1. Introduction
Thank you for purchasing the Baofeng UV-9R EU Amateur Portable Radio. This high-performance, stable wireless two-way radio is factory-developed with an IP45 water-resistant rating, making it suitable for various outdoor and industrial working scenarios. This manual provides detailed instructions to help you derive maximum performance from your radio.
2. Safety Information
The following safety precautions must always be observed during operation, service, and repair of this equipment:
- This equipment shall be serviced by qualified technicians only.
- Do not modify the radio for any reason.
- Use only supplied or approved batteries and chargers.
- Do not use any portable radio that has a damaged antenna. If a damaged antenna comes into contact with your skin, a minor burn can result.
- Turn off your radio prior to entering any area with explosive and flammable materials.
- Do not charge your battery in a location with explosive and flammable materials.
- To avoid electromagnetic interference and/or compatibility conflicts, turn off your radio in any area where posted notices instruct you to do so.
- Turn off your radio before boarding an aircraft. Any use of a radio must be in accordance with airline regulations or crew instructions.
- Turn off your radio before entering a blasting area.
- For vehicles with an air bag, do not place a radio in the area over an air bag or in the air bag deployment area.
- Do not expose the radio to direct sunlight over a long time, nor place it close to heating source.
- When transmitting with a portable radio, hold the radio in a vertical position with the microphone 3 to 4 centimeters away from your lips. Keep antenna at least 2.5 centimeters away from your body when transmitting.
WARNING: If you wear a radio on your body, ensure the radio and its antenna are at least 2.5 centimeters away from your body when transmitting.
3. Features and Functions
The Baofeng UV-9R EU is an IP45 dust and water-resistant two-way radio, ensuring reliability in wet environments. It features:
- Dual-band handheld transceiver: With display function menu on the "LCD".
- Working Frequency: VHF 130-176MHz & UHF 400-520MHz.
- High power/mid/low: (5W/3W/1W) selectable.
- Memory Channels: Up to 128.
- Cross band reception/transmission.
- Display Options: A variety of display channel number, frequency, channel name, etc.
- CTCSS & DCS.
- Tone end of transmission.
- VOX (Voice Operated Transmission) function.
- DTMF emergency alarm.
- ANI code.
- Selectable Frequency Step: 2.5/5/6.25/10/12.5/20/25/50 kHz.
- Frequency reverse.
- Battery saving function "SAVE".
- Emergency SOS sound and light alarm.
- Programmable by PC.
- Broadband (Wide 25KHz) / Narrowband (Narrow 12.5KHz), selectable.
- Commercial FM radio receiver: (65 MHz ~ 108 MHz).
- Display illumination and programmable keyboard.
- Built-in LED flashlight.
4. Package Contents
Carefully unpack the transceiver and identify the following items. If any items are missing or damaged, contact your dealer immediately.
- 1 × Baofeng UV-9R EU Radio
- 1 × High Gain Antenna
- 1 × 1800mAh Battery (Note: Seller description mentions 2200mAh, but product specs indicate 1800mAh. Please verify.)
- 1 × EU Plug Charger
- 1 × Belt Clip
- 1 × English User Manual (PDF available at User manual (PDF))
- Optional accessories (may vary by region): Power Cord, Lapel Speaker-Microphone, Program Cable, Earbud Microphone.
5. Setup
5.1. Installing the Antenna
Install the antenna by turning it clockwise onto the radio's connector until it stops. Do not rotate it by its top; hold it by its base. Never transmit without an antenna.
5.2. Installing the Belt Clip
If necessary, install the belt clip at the rear of the battery compartment cover using the provided screws. Do not use glue to fix the screw, as solvents may damage the battery casing.
5.3. Micro-Headset Installation
Plug the external micro-headset connector into the "SP. & MIC" jack of the transceiver.
5.4. Battery Installation
- Align the battery with the guide rails on the aluminum chassis.
- Slide it upwards until a "click" is heard, indicating the battery latch has locked it in place.
To remove the battery: Turn off the radio. Slide the battery latch at the bottom of the radio's body in the direction indicated by the arrow. Slide down the battery for about 1 to 2 centimeters, then remove it.
