LEEOCAR Android Touch Screen Car Radio

Contents

LEEOCAR Android Touch Screen Car Radio User Manual

For Chevrolet Silverado & GMC Sierra 2014-2018

Model: Android Touch Screen Car Radio

1. Introduction

This manual provides detailed instructions for the installation, operation, and troubleshooting of your LEEOCAR Android Touch Screen Car Radio. Please read this manual thoroughly before installation and use to ensure proper functionality and safety.

1.1. Compatibility

This car stereo is designed for Chevrolet Silverado and GMC Sierra models from 2014 to 2018. It features a 10.1-inch 2.5D capacitive touch screen with Android 12, built-in GPS, WiFi, Bluetooth, and support for Wireless/Wired Apple CarPlay and Android Auto.

Compatibility chart for Chevrolet Silverado and GMC Sierra 2014-2018 dashboards, showing various OEM screen types and indicating 'Fit' or 'Not Fit' for the new unit.

Figure 1: Dashboard compatibility for Chevrolet Silverado & GMC Sierra 2014-2018. Please verify your vehicle's dashboard matches a 'Fit' configuration.

1.2. Important Compatibility Note

This unit is NOT suitable for car models equipped with a BOSE AMP system. If your car has a Bose AMP, please do not proceed with installation. If you are unsure, please contact customer support.

Image showing a car's speaker mesh with 'BOSE' logo, indicating incompatibility with the car stereo unit.

Figure 2: Example of a BOSE speaker mesh. If your vehicle has this, the unit is not compatible.

2. Package Contents

Please check the contents of your package against the list below. If any items are missing, contact customer service immediately.

Diagram showing all included accessories: SWC Line, RCA Cable, Original USB Cable, Microphone, Radio antenna, Crowbar, Power Cable, USB Cable, GPS Antenna, Small speaker, Canbus, Camera Input, Camera, and the main unit.

Figure 3: Package contents diagram.

  • 1 x Car MP5 Player (Main Unit)
  • 1 x Power Cable
  • 1 x GPS Antenna
  • 1 x Camera
  • 1 x Rear Camera Input Cable
  • 1 x RCA Cable
  • 1 x Canbus Box
  • 2 x USB Cables (one 6-pin, one 4-pin)
  • 1 x Original USB Cable
  • 1 x Radio Antenna
  • 1 x SWC Cable
  • 1 x Microphone
  • 1 x Small Speaker
  • 1 x Crowbar
  • 1 x Instruction Manual (this document)

3. Setup and Installation

3.1. General Installation Warning

Do not connect wiring while power is on. Doing so may result in system errors, fuse damage, or permanent malfunction. Always disconnect the vehicle's battery before beginning installation.

Professional installation is highly recommended. If you are unsure about any steps, please consult a qualified technician.

3.2. RPO Codes Determination Methods

To ensure proper fit and wiring, it is important to determine your vehicle's RPO (Regular Production Option) codes. These codes indicate specific features and configurations of your vehicle.

  1. Determined by the original vehicle dashboard: Observe the size of your original vehicle's screen. Common RPO codes correspond to specific screen sizes: 103/104 for 4.2-inch, IOB for 7-inch, and 105/106 for 8-inch screens.
  2. Determined by the front passenger glove box: Open the passenger side glove box. Inside, you should find two silver labels. The RPO code can typically be found on the left label.

3.3. Radio Wiring Diagram

Refer to the following diagram for the main wiring connections. Ensure all cables are securely connected to their corresponding ports.

Detailed wiring diagram showing connections for RCA line, USB cables, Reversing line, Radio adapter cable, Canbus, Protocol serial line, GPS cable, and power cable.

Figure 4: Main Radio Wiring Diagram.

3.4. Radio Rear Panel Pinout Diagram

The following table details the pin assignments for the RCA cable connections on the radio's rear panel.

RCA Cable Pinout (8 Core Radio)
Pin Function
IVIDEO_OUT (Non-functional)
IICVBS-IN-1
IIIAUX_IN L
IVAUX_IN R
VSUB
VIAUDIO_OUT R
VIIAUDIO_OUT L
VIIIMic Cable

3.5. Rear Camera Wiring Tutorial

Follow these steps to connect the rear camera:

  1. Connect the red cable (1) to the backup light's positive (+) terminal.
  2. Connect the black cable (2) to the backup light's negative (-) terminal.
  3. Connect the reversing detection cable (labeled 'G5' in the diagram) to the white cable (3) which extends from the video input cable.
Diagram showing how to connect the rear camera: red cable to backup light +, black cable to backup light -, and reversing detection cable to the white video input cable.

