EJEAS V4 Plus + V6 PRO

Contents

EJEAS Motorcycle Helmet Intercom System User Manual

Models: V4 Plus & V6 Pro+

Introduction

This manual provides comprehensive instructions for the EJEAS V4 Plus and V6 Pro+ Motorcycle Helmet Intercom Systems. It covers installation, operation, maintenance, troubleshooting, and product specifications to ensure optimal performance and user safety. Please read this manual thoroughly before using your intercom system.

Important Charging Precaution:

Always use a DC 5V-1A power charger to charge the intercom product. The maximum output power of the charger should not exceed 5W. Do not use fast chargers for these devices. (Plug not included).

Intercom unit connected to a DC5V/1A charger

Image: EJEAS intercom unit connected to a DC5V/1A charger, illustrating the correct charging method.

Important Storage Precaution:

When storing the machine, ensure it is fully charged. If it cannot be stored fully charged, it must be at least 50% charged. Prolonged undercharging will adversely affect the life of the machine and shorten its normal service life.

Package Contents

Verify that all items listed below are included in your package:

  • 2 x V4 Plus Intercom Main Unit
  • 2 x V6 Pro Intercom Main Unit
  • 4 x Universal Helmet Clamp
  • 4 x Microphone & Headset
  • 4 x Magic Tape Package
  • 2 x User Manual (Printed)
  • 4 x USB Charging Cable (Type-C)
Contents of the EJEAS intercom package including units, cables, microphones, and clamps

Image: A complete set of package contents for the EJEAS V4 Plus and V6 Pro+ intercoms, showing main units, headsets, clamps, and cables.

Setup and Installation

Helmet Clamp Installation

There are two methods for installing the intercom unit onto your helmet using the provided clamps:

Clip 1 Installation Steps (Adhesive Mount)

  1. Clean the desired mounting area on the helmet.
  2. Peel off the protective film from the adhesive pad on the clip.
  3. Firmly press the clip onto the helmet surface.
  4. Slide the intercom unit onto the mounted clip until it clicks into place.
Four-step diagram showing adhesive helmet clamp installation

Image: Step-by-step visual guide for installing the intercom unit using the adhesive helmet clamp.

Clip 2 Installation Steps (Clip Mount)

  1. Position the clip mount on the edge of your helmet.
  2. Secure the clip by tightening the screws or engaging the locking mechanism.
  3. Slide the intercom unit onto the mounted clip until it clicks into place.
Four-step diagram showing clip-on helmet clamp installation

Image: Step-by-step visual guide for installing the intercom unit using the clip-on helmet clamp.

Headset Installation

  1. Connect the headset cable to the Type-C charging port/headphone jack on the intercom unit. Ensure it is fully inserted.
  2. Position the speakers inside the helmet, aligning them with your ears. Use the provided magic tape if necessary to secure them.
  3. Route the microphone to a suitable position near your mouth, ensuring it is clear of obstructions.
  4. Tuck away any excess cables within the helmet padding for comfort and safety.
Four-step diagram showing headset and microphone installation inside a helmet

Image: Visual instructions for connecting the headset and positioning the speakers and microphone inside a helmet.

Operating Instructions

EJEAS V4 Plus Operations

EJEAS V4 Plus intercom unit with labeled buttons: A Button, Volume+, FM Button, Indicator Light, B Button, Volume-, Phone/Power button, Type-C charging port/Headphone jack, Antennae

Image: Diagram of the EJEAS V4 Plus unit, highlighting its buttons and ports.

Basic Operations (V4 Plus)

  • Power On: Long press the Phone Button.
  • Power Off: Click the FM Button + Phone Button simultaneously.

Intercom Pairing Operations (V4 Plus)

  • Pairing 2 Machines: Long press A Button for No.1 machine, long press B Button for No.2 machine.
  • Pairing 3 Machines: After pairing 2 machines, long press A Button for No.2 machine, long press B Button for No.3 machine, then click A Button for No.1 machine.
  • Pairing 4 Machines: After pairing 3 machines, long press A Button on machine 3, long press B Button on machine 4. After successful pairing, click A Button on machine 1 and B Button on machine 2 respectively.
  • Intercom Disconnect: Long press the corresponding A/B button.
  • Intercom Reconnect: Click the corresponding A/B button.

Mobile Phone Pairing (V4 Plus)

  • Connection: Long press the Phone Button.
  • Answer Call: Automatically answers within 8 seconds, or click the Phone Button.
  • Reject Call: Long press the Phone Button.
  • End Code Replay: Double-click the Phone Button.
  • Hang Up Call: Click the Phone Button.
  • Voice Assistant: Long press the Phone Button.
  • Play/Pause: Click the Phone Button.
  • Volume: Click Volume+ / Volume-.
  • Previous/Next Song: Long press Volume+ / Volume-.
  • Radio On/Off: Long press the FM Button.
  • Switch Radio Channel: Long press Volume+ / Volume-.