5.5. Battery Charging
Use only the charger specified by the manufacturer. The charger's LED indicates the charging progress:
| Charging Status | LED Indication |
|---|---|
| Standby (no-load) | Red LED flashes, while Green LED glows |
| Charging | Red LED solidly glows |
| Fully Charged | Green LED solidly glows |
| Error | Red LED flashes, while Green LED glows |
Charging Steps:
- Plug the power cord into the adapter.
- Plug the AC connector of the adapter into the AC outlet socket.
- Plug the DC connector of the adapter into the DC socket on the back of the charger.
6. Battery Information
6.1. Initial Use
New batteries are shipped uncharged. Charge a new battery for 5 hours before initial use. Maximum battery capacity and performance are achieved after three full charge/discharge cycles. Recharge the battery if power runs low.
WARNING: To reduce the risk of injury, charge only the battery specified by the manufacturer. Other batteries may burst, causing bodily injury and property damage. Do not dispose of batteries in a fire. Dispose of batteries according to local regulations (e.g., recycling). Never attempt to disassemble the battery.
6.2. Battery Tips
- Charge batteries at temperatures between 5°C and 40°C.
- Turn off the radio when charging a battery attached to it for a full charge.
- Do not cut off power or remove the battery during charging.
- Never charge a wet battery; dry it with a soft cloth first.
- Replace the battery when operating time is noticeably shorter than normal.
6.3. Prolong Battery Life
- Battery performance decreases below 0°C; a spare battery is recommended in cold weather.
- Clean battery contacts with a dry cloth to prevent charging issues.
6.4. Battery Storage
- Fully charge the battery before long-term storage to prevent over-discharge damage.
- Recharge Li-Ion batteries every 6 months during storage to prevent capacity reduction.
- Store batteries in a cool, dry place at room temperature to reduce self-discharge.
7. Parts, Controls, and Keys
| No. | Part | No. | Part |
|---|---|---|---|
| 1 | Antenna | 6 | Speaker |
| 2 | LCD | 7 | Microphone |
| 3 | Keypad | 8 | Battery latch |
| 4 | Knob (ON/OFF, volume) | 9 | PTT |
| 5 | Flashlight | 10 | SK-side key1/F |
| 11 | SK-side key2/M | ||
| 12 | Strap buckle | ||
| 13 | Accessory jack | ||
| 14 | LED indicator |
7.1. Command/Key Definition
- Power On: Rotate PWR/VOL Switch clockwise. You will hear a "Beep" and the radio will report the current channel.
- [SOS] Emergency Alarm: Long press [SOS] to activate the alarm (green and red lights flash, hand lamp shines). Press again to release.
- [PTT] (Push-to-Talk): Press and hold to transmit, talk into the microphone. Release to receive.
- SK-SIDE KEY1/[F]: Press [F] to activate/deactivate FM Radio.
- SK-SIDE KEY2/[M]: Press [M] to turn on/off the flashlight. Press and hold [M] to monitor the signal.
- [MENU] key: Enter the radio menu and confirm settings. Press and hold [MENU] then power on to switch between frequency and channel mode.
- [▲]/[▼] key: Press for frequency up/down. Press and hold for fast scanning.
- [EXIT/AB] key: Cancel/clear or exit. Switch between Channel A and B. In FM radio mode, switch between 65-75MHz/76-108MHz bands.
- Numeric Keypad: Used for programming radio lists and non-standard CTCSS. In transmission mode, send signal codes (set by PC software).
8. LCD Display
The display icons appear when certain operations or specific features are activated:
| Icon | Description |
|---|---|
| + | Frequency Shift + |
| - | Frequency Shift - |
| +- | Frequency offset direction for accessing repeaters. |
| S | Dual Watch/Dual Reception functions activated. |
| VOX | Function 'VOX' enabled. |
| R | Reverse function activated. |
| N | Wide Band selected. |
| ... | Battery Level indicator |
| Keypad lock function activated. | |
| L | Low transmit power. |
| Operation frequency. | |
| Yull | Signal Strength Level. |
| Operating channel. | |
| 75 25 | Operating frequency. |
| CT | 'CTCSS' activated. |
| DCS | 'DCS' activated. |
9. Basic Operation
9.1. Radio On-Off/Volume Control
Ensure the antenna and battery are correctly installed and charged. Rotate the PWR/VOL knob clockwise to turn the radio on. Continue rotating to adjust the volume. Rotate counter-clockwise until a 'click' is heard to turn the radio off.
