Jonsbo ZB-120/240/360

Contents

Jonsbo ZB-120/240/360 ARGB Computer Case Fan User Manual

Models: ZB-120 (Single Fan) / ZB-240 (2-Fan Kit) / ZB-360 (3-Fan Kit with Controller)

Introduction

This manual provides essential information for the safe and effective installation, operation, and maintenance of your Jonsbo ZB-series ARGB computer case fans. These fans feature a unique 4-sides infinity mirror lighting effect and integrated cooling, designed to enhance both the aesthetics and thermal performance of your computer system.

Please read this manual thoroughly before proceeding with installation or use.

Safety Information

WARNING

  • ELECTRICAL HAZARD: Always disconnect the main power from your computer completely and unplug the power cord from the wall outlet before any installation to prevent electric shock.
  • MOVING PARTS HAZARD: Keep hands, loose clothing, and cables clear of fan blades during operation.
  • RGB VOLTAGE WARNING (For ZA-360 Kit): This fan kit uses a 5V Addressable RGB (3-pin) standard. NEVER connect its RGB cable to a traditional 12V RGB (4-pin) header. Incorrect connection will cause permanent failure of the lighting components and may create a safety risk. Ensure voltage compatibility by verifying your motherboard's specifications before connection.
  • DAMAGED PRODUCT: Do not operate the fan if it is physically damaged, makes abnormal noises, or emits smoke. Disconnect power immediately and contact support.
  • SMALL PARTS: Choking hazard. Keep out of reach of young children.

Installation should be performed by individuals with basic PC hardware knowledge. If unsure, consult a professional.

Product Usage Instructions & Restrictions

  • This product is designed exclusively for internal use within standard computer cases.
  • Do not use in environments with high humidity, excessive dust, liquids, or corrosive substances.
  • Do not block the air intake or exhaust vents of the fan.
  • Do not insert any objects into the fan while it is spinning.
  • Do not attempt to disassemble or repair the fan. This voids the warranty.

Setup and Installation

Before beginning installation, ensure your computer is powered off and unplugged from the wall outlet.

  1. Identify Airflow Direction: Locate the directional arrows on the fan frame. These indicate the direction of airflow and blade rotation. Typically, air flows from the front side (with the open frame and supporting struts) to the rear side (with the motor hub and label). The ZB series offers both regular and reverse blade options for flexible airflow management.
  2. Mount the Fan:
    • For Case Mounting: Align the fan with the case's fan mounting holes. Secure it using the provided standard screws.
    • For Radiator/Heatsink Mounting: Use the provided longer screws to attach the fan through the radiator fins.
    • For the ZA-360 3-Fan Kit: You may connect multiple fans together via daisy-chain cables (if included) before mounting them as a unit.
  3. Connect Cables:
    • Power & Speed Control (PWM): Connect the fan's 4-pin PWM connector to a corresponding SYS_FAN or CPU_FAN header on your motherboard. For the ZA-360 kit, you may connect the combined PWM cable from the fans to the included controller or directly to a motherboard header.
    • RGB Lighting (ZA-360 Kit ONLY): Connect the 3-pin 5V Addressable RGB (ARGB) cable to a compatible 5V ADD_RGB header on your motherboard OR to the included RGB controller. Ensure voltage compatibility (5V ARGB only).
    • Controller Power (ZA-360 Kit): If using the included controller, connect its SATA power cable to a SATA power connector from your power supply.
  4. Final Check & Power On: Ensure all connections are secure and cables are routed away from fan blades and other components. Reconnect the main power and start your system.
Jonsbo ZB-series fans with ARGB lighting and size comparison, showing regular and reverse blade types.

Figure 1: Jonsbo ZB-series fans with ARGB lighting and size comparison, showing regular and reverse blade types.

Diagram illustrating wind direction for regular and reverse fan blades.

Figure 2: Diagram illustrating wind direction for regular and reverse fan blades.

Diagram showing simplified wiring with one line connection to the motherboard for seamless connectivity.

Figure 3: Simplified wiring with one line connection to the motherboard for seamless connectivity.

Operating Instructions

After successful installation and power-on, you can control your Jonsbo ZB-series fans:

  • Fan Speed Control: Use your motherboard's BIOS/UEFI settings or dedicated fan control software (if provided by your motherboard manufacturer) to adjust the PWM fan speeds.
  • ARGB Lighting Control:
    • If connected to a motherboard's 5V ARGB header, use the motherboard's RGB software (e.g., ASUS Aura Sync, MSI Mystic Light Sync, Gigabyte RGB Fusion, ASRock Polychrome Sync) to customize lighting effects.
    • If using the included RGB controller (for ZA-360 kit), refer to the controller's specific instructions for adjusting lighting modes and colors.
Diagram showing ARGB colorful synchronous light effect, connecting to motherboard or controller via 3-pin 5V optical control interface.

Figure 4: ARGB colorful synchronous light effect connection diagram.

Maintenance

Regular maintenance helps ensure optimal performance and longevity of your fans:

  • Cleaning: Periodically clean dust from the fan blades and frame using compressed air or a soft, dry cloth. Ensure the computer is powered off and unplugged before cleaning.
  • Inspection: Check cables for any signs of wear or damage. Ensure all connections remain secure.
  • Avoid Lubrication: The fans use hydraulic bearings which are sealed and do not require external lubrication. Attempting to lubricate them may cause damage.