Other Operations (V4 Plus)

  • Clear Pairing: Press and hold Phone Button + Volume+ + Volume- simultaneously.
  • Pairing Handle (EUC Remote Control): Long press Phone Button + B Button.

Handle EUC Pairing (V4 Plus - Optional Accessory)

EJEAS EUC remote control diagram with buttons A, B, +, -, FM, Phone

Image: Diagram of the EJEAS EUC remote control, showing its buttons.

  • Clear EUC Pairing Record: Long press FM Button + Volume- on the EUC.
  • Pairing EUC: Long press Phone Button + B Button on the intercom machine. Then, click any key on the EUC.
  • Volume+ (EUC): Click to control volume, long press for next song.
  • Volume- (EUC): Click to control volume, long press for previous song.
  • Phone Button (EUC): Click to answer/hang up call, music pause/playback, connect back to last connected mobile phone. Long press for voice assistant/cancel dialing. Double-click to redial last digit.
  • A Button (EUC): Click for intercom A pairing. Long press to disconnect intercom. No operation for other functions.
  • B Button (EUC): Click for intercom B pairing. Long press to disconnect intercom. No operation for other functions.
  • FM Button (EUC): Click to turn FM on or off.

EJEAS V6 Pro+ Operations

EJEAS V6 Pro+ intercom unit with labeled buttons: B Button, Power Off Button, Volume-, Phone Button, C Button, Volume+, Headphone Jack Type-C Interface, E Button, Moto Button/A Button (Power on Button), D Button, Antennae

Image: Diagram of the EJEAS V6 Pro+ unit, highlighting its buttons and ports.

Basic Operations (V6 Pro+)

  • Power On: Long press the Moto Button.
  • Power Off: Click the Power Off Button.

Intercom Pairing Operations (V6 Pro+)

  • Pair A: Long press main device Moto Button + A device Moto Button.
  • Pair B: Long press main device B Button + B device B Button.
  • Pair C: Long press main device C Button + C device C Button.
  • Pair D: Long press main device D Button + D device D Button.
  • Pair E: Long press the main device E Button + E device E Button.
  • Switching Intercom: Press the letter button of the corresponding device (A, B, C, D, or E).

Mobile Phone Pairing (V6 Pro+)

  • Connection: Long press the Phone Button.
  • Call Reject: Click the Phone Button.
  • Call Hang Up: Click the Phone Button.
  • End Code Replay: Long press the Phone Button.
  • Cancellation of Replay: Click the Phone Button.
  • Voice Assistant: Double-click the Phone Button.
  • Play/Pause: Click the Phone Button.
  • Previous/Next Song: Long press Volume- / Volume+.
  • Volume Up/Down: Click Volume+ / Volume-.

Other Operations (V6 Pro+)

  • Clear Pairing: Press and hold Phone Button + B Button simultaneously.
  • Connect to APP: Long press the Phone Button.

Bluetooth Pairing (V6 Pro+ - Other Brands)

  • Pairing with other brands of intercoms/Bluetooth headsets: Long press Moto Button + Volume-, then click Moto Button to search.

Handle EUC Pairing (V6 Pro+ - Optional Accessory)

EJEAS EUC remote control diagram with buttons A, B, +, -, FM, Phone

Image: Diagram of the EJEAS EUC remote control, showing its buttons.

  • Clear EUC Pairing Record: Long press FM Button + Volume- on the EUC.
  • Pairing EUC: Long press Phone Key + E Key on the intercom machine. Then, click any key on the EUC.
  • Volume+ (EUC): Click to control volume, long press for next song.
  • Volume- (EUC): Click to control volume, long press for previous song.
  • Phone Button (EUC): Click to answer/hang up call, music pause/playback, connect back to last connected mobile phone. Long press for voice assistant/cancel dialing. Double-click to redial last digit.
  • A Button (EUC): Click for intercom A pairing. Long press to disconnect intercom. Double click for intercom D pairing.
  • B Button (EUC): Click for intercom B pairing. Long press to disconnect intercom. Double tap for intercom E pairing.
  • C Button (EUC): Click to pair C. Long press to disconnect. Double click for no operation.
  • FM Button (EUC): No operation.

Key Features

Both EJEAS V4 Plus and V6 Pro+ models offer advanced features for an enhanced riding experience:

  • Bluetooth 5.1 Technology: Provides stable communication and low energy consumption.
  • CVC Noise Reduction Technology: Intelligently reduces environmental noise for clearer communication.
  • High Fidelity Speakers: Deliver 3D sound for clear audio.
  • IP65 Waterproof: Designed to withstand various weather conditions.
  • Mobile Phone Connectivity: Pair with up to two mobile phones for calls, music, and navigation. Supports voice assistant.
  • Built-in FM Radio: Enjoy radio broadcasts within the 76MHz to 108MHz range.
Close-up of a Bluetooth 5.1 chip, indicating new upgrade technology

Image: Visual representation of the upgraded Bluetooth 5.1 technology for smoother and more stable connections.

Diagram showing sound waves before and after CVC noise reduction

Image: Illustration of CVC Noise Reduction Technology, demonstrating how environmental noise is filtered for clearer audio.