9.2. Transmit and Receive
Select the desired channel or enter the frequency. Press and hold the PTT button to transmit, then speak into the microphone. Release PTT to receive. The LCD will show 'L', 'M', or 'H' indicating low, mid, or high power during transmission.
9.3. VOX (Voice Operated Transmission) Function
VOX allows transmission without pressing PTT, activating automatically when voice is detected. Adjust VOX Gain (levels 1-10) for smooth transmission. To enable/disable: Press [MENU], navigate to Function 4 (VOX), select level, confirm with [MENU].
9.4. Auto-Lock (Keypad Locked Automatically)
This feature prevents accidental key presses. To enable/disable: In standby, press [MENU] + number key 24, then select ON or OFF, confirm with [MENU], and exit with [EXIT].
9.5. VFO/Channel Mode
Turn off the radio. Press [MENU] and rotate the sound knob to turn on the radio. The LCD will show the channel number in the lower right corner, indicating channel mode. You can switch between VFO (Frequency) and Channel mode this way. Use [▲]/[▼] keys to select frequency/channel.
9.6. TDR (Dual Watch/Dual Reception)
This feature allows monitoring two frequencies (A and B). The transceiver periodically checks for signals on the scheduled frequency. To enable/disable: In standby, press [MENU] + [7TDR], select ON or OFF, confirm with [MENU], and exit with [EXIT].
9.7. DEL-CH (Delete Channel)
To delete a stored channel: In standby, press [MENU] + [Number key 28], select the channel, confirm with [MENU], and exit with [EXIT].
9.8. MEM-CH (Stored In Memory Channel)
To store a frequency and its parameters: In standby, press [MENU] + [Number key 27], select the desired channel order, confirm with [MENU], and exit with [EXIT].
9.9. CTCSS/DCS Scanning
Before scanning, ensure you have an RX frequency and Dual Standby is off, and the radio is in VFO mode. Go to MENU 11, press [MENU], then [*/SCAN]. Press PTT on another radio to initiate CTCSS scanning. Once scanning stops, press [MENU] to store the CTCSS.
9.10. Repeater Tail Tone
Repeaters retransmit information on a different frequency. The courtesy tone indicates repeater activity. MENU 35, 36, and 37 are helpful for repeater use. MENU 35 and 36 should be OFF. MENU 37 parameter is 1-10, with 5 being a good setting.
9.11. CTCSS/DCS
CTCSS (Continuous Tone Coded Squelch) and DCS (Digital Coded Squelch) are used to establish communication within a closed user group on a particular frequency. The squelch opens only when receiving a signal with the same CTCSS/DCS codes programmed in your transceiver. Note: Using CTCSS/DCS does not guarantee complete confidentiality of communication.
| NO | Tone (Hz) | NO | Tone (Hz) | NO | Tone (Hz) | NO | Tone (Hz) | NO | Tone (Hz) |
