1. Introduction
Thank you for choosing the Tuya ZigBee + RF433 Smart Wall Switch. This device integrates seamlessly into your smart home ecosystem, offering convenient control of your lighting through mobile apps, voice commands, and traditional touch. Please read this manual carefully before installation and use to ensure safe and optimal performance.
2. What's in the Box
- Tuya ZigBee + RF433 Smart Wall Switch
- User Manual
- Mounting Screws
3. Safety Information
Risk of Electric Shock:
- Improper operation can cause personal injury and property damage.
- Always ensure the power supply is disconnected at the circuit breaker before any installation or maintenance.
- If you are unsure about any part of these instructions or lack electrical wiring experience, please seek professional help from a qualified electrician.
4. Setup and Installation
4.1 Pre-installation Checklist
- Power Off: Make sure that the power supply on the circuit breaker is turned off before wiring.
- Neutral Wire Required: This switch requires a neutral wire for operation. Confirm that your wall box contains a neutral wire (usually white). If your wall box does not have a neutral wire, consider installing the switch at another location or consult a professional electrician.
- Wire Colors: The wire colors indicated in this manual are common, but may differ in your home's wiring.
- Secure Connections: Ensure that all wire conductors are firmly fixed on each terminal.
- Wi-Fi Signal: Before wiring, ensure that your Wi-Fi signal is stable and works normally in the installation area.
- Zigbee Gateway: This switch requires a Tuya Zigbee gateway for smart functionality. Ensure your gateway is set up and ready.
4.2 Installation Steps
- Prepare for Installation:
- Close the circuit breaker to cut off power to the switch location.
- Use an electrical tester to confirm that the power supply is off.
- Ensure the switch is in the 'OFF' position before wiring.
- Remove Existing Switch:
- Carefully remove the existing wall plate and switch.
- Use an electrical tester to identify and mark the line (live) wire and other wires.
- Disconnect the power supply wires and remove the old switch.
- Wiring the Smart Switch: Connect the wires from your wall box to the smart switch terminals according to the wiring diagrams below.
4.3 Wiring Diagrams
Important: Always ensure power is off at the circuit breaker before handling any wiring.

Figure 1: Two common wiring methods. Left: Neutral & Live Wire (Neutral Wire Required). Right: Single Live Wire (No Neutral Wire Required, requires a capacitance module, not included).
Standard Wiring (Neutral & Live Wire Required):
- Connect the Live wire (L) from your home wiring to the 'L' terminal on the switch.
- Connect the Neutral wire (N) from your home wiring to the 'N' terminal on the switch.
- Connect the Lighting wire(s) (to your light fixture) to the corresponding output terminal(s):
- For 1-Gang switch: Connect to 'L1' terminal.
- For 2-Gang switch: Connect to 'L1' and 'L2' terminals.
- For 3-Gang switch: Connect to 'L1', 'L2', and 'L3' terminals.

Figure 2: Detailed wiring diagrams for 1-Gang, 2-Gang, and 3-Gang switches (from user manual).
4.4 Mounting the Switch
- Carefully place the wired switch into the wall box.
- Use the provided mounting screws to secure the switch to the wall box.
- Clip the glass wall panel onto the switch module until it clicks into place.
4.5 Power On and Initial Test
- Turn on the power again at the circuit breaker.
- Test the switch by touching the panel to ensure the lights turn on and off manually.
4.6 App Installation and Pairing
This switch works with the 'Smart Life' or 'Tuya Smart' application.
- Download App: Download and install the 'Smart Life' or 'Tuya Smart' app from your mobile app store (iOS or Android). You can also scan the QR code provided in the original user manual.
- Add Zigbee Gateway: Before adding the smart switch, ensure your Tuya Zigbee gateway is already set up and added to the app.
- Enter Pairing Mode:
- Ensure the smart switch is connected to power according to the wiring diagram.
- Press and hold the switch button for approximately 5-10 seconds until the indicator light on the switch starts flashing rapidly. This indicates it's in configuration mode. The indicator light will go out once configuration is successful.
- Add Device in App:
- Open the 'Smart Life' or 'Tuya Smart' app.
- Navigate to your Zigbee gateway in the app.
- Select 'Add Sub Device' or 'Add Device'.
- The app will search for nearby devices. Select 'Zigbee Switch' from the list of found devices.
- Follow the on-screen prompts to complete the addition process.
- Network Environment: Pay attention to your network environment. Only a 2.4GHz Wi-Fi network can be used for pairing; 5GHz networks are not supported.
5. Operating Instructions
5.1 Manual Control
Touch the glass panel of the switch to manually turn your lights on or off.
5.2 App Remote Control

Figure 3: Control the switch anytime, anywhere via the mobile app.
Once paired, you can control your lights remotely from anywhere using the 'Smart Life' or 'Tuya Smart' app on your smartphone or tablet. You can turn lights on/off, check their status, and manage settings.
5.3 Voice Control

