1. Introduction
Thank you for choosing the EightFox Car Rear View Camera. This camera is designed to provide a clear, wide-angle view of the area behind your vehicle, enhancing safety during reversing and parking maneuvers. It features high-definition imaging, night vision capabilities, and a durable waterproof design. Please read this manual carefully before installation and use to ensure proper operation and longevity of your device.
2. Package Contents
Please check the package for the following items:
- EightFox Car Rear View Camera
- Video Cable (6 meters)
- Power Cable

3. Setup and Installation
Proper installation is crucial for optimal performance. It is recommended to have this product installed by a professional if you are unsure about the wiring process.
3.1. Wiring Diagram
Follow the wiring diagram below to connect your camera to your vehicle's electrical system and display unit.

- Connect the navigation video input plug.
- Connect the navigation reverse detection line (BACK or REVERSE).
- Docking with the reversing light, connecting the positive pole of the reversing light.
- Connect the body screws or iron or the negative pole of the reversing light (ground).
3.2. Display Screen Compatibility
Ensure your display screen is compatible with the camera's video signal type (CVBS or AHD).
3.2.1. CVBS Camera Compatibility
CVBS cameras are compatible with a wide range of display screens, including 4.3-inch, 5-inch, 7-inch, and 9-inch desktop displays, rearview mirror displays, and older style DVD navigation units (consoles that can hold discs).

3.2.2. AHD Camera Compatibility
AHD cameras are only suitable for AHD-compatible displays, typically Android head units that have an application and a built-in AHD25 FPS channel. If your display cannot select AHD, it does not support AHD cameras.

To configure for AHD: Go to Car settings >> Factory settings >> Reverse (picture) settings >> Select AHD 1080P or AHD 720P.
3.3. Conversion Line Control
Your camera may feature control wires to switch between different modes:
- White Cable: Mirror control (Rear view ↔ Front view)
- Brown Cable: Signal control (AHD ↔ CVBS)
- Green Cable: Parking line switch (On ↔ Off)
To change a setting, carefully cut the corresponding wire. For example, to switch from AHD to CVBS, cut the brown wire. To disable parking lines, cut the green wire.


4. Operating Instructions
4.1. Video Signal Selection (AHD/CVBS)
If your camera supports both AHD and CVBS signals, you can switch between them by cutting the brown control wire. Ensure your display unit is set to the corresponding signal type.
To set your Android head unit for CVBS: Go to Car Setting >> Factory Setting >> Reverse (Picture) Setting >> Select CVBS NTSC.

4.2. Parking Line Control
Some camera models come with switchable parking lines. To enable or disable the parking lines, cut the green control wire.
4.3. Mirror Control
To switch the camera view from rear to front (or vice-versa), cut the white control wire.
4.4. Dynamic Trajectory Guidelines
Certain camera models feature dynamic trajectory guidelines that adjust automatically based on the car's movement and steering wheel control. If you wish to disable this feature, cut the white control line (this may be the same white line as mirror control, depending on the model).

Video 4.1: Demonstration of the camera's view and dynamic trajectory lines.
5. Maintenance
To ensure clear vision and extend the life of your camera:
- Regularly clean the camera lens with a soft, damp cloth. Avoid abrasive cleaners.
- Ensure the camera is securely mounted and all connections are tight.
- The camera is IP68 waterproof, designed to withstand rain and car washes, but avoid high-pressure water jets directly on the lens for extended periods.

6. Troubleshooting
- No Signal/Black Screen: Check all cable connections, especially the video input to the monitor and the power supply to the camera. Ensure the camera is receiving 12V power. Verify the monitor is set to the correct video input channel.
- Distorted/Flickering Image: Check for loose connections. Ensure the video signal type (AHD/CVBS) matches your monitor's setting. Check for electrical interference from other car components.
- Parking Lines Not Appearing/Incorrect: If your camera has switchable parking lines, ensure the green control wire is in the desired state (cut/uncut). If dynamic lines are incorrect, ensure proper installation and check for any specific calibration steps for your head unit.
- Image is Mirrored: If the image is horizontally flipped, check the white control wire for mirror control and adjust as needed.
7. Specifications
| Feature | Specification |
|---|---|
| Brand Name | EightFox |
| Lens Material | Glass |
| Shell Material | Plastic |
| Material | ABS |
| Video Signal | AHD / CVBS (Switchable on some models) |
| Video Pixel | 720P / 1080P (Model dependent) |
| Viewing Angle | 170° (Model dependent) |
| Guiding Line | Yes (Static or Dynamic, switchable on some models) |
| Alarm Type | Rear Side |
| Length of Video Cable | 6M |
| Waterproof Rating | IP68 |
| Certification | CE |
| Origin | Mainland China |

8. User Tips
- Before finalizing installation, test the camera's functionality and all switchable features (parking lines, mirror view, signal type) to ensure they operate as desired.
- When cutting control wires, ensure the vehicle's power is off to prevent short circuits.
- For a detailed user manual and additional guidance, please refer to the PDF document available from the seller.
9. Warranty and Support
EightFox products are manufactured to high-quality standards. If you encounter any issues with your product, please contact the seller directly for support and warranty information. Our technical team is available to assist with any problems you may experience.