|---|---|---|---|---|---|---|---|---|---|
| 1 | 67.0 | 11 | 94.8 | 21 | 131.8 | 31 | 171.3 | 41 | 203.5 |
| 2 | 69.3 | 12 | 97.4 | 22 | 136.5 | 32 | 173.8 | 42 | 206.5 |
| 3 | 71.9 | 13 | 100.0 | 23 | 141.3 | 33 | 177.3 | 43 | 210.7 |
| 4 | 74.4 | 14 | 103.5 | 24 | 146.2 | 34 | 179.9 | 44 | 218.1 |
| 5 | 77.0 | 15 | 107.2 | 25 | 151.4 | 35 | 183.5 | 45 | 225.7 |
| 6 | 79.7 | 16 | 110.9 | 26 | 156.7 | 36 | 186.2 | 46 | 229.1 |
| 7 | 82.5 | 17 | 114.8 | 27 | 159.8 | 37 | 189.9 | 47 | 233.6 |
| 8 | 85.4 | 18 | 118.8 | 28 | 162.2 | 38 | 192.8 | 48 | 241.8 |
| 9 | 88.5 | 19 | 123.0 | 29 | 165.5 | 39 | 196.6 | 49 | 250.3 |
| 10 | 91.5 | 20 | 127.3 | 30 | 167.9 | 40 | 199.5 | 50 | 254.1 |
DCS Table:
| No | Code | No | Code | NO | Code | NO | Code | NO | Code |
|---|---|---|---|---|---|---|---|---|---|
| 1 | D023N | 22 | D131N | 43 | D251N | 64 | D371N | 85 | D532N |
| 2 | D025N | 23 | D132N | 44 | D252N | 65 | D411N | 86 | D546N |
| 3 | D026N | 24 | D134N | 45 | D255N | 66 | D412N | 87 | D565N |
| 4 | D031N | 25 | D143N | 46 | D261N | 67 | D413N | 88 | D606N |
| 5 | D032N | 26 | D145N | 47 | D263N | 68 | D423N | 89 | D612N |
| 6 | D036N | 27 | D152N | 48 | D265N | 69 | D431N | 90 | D624N |
| 7 | D043N | 28 | D155N | 49 | D266N | 70 | D432N | 91 | D627N |
| 8 | D047N | 29 | D156N | 50 | D271N | 71 | D445N | 92 | D631N |
| 9 | D051N | 30 | D162N | 51 | D274N | 72 | D446N | 93 | D632N |
| 10 | D053N | 31 | D165N | 52 | D306N | 73 | D452N | 94 | D645N |
| 11 | D054N | 32 | D172N | 53 | D311N | 74 | D454N | 95 | D654N |
| 12 | D065N | 33 | D174N | 54 | D315N | 75 | D455N | 96 | D662N |
| 13 | D071N | 34 | D205N | 55 | D325N | 76 | D462N | 97 | D664N |
| 14 | D072N | 35 | D212N | 56 | D331N | 77 | D464N | 98 | D703N |
| 15 | D073N | 36 | D223N | 57 | D332N | 78 | D465N | 99 | D712N |
| 16 | D074N | 37 | D225N | 58 | D343N | 79 | D466N | 100 | D723N |
| 17 | D114N | 38 | D226N | 59 | D346N | 80 | D503N | 101 | D731N |
| 18 | D115N | 39 | D243N | 60 | D351N | 81 | D506N | 102 | D732N |
| 19 | D116N | 40 | D244N | 61 | D356N | 82 | D516N | 103 | D734N |
| 20 | D122N | 41 | D245N | 62 | D364N | 83 | D523N | 104 | D743N |
| 21 | D125N | 42 | D246N | 63 | D365N | 84 | D526N | 105 | D754N |
10. Shortcut Menu Operation
The radio features a shortcut menu for quick access to settings:
- Press the [MENU] key, then use [▲] or [▼] to select the desired menu item.
- Press [MENU] again to enter parameter setting.
- Use [▲] or [▼] to select the desired parameter.
- Press [MENU] to confirm and save. Press [EXIT] to cancel or clear input.
Note: Under channel mode, certain menu settings (CTCSS, DCS, W/N, PTT-ID, BCL, SCAN ADD TO, S-CODE, CHANNEL NAME) are invalid. Only H/L power can be changed by pressing #.