Figure 5: Rear Camera Wiring Diagram.

Please Note:

The unit's Bluetooth & WiFi antenna and the Reverse Camera RCA are bundled together. Whether you install a reversing camera or not, please insert the Camera RCA into the 10-pin port.

3.6. Steering Wheel Controls Setup Tutorial

To configure your steering wheel controls, navigate to the settings menu on the unit:

  • Go to Settings > Factory (enter password "3368") > Car Model.
  • Select XP(Simple)--GM/Chevrolet--Silverado--2014-2018.Auto.

For vehicles with RPO code IOB, use the XC-1255 harness. For RPO codes 103/104/105/106, use the XC-1256 harness.

Select the appropriate steering wheel control adapter cable based on the connector shape of your original steering wheel control system.

Installation Location: Connect the 10-pin connector located under the steering wheel.

Diagram illustrating Steering Wheel Control (SWC) setup, showing how to program buttons and the location of the 10-pin connector under the steering wheel.

Figure 6: Steering Wheel Control Setup and Connector Location.

3.7. HMI Module Location (for 104/105/106)

For vehicles with RPO codes 104/105/106, the HMI module is used for adapting the factory vehicle USB and original rear camera. To locate it:

  1. Remove the front passenger armrest box.
  2. Remove the screws at the six indicated positions.
  3. Locate the HMI module behind the metal pipe.

Only connect the labeled plugs on the original car radio. The remaining plugs do not need to be connected.

4. Operating Instructions

4.1. Basic Operation

The unit features a 10.1-inch 2.5D capacitive touch screen for intuitive control. Physical buttons are also available for quick access to common functions:

  • Reset: Resets the unit.
  • Power: Turns the unit on/off.
  • Menu: Accesses the main menu or specific app menus.
  • Back: Navigates back in menus or applications.
  • Vol+ / Vol-: Adjusts the volume up or down.
Product display diagram showing the dimensions of the 10.1-inch screen unit and labeling the physical buttons: Reset, Power, Menu, Back, Vol+, Vol-.

Figure 7: Product Display and Physical Buttons.

4.2. Wireless & Wired Apple CarPlay / Android Auto

The unit supports both wireless and wired connections for Apple CarPlay and Android Auto, integrating your smartphone's features with the car stereo.

  • Wireless Connection: Connect via Bluetooth. This allows for voice-controlled navigation, calls, messages, and music playback. (iPhone for CarPlay, Android phone for Android Auto - requires Android Auto app).
  • Wired Connection: Connect via USB.
Diagram illustrating Wireless Apple CarPlay and Android Auto/Mirror Link features, showing Bluetooth and USB connection options for various apps.

Figure 8: Apple CarPlay & Android Auto/Mirror Link Functionality.

4.3. GPS Navigation

The unit comes with built-in GPS navigation. You can use offline maps (data download required via internet) or online maps like Google Maps when connected to WiFi.

Features diagram for Built-in GPS Navigation with a map interface example.

Figure 9: Built-in GPS Navigation.

4.4. WiFi Connectivity

Connect the unit to a WiFi network to access online maps, stream music, browse the internet, and download applications from the Play Store.

Features diagram for WiFi connectivity, showing various social media and streaming apps.

Figure 10: WiFi Connectivity.

4.5. Bluetooth

The unit features Bluetooth 5.0 for hands-free calls, Bluetooth music streaming (A2DP), and automatic phonebook loading.

Bluetooth Keyword: 0000

Features diagram for Bluetooth, showing disconnected, paired, and available devices.

Figure 11: Bluetooth Interface.

4.6. FM/RDS Radio

Enjoy FM radio with RDS (Radio Data System) functionality. The unit supports 18 preset stations.

Features diagram for FM/RDS Radio, showing frequency tuning and preset stations.

Figure 12: FM/RDS Radio Interface.