Diagram showing sound waves entering an ear from two speakers, representing high fidelity audio

Image: Diagram illustrating the high-fidelity speaker output for immersive 3D sound.

EJEAS intercom unit being splashed with water, demonstrating IP65 waterproof rating

Image: The intercom unit being splashed with water, indicating its IP65 waterproof capability.

Smartphone screens showing calling, map, and music apps, representing mobile phone connectivity

Image: Screens depicting mobile phone functions like calling, navigation, and music, accessible via the intercom.

FM radio tuner interface showing frequency range 76MHz to 108MHz

Image: A visual representation of the built-in FM radio function, showing the frequency range.

Maintenance

  • Cleaning: Use a soft, damp cloth to clean the exterior of the intercom unit. Do not use harsh chemicals or abrasive cleaners.
  • Water Exposure: While the units are IP65 waterproof, ensure the headphone interface is fully inserted to prevent water ingress. Avoid submerging the device.
  • Storage: When not in use for extended periods, ensure the intercom is fully charged (or at least 50% charged) before storing. Store in a cool, dry place away from direct sunlight and extreme temperatures.

Troubleshooting

ProblemPossible CauseSolution
Device does not power on.Low battery or incorrect power-on procedure.Charge the device fully. Ensure you are long pressing the correct power button (Phone Button for V4 Plus, Moto Button for V6 Pro+).
Cannot pair with another intercom.Incorrect pairing procedure or existing pairing conflicts.Follow the specific pairing instructions for your model (V4 Plus or V6 Pro+). Try clearing all previous pairings before attempting a new one.
Cannot connect to mobile phone.Bluetooth not enabled on phone, device not in pairing mode, or previous connection issues.Ensure Bluetooth is active on your phone. Put the intercom in mobile phone pairing mode (long press Phone Button). Clear existing Bluetooth connections on both devices and try again.
Poor audio quality or noise.Microphone/speaker placement, CVC not active, or environmental interference.Adjust microphone and speaker positions. Ensure CVC noise reduction is functioning. Check for strong electromagnetic interference.
EUC remote control not responding.EUC not paired or low battery.Follow the EUC pairing instructions for your specific intercom model. Ensure the EUC has sufficient power.

Specifications

EJEAS V4 Plus Specifications

FeatureDetail
ModelV4 Plus
Intercom RidersUp to 4 people
Bluetooth Version5.1
FM FunctionYes (76MHz ~ 108MHz)
Voice PromptYes
Adaptable HandleEUC (optional accessory)
Intercom Distance1500 meters (4 sets of distance)
Charging InterfaceType-C
Waterproof GradeIP65
Charger SpecificationDC5V/1A (charger not included)
Working Voltage3.7V
Battery Capacity750mAh
Charging Time2 hours
Standby Time150 hours
Intercom Time18 hours
Music Time24 hours
Mobile Phone Connection Distance10 meters
Working Temperature-10°C to 50°C
Special FeaturesWaterproof, CVC Noise Reduction, High Fidelity Speaker
Item Weight0.6 kg
Item Dimensions (L x W x H)8.5 cm x 4.5 cm x 1.5 cm
External Testing CertificationCE
Applicable Helmet TypeHalf Helmet
Power Supply ModeBuilt-in Battery
Connection ModeWire
Comparison table of EJEAS V4 Plus vs V4 Pro features

Image: A comparison table highlighting the advanced features of the V4 Plus over the older V4 Pro model.

EJEAS V6 Pro+ Specifications (Key Differences)

  • Model: V6 Pro+
  • Intercom Riders: Support 6 riders (2 riders talk simultaneously, 1 main device pairs with 5 sub-devices)
  • Intercom Distance: 800 meters
  • Music Time: 25 hours
  • Standby Time: 260 hours
Icons representing key features of the EJEAS V6 Pro+ intercom

Image: Icons summarizing the product features of the EJEAS V6 Pro+, including Bluetooth 5.1, 2-way intercom, 800m range, FM radio, and more.

Motorcyclists on a road with an 800-meter communication range indicated

Image: Depiction of the 800-meter communication distance for the V6 Pro+ model.

Diagram showing six helmet icons connected for multi-way intercom

Image: Diagram illustrating the multi-way intercom capability supporting up to six riders.

User Tips

  • For optimal sound quality, ensure speakers are positioned directly over your ears and the microphone is close to your mouth, away from direct wind.
  • Regularly check the battery level, especially before long rides, to avoid unexpected power loss.
  • If experiencing pairing difficulties, try clearing all previous pairings on both devices and restarting them before attempting to pair again.
  • Keep the firmware updated if new versions become available through the EJEAS app or website for improved performance and features.

Warranty and Support

For detailed warranty information and technical support, please refer to the official EJEAS website or contact their customer service. A comprehensive user manual in PDF format is also available for download:

Download User Manual (PDF)

For further assistance, please visit www.ejeas.com.

© 2024 EJEAS. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.