11. Set Menu Description
The following table details the available menu functions and their settings:
| Menu | Function/Description | Available settings |
|---|---|---|
| 0 | SQL (Squelch level) | 0-9 |
| 1 | STEP (Frequency step) | 2.5/5/6.25/10/12.5/20/25/50kHz |
| 2 | TXP (Transmit power) | HIGH/MID/LOW |
| 3 | SAVE (Battery save, 1:1/1:2/1:3/1:4) | OFF/1/2/3/4 |
| 4 | VOX (Voice operated transmission) | OFF/1-10 |
| 5 | W/N (Wideband/narrowband) | WIDE/NARR |
| 6 | ABR (Display illumination) | OFF/1/2/3/4/5s |
| 7 | TDR (Dual watch/dual reception) | OFF/ON |
| 8 | BEEP (Keypad beep) | OFF/ON |
| 9 | TOT (Transmission timer) | 15/30/45/60.../585/600seconds |
| 10 | R-DCS (Reception digital coded squelch) | OFF/D023N...D754I |
| 11 | R-CTS (Reception Continuous Tone Coded Squelch) | 67.0Hz...254.1Hz |
| 12 | T-DCS (Transmission digital coded squelch) | OFF/D023N...D754I |
| 13 | T-CTS (Transmission Continuous Tone Coded Squelch) | 67.0Hz...254.1Hz |
| 14 | VOICE (Voice prompt) | OFF/ON |
| 15 | ANI (Automatic number identification of the radio, only can be set by PC software.) | |
| 16 | DTMFST (The DTMF tone of transmitting code.) | OFF/DT-ST/ANI-ST/DT+ANI |
| 17 | S-CODE (Signal code, only could be set by PC software.) | 1,......, 15 groups |
| 18 | SC-REV (Scan resume method) | TO/CO/SE |
| 19 | PTT-ID (press or release the PTT button to transmit the signal code) | OFF/BOT/EOT/BOTH |
| 20 | PTT-LT (delay the signal code sending) | 0,......,30ms |
| 21 | MDF-A (under channel mode, A channel displays. Note:name display only can be set by PC software.) | FREQ/CH/NAME |
| 22 | MDF-B (under channel mode, B channel displays. Note:name display only can be set by PC software.) | FREQ/CH/NAME |
| 23 | BCL (busy channel lockout) | OFF/ON |
| 24 | AUTOLK (keypad locked automatically) | OFF/ON |
| 25 | SFT-D (direction of frequency shift) | OFF/+/- |
| 26 | OFFSET (frequency shift) | 00.000...69.990 |
| 27 | MEMCH (stored in memory channels) | 000,...127 |
| 28 | DELCH (delete the memory channels) | 000,...127 |
| 29 | WT-LED (illumination display color of standby) | OFF/BLUE/ORANGE/PURPLE |
| 30 | RX-LED (illumination display color of reception) | OFF/BLUE/ORANGE/PURPLE |
| 31 | TX-LED (illumination display color of transmitting) | OFF/BLUE/ORANGE/PURPLE |
| 32 | AL-MOD (alarm mode) | SITE/TONE/CODE |
| 33 | BAND (band selection) | VHF/UHF |
| 34 | TX-AB (transmitting selection while in dual watch/reception) | OFF/A/B |
| 35 | STE (Tail Tone Elimination) | OFF/ON |
| 36 | RP_STE (Tail tone elimination in communication through repeater) | OFF/1,2,3...10 |
| 37 | RPT_RL (Delay the tail tone of repeater) | OFF/1,2,3...10 |
| 38 | PONMGS (Boot display) | FULL/MGS |
| 39 | ROGER (tone end of transmission) | ON/OFF |
| 40 | A/B-BP (Tone end of reception) | OFF/A/B |
| 41 | RESET (Restore to default setting) | VFO/ALL |
11.1. Reset (Restore To Default Setting)
The transceiver has a menu to reset VFO and ALL messages. RESET VFO returns all parameters to factory default. RESET ALL returns all transceiver and channel parameters to factory default.
To reset: In standby, press [MENU] + [Number Key 40], then select VFO or ALL, confirm with [MENU], and exit with [EXIT].
11.2. Copying (Cloning)
To copy settings from Radio A to Radio B:
- Connect the two radios with a special data cable.
- Turn on Radio B.
- Press [MONI] on Radio B. Simultaneously, turn on Radio A. The screen will show "COPYING". Once finished, Radio B will power off and then on automatically.
Repeat steps 2 and 3 to clone more radios. If cloning fails, turn off both radios, and ensure they are correctly connected with the clone cable.
12. Maintenance
Regular maintenance ensures optimal performance and longevity of your Baofeng UV-9R EU Walkie Talkie.
- Cleaning: Use a soft, damp cloth to clean the radio's exterior. Avoid harsh chemicals or abrasive cleaners.
- Battery Care: Follow the battery tips and storage guidelines in Section 6 to maximize battery life.
- Antenna: Ensure the antenna is securely attached. Avoid bending or damaging it.
- Storage: Store the radio in a cool, dry place away from direct sunlight and extreme temperatures when not in use for extended periods.