4.7. Rear Camera

The unit supports AHD high-definition 1080P camera image input for reversing. Ensure the camera is wired correctly as per Section 3.5.

Features diagram for AHD Backup Camera, showing 1080P Full HD, Night Vision, Waterproof, and Wide-angle capabilities.

Figure 13: AHD Backup Camera Features.

4.8. Media Playback

The unit supports various digital media formats including MP4, Mp3, WMA, JPEG. It features double USB adapter inputs for connecting external storage devices.

5. Maintenance

To ensure the longevity and optimal performance of your car stereo, follow these maintenance guidelines:

  • Screen Cleaning: Use a soft, lint-free cloth to gently wipe the touch screen. For stubborn smudges, slightly dampen the cloth with water or a screen-safe cleaner. Avoid harsh chemicals or abrasive materials.
  • Dust Removal: Regularly clean dust from the unit's vents and openings using a soft brush or compressed air.
  • Software Updates: Periodically check for software updates to ensure you have the latest features and bug fixes. These can usually be found in the system settings or on the manufacturer's website.
  • Avoid Extreme Temperatures: Do not expose the unit to extreme heat or cold for prolonged periods, as this can affect its electronic components. The recommended operating temperature is -20℃ to 70℃.

6. Troubleshooting (FAQs)

This section addresses common issues and provides solutions.

Q1: What is the factory password?

A: The factory password is 3368.

Q2: What should I do if the radio experiences issues like freezing and stuttering?

A: Go to Settings > User > Backup and Reset (enter "3368") > Erase All Data (Factory Reset). You can also perform a hard reset by using a pin-like tool to press the RST hole on the front panel of the radio for 5-10 seconds.

Q3: Is it possible to support Sirius XM radio?

A: The radio does not have a port for connecting a SiriusXM tuner for Satellite Radio. You may check the radio's Play Store for an online SiriusXM Radio app, but compatibility with third-party apps cannot be guaranteed.

Q4: Does it support the original car microphone?

A: The factory microphone cannot be retained. Connect the external microphone (included) to the 3.5mm port on the RCA cable. It is recommended to install the microphone on the driver's side sun visor, with the microphone head facing the driver's face.

Q5: Can I use a voice assistant (Siri, etc.)?

A: The voice assistant can only be activated through your phone. Connect your phone to the radio via Bluetooth, Android Auto, or CarPlay, and then use the voice assistant feature on your phone.

Q6: Why is the time not accurate?

A: Ensure your GPS antenna is properly connected. Install the GPS antenna on the A-pillar of your car or just outside the dash (it will not work if installed inside the dash). Then, connect your radio to Wi-Fi or a hotspot, go to Settings > System > Date and Time, and enable "Use network-provided time" and "Use network-provided time zone."

Q7: Why is the WiFi connection unstable?

A: Verify that the single yellow RCA camera port is properly connected to the radio, as the adjacent small wires are intended for receiving Wi-Fi and Bluetooth signals. Note that Bluetooth and WiFi cannot be used at the same time.

A: Go to Settings > Factory (enter "3368") > Boot Screen Logo to change the logo. To save different logo images, create a folder named 'mycar' in the root directory of your USB drive. Download the desired image (1280x800 resolution, in .bmp format), then connect the USB drive to the radio using the supplied USB cable. The image will then be available for selection in the "Boot Screen Logo" setting.

Q9: Why is there no sound from the radio after installation?

A: If your vehicle is equipped with a Bose audio system, an additional audio adapter (fiber optic box) is required. Connect the included MST cable to the adapter and the factory CD player to ensure proper audio output. For vehicles without a Bose sound system, the audio adapter (fiber optic box) and MST cable are not needed.

Q10: Why is the steering wheel control not working after installing the radio?

A: If you are using the XC-1256 wiring harness, follow these steps:

  • Check all physical connections: Ensure the correct steering wheel control adapter cable is selected and securely connected to the 10-pin connector under the steering wheel. Confirm that the 8-pin plug on the power cable is correctly inserted into the 8-pin port on the back of the radio unit.
  • Configure the correct car model in settings: Go to Settings > Factory (enter password "3368") > Car Model, then select "XP(Simple)--GM/Chevrolet--ALL--XP(H)".

Q11: How should I install to retain the factory rear camera?