Troubleshooting

If you encounter issues with your Jonsbo ZB-series fans, consider the following:

  • Fan Not Spinning:
    • Check if the 4-pin PWM connector is securely plugged into the motherboard header.
    • Ensure the computer is receiving power.
    • Verify fan speed settings in BIOS/UEFI or software are not set to 0 RPM.
  • RGB Lighting Not Working:
    • Ensure the 3-pin 5V ARGB connector is securely plugged into a compatible 5V ARGB header on the motherboard or the controller.
    • CRITICAL: Confirm it is a 5V ARGB header, not a 12V RGB header. Connecting to a 12V header will damage the LEDs.
    • If using a controller, ensure the controller is receiving SATA power.
    • Check motherboard RGB software settings.
    • For ZA/ZB-360 fans, ensure your motherboard or controller supports at least 68 LED chips.
  • Abnormal Noise or Vibration:
    • Ensure no cables or other components are touching the fan blades.
    • Check if the fan is securely mounted and screws are tightened.
    • Clean any dust buildup on the fan blades.

Specifications

The Jonsbo ZB-series fans are available in different sizes and configurations. Please refer to the table below for detailed specifications. Note that 'Regular' and 'Reverse' versions primarily differ in blade orientation for airflow direction.

Image showing multiple versions of Jonsbo ZB-series fans: ZB-360W (Regular), ZB-360WR (Reverse), ZB-240W (Regular), ZB-240WR (Reverse), ZB-120W (Regular), ZB-120WR (Reverse).

Figure 5: Multiple versions of Jonsbo ZB-series fans.

Detailed specification parameters table for Jonsbo ZB-120, ZB-240, and ZB-360 fans, including fan size, rotational speed, airflow, wind pressure, noise, rated voltage, current, power, bearings, lifespan, interface, and number of LED beads.

Figure 6: Detailed Specification Parameters for ZB-120, ZB-240, and ZB-360.

Jonsbo ZB-Series Fan Specifications
Parameter ZB-120 (Regular) ZB-120R (Reverse) ZB-240 (Regular) ZB-240R (Reverse) ZB-360 (Regular) ZB-360R (Reverse)
Fan Size 120(L)×120(W)×28mm(H) 120(L)×120(W)×28mm(H) 242(L)×123(W)×28mm(H) 242(L)×123(W)×28mm(H) 362(L)×123(W)×28mm(H) 362(L)×123(W)×28mm(H)
Fan Rotational Speed 700-2400 (±10%) RPM 700-1800 (±10%) RPM 700-2400 (±10%) RPM 700-1800 (±10%) RPM 700-2400 (±10%) RPM 700-1800 (±10%) RPM
Fan Air Volume 20.95-65.26 CFM 18.75-47.71 CFM 20.95-65.26 CFM 18.75-47.71 CFM 20.95-65.26 CFM 18.75-47.71 CFM
Wind Pressure 0.45-3.20 mmH2O 0.33-1.66 mmH2O 0.45-3.20 mmH2O 0.33-1.66 mmH2O 0.45-3.20 mmH2O 0.33-1.66 mmH2O
Noise 20.3-36.6 dB(A) 16.4-30.7 dB(A) 20.3-36.6 dB(A) 16.4-30.7 dB(A) 20.3-36.6 dB(A) 16.4-30.7 dB(A)
Rated Voltage (FAN) 12V 12V 12V 12V 12V 12V
Rated Voltage (LED) 5V 5V 5V 5V 5V 5V
Rated Current (FAN) 0.20A 0.10A 0.37A 0.16A 0.55A 0.35A
Rated Current (LED) 0.71A 0.71A 1.16A 1.16A 1.35A 1.35A
Power Consumption (FAN) 2.40W 1.20W 4.44W 1.92W 6.60W 4.20W
Power Consumption (LED) 3.55W 3.55W 5.80W 5.80W 6.75W 6.75W
Fan Bearings Hydraulic Bearings
Life Span ≥20000h Room Temp: 25 ℃
Interface PWM 4PIN, ARGB 3PIN
Number of LED beads 32 around + 9 parallel axis 32 around + 9 parallel axis 52 around + 18 parallel axis 52 around + 18 parallel axis 68 around + 27 parallel axis 68 around + 27 parallel axis

*Note: For ZA/ZB-360 fans, please select a motherboard or controller that supports the corresponding number and specifications of LED chips (68 or more).

Chart comparing noise, rotational speed, and air volume for regular and reverse fan blades.

Figure 7: Quiet/Low Noise PWM ARGB Fan performance comparison.

User Tips

  • Optimal Airflow: Plan your fan placement carefully, considering both intake and exhaust to create an effective airflow path within your PC case. Using a mix of regular and reverse blade fans can help achieve desired airflow patterns without showing the less aesthetic side of the fan.
  • Cable Management: Take time to route cables neatly. This not only improves aesthetics but also prevents interference with moving parts and improves airflow.
  • ARGB Compatibility: Always double-check your motherboard's manual for ARGB header voltage (must be 5V, 3-pin) and maximum LED chip support to ensure full functionality and prevent damage.

Compliance Markings

This product bears the CE mark, indicating conformity with applicable European Union directives. It complies with the essential requirements of the relevant European Union Directives and harmonized standards, including:

  • Directive 2014/35/EU (Low Voltage Directive)
  • Directive 2014/30/EU (Electromagnetic Compatibility Directive)
  • Directive 2011/65/EU & Delegated Directive (EU) 2015/863 (Restriction of Hazardous Substances - RoHS)
  • Harmonized Standard: EN 62368-1:2014 + A11:2017 (Audio/video, information and communication technology equipment - Safety requirements)

Warranty and Support

For technical support and warranty service, please visit the official JONSBO website or contact your authorized retailer. Keep your proof of purchase for warranty claims.

A user manual in PDF format is also available for download from the product page or the manufacturer's website.

© 2024 Jonsbo. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.