Introduction
Thank you for choosing the Casubaris Airbrush Kit with Compressor. This professional-grade kit is designed for a wide range of applications, from delicate nail art to large-area car painting. It features a dual-action airbrush for precise control, a compressor with 5 adjustable pressure levels, and dual air outlets for enhanced efficiency. Please read this manual carefully before use to ensure safe and optimal operation, and keep it for future reference.
Demonstration of the Airbrush Kit with Compressor (Model TM300-318) showing setup, pressure adjustment, and painting.
The complete Casubaris Airbrush Kit, including the compressor, dual-action airbrush gun, air hose, power adapter, and various accessories.
Electrical Safety Warnings
- Do not expose the compressor to rain or wet conditions. Water entering the compressor will increase the risk of electric shock.
- Do not abuse the cord. Never use the cord for unplugging the compressor.
- Keep the cord away from heat, oil, sharp edges, or moving parts. Damaged or entangled cords increase the risk of electric shock.
Key Parts Diagram
An exploded diagram illustrating the components of the dual-action airbrush, including the 0.3mm nozzle, 7cc gravity feeding cup, dual-action switch, 1/8 hose connector, and tail handle adjusting screw.
Compressor Components:
- Air hose interface
- Power switch
- Pressure adjustment knob
- Compressor Holder
- Battery (internal)
- Type-C charging port
Airbrush Gun Components:
- 0.3mm Nozzle
- 7cc Gravity Feeding Cup
- Dual Action Switch (trigger)
- Adjusting Screw (for paint flow)
- Tail Handle Adjusting Screw
- G1/8 Hose Connector
Setup Instructions
Follow these steps to set up your airbrush kit:
- Connect the power adapter to the compressor.
- Attach one end of the 1.8m braided air hose to the air outlet on the compressor.
- Connect the other end of the air hose to the airbrush gun.
- Fill the airbrush color cup with your desired paint or liquid.
- Turn on the compressor using the power switch.
- Inspect all air connections for leaks. If leaks are found, turn off and unplug the compressor, then repair the leaks before resuming.
A visual guide detailing the six easy steps to set up and begin using your airbrush kit, from connecting components to adjusting pressure and spraying.
Installing the Airbrush Holder
The compressor includes built-in airbrush holders. To install, simply press them into the designated slots on the compressor unit. This partition serves two purposes: it secures the air pump in place while also providing thermal insulation.
Illustration for installing the airbrush holder onto the compressor unit.
Battery Installation/Removal
To install or remove the battery, press firmly on the battery compartment cover as indicated.
Instructions for installing and removing the battery by pressing the designated area.
Shoulder Strap Installation (Optional)
For portability, you can attach the air pump to a shoulder strap:
- First, attach the shoulder strap to your back as shown in the diagram.
- Then, mount the air pump onto the shoulder strap as illustrated.
- To prevent the air pump from falling off during use, secure it with Velcro.
Step 1: Attach the shoulder strap to your back as shown.
Step 2: Mount the air pump onto the shoulder strap as illustrated.
Step 3: Secure the air pump with Velcro to prevent it from falling off during use.
Operating Instructions
Dual-Action Airbrush Control
The dual-action airbrush provides precise control over both air and paint flow:
- Press down the trigger to release air.
- Pull back the trigger to adjust the paint volume.
This allows for fine lines (0.3mm nozzle) to broad, even sprays without streaks or clogs, making your work more professional.
This diagram explains the precise control offered by the double-action airbrush, where pressing the trigger controls air and pulling it back controls paint flow.
Adjustable Pressure Levels
The compressor offers 5 adjustable pressure levels (25, 32, 40, 48, 55 PSI) to suit various projects. Use the '+' and '-' buttons on the compressor to cycle through the pressure settings. The LED indicators will show the current PSI level.
This diagram illustrates the five adjustable pressure levels (25, 32, 40, 48, 55 PSI) and their recommended uses, from delicate nail art to large-area car painting.
The compressor's control panel with PSI indicator lights and buttons for adjusting pressure. The image also shows the dual air outlets, which can be adjusted for single or dual airbrush operation.
Dual Independent Air Outlets
The compressor is equipped with two independent air outlets, allowing you to run two airbrushes simultaneously. This is ideal for multi-color projects or when working with a partner, eliminating the need for frequent tool changes.
- Single Airbrush Mode: Tighten the adjustment screw on the unused outlet to use one airbrush at full pressure.
- Dual Airbrush Mode: Loosen the screw to run two airbrushes simultaneously.
The compressor features two independent air outlets, allowing two airbrushes to be used simultaneously, enhancing efficiency for multi-color projects.
Smart Auto-Stop Compressor
The intelligent pressure sensor automatically stops the motor when the airbrush is not in use, conserving energy, preventing overheating, and extending the unit's lifespan. It restarts instantly as soon as you pick up the airbrush to resume work.
The smart auto-stop compressor automatically pauses when the airbrush is not in use, conserving energy and ensuring safety. It reactivates instantly upon use.