A: If you are using the XC-1255 harness and your vehicle is a 2018 model with an RPO code: IOB, a short-circuit procedure is required on the gray connector behind the factory display. This reroutes the camera signal to your new radio. Use the provided jumper wires to make the following connections on the factory gray connector:

  • Jumper wire1: Connect Pin 5 to Pin 7.
  • Jumper wire2: Connect Pin 6 to Pin 8.

This completes the necessary circuit for the camera signal to bypass the factory system.

Q12: The rear camera image is reversed (left to right). How can I fix it?

A: Go to Settings > General and toggle the "Mirror view on reverse image" option to adjust.

Q13: Why is the original car's rear camera image not clear?

A: The factory rear camera image may not be clear enough because the old camera signal uses CVBS (360P), while our new radio screen supports AHD (1080P). It is recommended to use the supplied camera for better image quality on the new radio.

Q14: How do I turn off the camera's guideline?

A: Go to Settings > Factory (enter "3368") > Original Car Agreement and turn off "Reverse Parking Line."

7. Specifications

Feature Specification
SystemAndroid 12
Screen Size10.1 inches
Screen Resolution1280*800
RAM4GB (Available options: 2GB)
ROM (Internal Storage)64GB (Available options: 32GB)
CPU4 cores
Bluetooth Version5.0
Power Output4*45W
VoltageDC 12V
Work Temperature-20℃ to 70℃
Apple CarPlaySupport Wireless/Wired Connection
Android AutoSupport Wireless/Wired Connection
WiFiSupport
GPSSupport (Built-in offline maps, internet for data download)
Steering Wheel ControlSupport
Camera InputAHD/CVBS Reversing Input
Video OutputSupport
USBDouble USB interface
Radio BandFM/RDS
Digital Media FormatMP4, Mp3, WMA, JPEG
OSD LanguageChinese (Simplified), Chinese (Traditional), Albanian, Arabic, Azeri, Irish, Estonian, Belarusian, Bulgarian, Icelandic, Polish, Persian, Boolean text (Dutch South Africa), Danish, German, Russian, French, Filipino, Finnish, Georgian, Haitian Creole, Korean, Dutch, Galicia, Catalan, Czech, Croatian, Latin, Latvian, Lithuanian, Romanian, Maltese, Malay, Macedonian, Norwegian, Portuguese, Japanese, Swedish, Serbian, Slovak, Slovenian, Swahili, Thai, Turkish, Welsh, Ukrainian, Hebrew, Greek, Spain's Basque, Spanish, Hungarian, Armenian, Italian, Yiddish, Hindi, Urdu India, Indonesia, English, Vietnamese
Item Weight2.5kg
MaterialComposite Material
CertificationCE, FCC, WEEE, EAC, RoHS, KC

8. User Tips

  • For optimal GPS performance and accurate time synchronization, ensure the GPS antenna is installed in a clear line of sight, such as on the A-pillar or just outside the dash. Avoid installing it inside the dash.
  • If you experience any freezing or stuttering, a factory reset (Settings > User > Backup and Reset > Erase All Data) or a hard reset (pressing the RST hole with a pin for 5-10 seconds) can often resolve the issue.
  • When connecting to WiFi, ensure the yellow RCA camera port is properly connected, as its adjacent wires are crucial for stable WiFi and Bluetooth signals. Remember that Bluetooth and WiFi cannot be used simultaneously.
  • If your original car camera image appears unclear, it's likely due to the old CVBS (360P) signal not matching the new unit's AHD (1080P) display. Using the provided AHD camera is recommended for the best image quality.

9. Warranty and Support

9.1. Warranty

This product comes with a 1-year warranty. Please retain your proof of purchase for warranty claims.

9.2. Technical Support

For technical assistance, missing accessories, or further inquiries, please contact our customer service team. You can also visit our official website for after-sales support and a forum to ask questions or report issues.

QR code to access the Function Manual and technical support website.

Figure 14: Scan this QR code to access the Function Manual and technical support resources.

A detailed user manual in PDF format is available for download. Refer to the 'Item guides & documents' section on the product page for the link.

10. Product Overview Video

Watch this video for a visual overview of the car stereo unit.

Video 1: Product demonstration showing the car stereo unit from various angles.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.