13. Troubleshooting
If you encounter issues with your transceiver, refer to the table below for possible causes and solutions. If problems persist, contact your distributor, dealer, or service center.
| Problem | Possible Cause / Solution |
|---|---|
| The radio does not start. | The battery is low, replace with a charged battery or proceed to charge. Ensure the battery is installed correctly. |
| The battery runs down quickly. | The battery life has ended, replace with a new one. Ensure the battery is fully charged. |
| The receiving indicator LED lights but no sound from the speaker. | Volume setting is too low. Ensure CTCSS/DCS undertones match those programmed in other radios in your group. |
| When transmitting, other group members do not receive communication. | Ensure CTCSS/DCS undertones match. You or your partner may be too far away or in an area of poor RF signal propagation (e.g., tunnels, mountainous areas, large metal structures). |
| In "standby" mode, the transceiver transmits without pressing the "PTT". | Check if the VOX level adjustment function is set too sensitively. |
| Receiving communications from other user groups while communicating with your group. | Change frequency or channel. Change the CTCSS or DCS undertones in your group. |
| Communication with other members of your group is poor or low quality. | You or your partner is too far away or in an area of poor radio signal propagation, such as inside a tunnel, inside an underground car park, in a mountainous area, including large metal structures, etc. |
14. Specifications
14.1. General
| Frequency range: | 65MHz-108MHz (Commercial FM radio reception only) VHF: 136MHz-174MHz (Rx/Tx) UHF: 400MHz-520MHz (Rx/Tx) |
| Memory channels: | Up to 128 channels |
| Frequency stability: | 2.5ppm |
| Frequency step: | 2.5kHz/5kHz/6.25kHz/10kHz/12.5kHz/20kHz/25kHz |
| Antenna impedance: | 50 Ω |
| Operating temperature: | -20°C to +60°C |
| Supply voltage: | Rechargeable Lithium-Ion 7.4V/1800mAh |
| Consumption in reception: | 380mA |
| Consumption in transmission: | ≤1.4A |
| Mode of operation: | Simplex or semi-duplex |
| Duty cycle: | 03/03/54 min. (Rx / Tx / Standby) |
| Dimensions: | 173mm x 100mm x 95mm (from product properties, PDF says 65mmx41.5mmx133.8mm, using product properties for consistency) |
| Weight: | 279g (approximate) |
14.2. Transmitter
| RF power: | 5W/1W (Note: Product title mentions 10W, but specs say 5W/1W. Please verify.) |
| Type of modulation: | FM |
| Emission class: | 16KF3E/11KF3E (W/N) |
| Maximum deviation: | ≤±5 kHz/≤±2.5 kHz (W/N) |
| Spurious emissions: | <-60 dB |
14.3. Receiver
| Receiver sensitivity: | 0.2 μV (at 12 dB SINAD) |
| Intermodulation: | 60 dB |
| Audio output: | 1W |
| Spurious Radiation: | ≥65dB |
Note: All specifications shown are subject to change without notice.
15. Warranty and Support
The device described in this Certificate is guaranteed for a period of TWO YEARS from the date of sale to the final user. This Warranty Certificate is unique and not transferable and may not be reissued for new or original or copy. Substitution of product failure or any part thereof shall not involve extension of the guarantee.
The warranty covers the replacement and free replacement of all parts that are defective in materials and components used in manufacturing and/or assembly of the apparatus.
The warranty does not cover any faults caused by accident, improper installation and use, electric shock (e.g., storms), connection to a power source other than that specified, reverse polarity in the diet, or claims due to deterioration in the external appearance of normal use, nor the amount or condition of the accessories.
Checking the accessories is the responsibility of the purchaser at the time of purchasing the device.
The warranty does not cover rechargeable batteries even if they are part of the equipment purchased as they are considered consumables; the impairment must be reported within a period of fifteen days from the date of purchase.
The warranty is void under the following assumptions:
- Devices that have been manipulated by another or by anyone other than authorized service provider.
- Equipment and accessories in which the serial number has been altered, deleted or filed unreadable.
- Use of the product other than as intended.
To make use of the guarantee, it is necessary to provide the dealer or any authorized service with the defective device, its accessories, and the following documentation:
- Warranty Certificate duly completed and sealed.
- Original invoice which clearly identifies the device and the date of purchase.
- Description of the faults.
The warranty terms contained in this Certificate of Guarantee do not exclude, modify, or restrict the statutory rights of the buyer by virtue of the laws in force at the time of purchase, but are added to them.
For full warranty details and support, please refer to the official user manual PDF: Baofeng UV-9R EU User Manual (PDF).