Figure 4: Seamless compatibility with Alexa, Google Home, SmartThings, and Alice for voice control.
The switch is compatible with popular voice assistants like Amazon Alexa, Google Assistant, SmartThings, and Alice. Link your 'Smart Life' or 'Tuya Smart' account to your voice assistant app and use voice commands to control your lights (e.g., "Alexa, turn on the living room light").
5.4 Timer Switch & Countdown Timer

Figure 5: Customize daily on/off times to match your lifestyle.
Set schedules and countdown timers within the app to automatically turn lights on or off at specific times, enhancing convenience and energy efficiency.
5.5 RF433 Local Control

Figure 6: Control your switch using RF433 wireless remotes, even offline.
In addition to Zigbee, the switch supports RF433 wireless protocol. This allows for local control using compatible RF433 remote controllers, providing an alternative control method that works even if your Wi-Fi network is down.
5.6 Shared Control for Family Members

Figure 7: Share control of the switch with your family through the Smart Life App.
You can share control of the smart switch with other family members through the 'Smart Life' or 'Tuya Smart' app, allowing everyone in the household to manage the lights.
5.7 Reboot Memory Function

Figure 8: Configure the switch to remember its last status after a power outage.
The switch features a reboot memory function. In the app settings, you can choose how the switch behaves after a power outage: remain OFF, turn ON, or remember its last status before the power interruption.
5.8 Backlight Control
You can turn the backlight of the switch on or off via the app settings, which is useful for bedrooms or to save minimal power.
5.9 Zigbee Signal Repeater Function

Figure 9: The switch can extend your Zigbee network by acting as a signal repeater.
The smart switch can also function as a Zigbee signal repeater, helping to extend the range and stability of your Zigbee network by transmitting signals between your Zigbee gateway and other Zigbee devices (like sensors).
6. Maintenance
6.1 Cleaning

Figure 10: The ultra-clear tempered glass panel is easy to clean and maintains a lasting shine.
The switch features an ultra-clear tempered glass panel. To clean, gently wipe the surface with a soft, damp cloth. Avoid using abrasive cleaners or harsh chemicals that could damage the finish.
6.2 General Care
- Keep the switch dry and away from excessive moisture.
- Avoid exposing the switch to extreme temperatures.
- Do not attempt to disassemble or repair the switch yourself, as this may void the warranty and pose a safety risk.
7. Troubleshooting
- Switch Not Responding:
- Check if the circuit breaker is on.
- Verify all wiring connections are secure and correct (Live, Neutral, Load).
- Ensure the light bulb is working.
- Cannot Pair with App:
- Ensure the switch is in pairing mode (indicator light flashing rapidly).
- Confirm your Zigbee gateway is online and properly configured in the app.
- Make sure your Wi-Fi network is 2.4GHz, as 5GHz is not supported for pairing.
- Bring the switch closer to the Zigbee gateway during pairing.
- Reset the switch by turning off the power at the circuit breaker for 10 seconds, then turning it back on and attempting pairing again.
- Voice Control Not Working:
- Ensure your 'Smart Life' or 'Tuya Smart' account is correctly linked to your voice assistant (Alexa, Google Assistant).
- Check your internet connection.
- Verify the device name in the app matches the name you are using in voice commands.
- RF433 Remote Not Working:
- Ensure the RF433 remote is paired with the switch according to its own instructions.
- Check the battery in the RF433 remote.
8. Specifications

Figure 11: Detailed product parameter information.
| Feature | Specification |
|---|---|
| Wireless Standard | Zigbee 3.0 |
| Working Voltage | AC 100-250V, 50/60Hz |
| Max Load Power | INC-500W / WLED-200W per gang (Total 1000W/Gang from manual) |
| Max Load Current | 10A |
| Power Consumption | ≤ 0.5W |
| Working Temperature | 0°C ~ 40°C |
| RF Frequency | 433.92MHz |
| Wi-Fi Standard | IEEE 802.11 b/g/n 2.4GHz |
| Support App | Tuya Smart & Smart Life APP |
| Voice Control | Google Home, Amazon Alexa, Yandex Alice |
| Network Security | WPA/WPA2 |
| Hub Requirement | Tuya Zigbee Gateway Required |
| Control Mode | APP / RF / Manual / Speaker Voice Control |
| Dimensions | 86mm x 86mm x 36mm (Panel: 9mm, Depth: 36mm) |
| EU LVD Voltage | High voltage: Above 50Vac or 75Vdc |
| Certification | CE, RoHS |
9. Warranty and Support
For any issues, questions, or support needs regarding your Tuya ZigBee + RF433 Smart Wall Switch, please contact the seller or manufacturer directly. Refer to your purchase documentation for specific warranty terms and contact information.