Painting Procedure & Triggering Exercises
- Ensure the workpiece is clean, free of dust, oil, and other impurities. Mask off areas that do not need to be sprayed.
- For small workpieces (e.g., models), hang them or place them on a stand (can be made from ordinary wire hangers, bottles, etc.) to ensure all areas are easily accessible.
- Keep the airbrush nozzle approximately 6 inches (15 cm) away from the workpiece. Use short strokes for spraying and move parallel to the work surface at a steady speed.
- For full coverage, first apply a light coat, wait for it to dry, then apply a second coat. Repeat until the desired coverage is achieved. Do not attempt to achieve full coverage with a single spray pass.
Maintenance
Proper cleaning and maintenance are crucial for the longevity and performance of your airbrush kit.
- Always clean the airbrush immediately after each use, especially when changing colors or finishing a session.
- Wash the inside of the spray pen according to the steps in the manual after use.
- Use the provided cleaning brushes and needles to thoroughly clean the nozzle, needle, and paint cup.
- Do not use thick pigments, as they can clog the nozzle and affect the ejection effect.
- After cleaning, install the spray pen components carefully.
- Store the airbrush compressor in a clean, dry, and safe place, out of reach of children and unauthorized personnel.
- Before each use, inspect the overall condition of the airbrush compressor, including loose hardware, misalignment or jamming of moving parts, cracked or damaged parts, damaged wires, and other conditions that may affect safe operation.
Troubleshooting
If you encounter issues with your airbrush kit, consider the following:
- No Air/Low Pressure: Check all hose connections to ensure they are tight. Verify the compressor is powered on and the pressure level is set correctly. Ensure the dual air outlet screw is adjusted as needed for single or dual airbrush operation.
- No Paint/Poor Spray: Ensure the paint cup is filled and the paint is properly thinned. Check for clogs in the nozzle or needle. Clean the airbrush thoroughly.
- Inconsistent Pressure: While the product is advertised with 5 adjustable PSI levels up to 55 PSI, some users have reported that the actual working pressure might be lower than the maximum advertised. If you experience significantly lower pressure than expected, ensure all connections are secure and the compressor is functioning correctly.
- Airbrush Damage: If the airbrush is dropped, it may affect its performance or cause damage. Handle with care.
- Nozzle/Needle Replacement: Changing the needle and nozzle requires precision. It is recommended that a professional handle these replacements to avoid damage.
Specifications
| Feature | Detail |
|---|---|
| Model Number | TM300-318 |
| Power | 20W 3.7V 8000mAh |
| Working Pressure | 15 PSI |
| Auto Stop Pressure | 28 PSI |
| Motor Pressure | 45-50 PSI |
| Charging Time (5V 2A charger) | Approx. 4-5 hours |
| Charging Time (5V 1A charger) | Approx. 8-10 hours |
| Working Time (Continuous) | 80 minutes (typically exceeds 2 hours with auto-stop) |
| Weight | 35.27 oz (1 kg) |
| Nozzle Diameter | 0.3mm |
| Power Type | Pneumatic |
| Feed Type | Siphon |
| Cup Volume | 7CC |
| Certification | CE, FCC, RoHS |
| Adjustable Pressure Levels | 5 levels (25, 32, 40, 48, 55 PSI) |
| Auto Start/Stop Function | Yes |
| Connector | G1/8 Female |
| Length of Air Hose | 1.8 M (Braided) |
| Dimensions (Compressor) | 18 x 11 x 8 cm |
A screenshot from product specifications confirming the 5 adjustable pressure levels: 25, 32, 40, 48, 55 PSI.
User Tips
- This airbrush kit is generally well-regarded for its performance and ease of use, often noted as being stronger than comparable models.
- While the product advertises up to 55 PSI, some users have observed that the actual working pressure might be closer to 2 kg/cm² (approximately 28 PSI) rather than the stated maximum. Manage expectations regarding the highest pressure output.
- The 0.3mm nozzle is standard, and the compressor is compatible with various G1/8 airbrush pens, allowing for customization.
Warranty & Support
Warranty Information
The TM-60S air compressor is covered by a 90-day limited warranty from the date of purchase against defects in materials and workmanship. Proof of purchase is required.
This warranty is VOID if:
- Damage results from misuse, improper operation, or dropping the unit.
- Unauthorized repairs, modifications, opening, or disassembly occur.
- The unit is not used according to these instructions.
Customer Support
If you encounter any problems during use, please contact our After-Sales Service Department for assistance.
For a detailed user manual in PDF format, please refer to the official document: User Manual (PDF)
Package Contents
Your Casubaris Airbrush Kit includes the following items:
- 1 × Airbrush Gun (0.3mm nozzle)
- 1 × Airbrush Compressor
- 1 × 1.8m Braided Air Hose
- 1 × US Plug Power Adapter
- 2 × Airbrush Holders
- 1 × Wrench
- 1 × Dropper
- 5 × Cleaning Brushes & Needles
- 1 × User Manual (this document)
A visual representation of all components included in the kit: airbrush gun, compressor, pen holder, power adapter, small wrench, dropper, braided air hose, and dust cap.