1dB) |
| Headphone Output | 130 mW*2@30 ohms; 180 mW*2@300 ohms (capable of driving 16-600 ohms) |
| Input Sensitivity | 630mV |
| Signal to Noise Ratio | 80dB |
| Preamplifier Tube | 2*6J9 + 2*5726 + 2*6N7P tubes |
| Stabilivolt Tube | WY-3P |
| Transistors | Toshiba A1943 x 4, Toshiba C5200 x 4 |
| Channel Separation | 53dB |
| Minimum Speaker Impedance | 4 Ohm |
| Tone Controls - Bass/Treble | 6dB/oct @ 200Hz and 4,000Hz |
| PC-USB | Up to 48 kHz 16Bit |
| Digital Inputs | SPDIF LPCM (up to 48kHz 16Bit) |
| Bluetooth | Version 5.0 supports SBC and AAC codecs |
| Inputs | Optical, Coaxial, Bluetooth 5.0, 2x Stereo RCA, USB |
| Output | Speaker, Subwoofer, Headphone |
| Idle Power Consumption | 45W |
| Power | 110/220 VAC, 50/60 Hz Standard IEC Connection |
| Dimensions | 330*316*169mm |
| Amplification | Class A/B |
| Origin | Mainland China |
| Certification | CE, FCC, RoHS |
11. Warranty & Support
Juson Audio warrants this product against defects in material and workmanship for ONE YEAR from the date of purchase from an authorized Juson Audio dealer. This warranty extends only to the original purchaser and is limited to the terms set forth in this warranty.
Warranty Details:
- Free Repair Service: 24 months from the date of receipt (excluding man-made damage and/or misuse).
- Tube Parts Warranty: 3 months warranty for vacuum tubes.
- Reporting Defects: Defective units MUST BE reported with photos, videos, or other evidence and returned within the warranty period.
- Return Process: You need to submit a tracking number and issue the PO number after arranging returns with original packages.
- Post-Warranty Support: After the warranty expires, Juson Audio teams are willing to offer technical support online to help you repair the product.
For any technical support or warranty claims, please contact Juson Audio Official Store directly.