Introduction
The Coolo Zigbee 3.0 Smart Button is a versatile wireless scene switch designed to enhance your smart home automation. It allows you to trigger various smart scenes with simple physical interactions: single click, double click, and long press. This device requires a Zigbee gateway (hub) for operation and is compatible with eWelink App and Zigbee2MQTT for seamless integration into your smart home ecosystem.
Package Contents
- 1x Coolo Zigbee Smart Button
- 1x User Manual
- 1x Double-sided Sticker
- 1x CR2032 Battery
Setup Instructions
1. Powering On and Battery Installation
- Open the back cover of the product.
- If present, remove the insulation sheet from the battery compartment. The indicator light should illuminate for 3 seconds, confirming the device is powered on.
- Ensure the CR2032 battery is correctly installed with attention to positive and negative terminals.
2. Network Configuration (Pairing with Zigbee Gateway)
Important: This device requires a Zigbee gateway (hub) to function. It is compatible with most Zigbee hubs, including eWelink Zigbee Hub and Zigbee2MQTT. It is not compatible with Tuya or Smart Life apps/gateways, and ZHA is not recommended.
- Ensure your Zigbee gateway is powered on and in pairing mode.
- Open the eWelink App or your Zigbee management software (e.g., Home Assistant with Zigbee2MQTT).
- Navigate to the "Add Device" or "Pairing" interface within your app/software.
- On the Smart Button, long press the button for 10 seconds. The indicator LED will flash quickly, indicating it has entered network configuration mode.
- Follow the on-screen instructions in your app/software to complete the pairing process.
- Wait for the app to confirm successful pairing.
Operating Instructions
The Smart Button supports three distinct actions to trigger smart scenes:
- Single Click: A quick press and release of the button.
- Double Click: Two quick presses in succession.
- Long Press (>3 seconds): Press and hold the button for more than 3 seconds.
Creating Smart Scenes
Once paired with your Zigbee gateway, you can configure these button actions to trigger various smart scenes within your eWelink App or Home Assistant setup.
- Open your smart home application (e.g., eWelink App).
- Navigate to the "Scenes" or "Automation" section.
- Create a new scene or automation.
- Select the Smart Button as the trigger device.
- Choose the desired action (Single Click, Double Click, or Long Press).
- Define the actions to be performed when the button is pressed (e.g., turn on lights, adjust thermostat, activate "Away" mode).
Scenario Applications
The Smart Button can be placed on a table or stuck to a wall using the provided double-sided sticker, offering flexible placement options for convenient access.
Examples of scenes you can create:
- Single Press: Turn on/off a Zigbee bulb (ensure your app is in remote mode for controlling the bulb).
- Double Press: Activate "Away" mode, turning off all lights, air conditioners, fans, and other electronic devices before you leave.
- Long Press: Trigger a "Night" scene, dimming lights or closing smart curtains.
Maintenance
Battery Replacement
The device is powered by a CR2032 3V DC battery. The typical battery life is approximately 1-2 years with general use. When the battery is low, the device may become unresponsive or disconnect from the network.
- Rotate the back cover of the device counter-clockwise to open it.
- Remove the old CR2032 battery.
- Insert a new CR2032 battery, ensuring correct polarity (positive side up).
- Replace the back cover by rotating it clockwise until secure.
Cleaning
Wipe the device with a soft, dry cloth. Do not use liquid cleaners or abrasive materials.
Troubleshooting
- Device not responding:
- Check battery level. Replace CR2032 battery if necessary.
- Ensure the device is within range of your Zigbee gateway.
- Verify that the device is still paired with your Zigbee network. If not, re-pair it following the "Network Configuration" steps.
- Cannot pair with gateway:
- Confirm you are using a compatible Zigbee gateway (e.g., eWelink Zigbee Hub, Zigbee2MQTT). Tuya/Smart Life gateways are not supported.
- Ensure the gateway is in pairing mode.
- Make sure the button is in network configuration mode (LED flashing quickly after long press).
- If using Zigbee2MQTT, ensure your Zigbee2MQTT software is updated to the latest version.
- Scenes not triggering:
- Verify that the scenes are correctly configured in your smart home app (e.g., eWelink App).
- Check the conditions and actions defined for each scene.
- Ensure the linked smart devices are online and functioning correctly.
- No entity for button status in Home Assistant:
- Some users have reported that the button may not expose a direct "status" entity but rather sends events for single, double, or long presses. Configure your automations to listen for these specific events instead of a status change.
- Ensure your Zigbee2MQTT setup is correctly configured to interpret these events.
Specifications
| Parameter | Value |
|---|---|
| Wireless Protocol | Zigbee 3.0 |
| Power Supply | Battery CR2032 3V DC |
| Battery Included | Yes |
| Standby Current | <8uA |
| Control Distance | 25m - 30m (open area) |
| Dimensions | 50mm (Diameter) x 13mm (Thickness) |
| Operating Temperature | -10 °C to 55 °C |
| Working Humidity | 0% to 99% RH |
| Estimated Battery Life | 1-2 years (General use) |
| Compatible Apps | eWelink App, Home Assistant (via Zigbee2MQTT) |
| Incompatible Apps | Tuya, Smart Life |
| Certification | CE, RoHS |
User Tips
- Compatibility Check: Always ensure your existing smart home hub is a Zigbee gateway compatible with eWelink or Zigbee2MQTT. This button is explicitly stated not to work with Tuya or Smart Life.
- Home Assistant Integration: For Home Assistant users, it's recommended to use Zigbee2MQTT for integration. Be aware that the button might send events (single_press, double_press, long_press) rather than updating a direct "status" entity. Configure your automations to listen for these specific events. Keep your Zigbee2MQTT updated.
- Flexible Placement: Utilize the included double-sided sticker to mount the button on walls or other surfaces for convenient access, or simply place it on a table.
- Battery Life: While the estimated battery life is 1-2 years, actual usage may vary. Consider having a spare CR2032 battery on hand.
- Signal Range: Ensure the button is within a reasonable range of your Zigbee gateway for reliable operation.
Warranty and Support
For warranty information and technical support, please refer to the official Coolo website or contact your retailer. Keep your purchase receipt as proof of purchase.
A PDF version of this manual may be available for download from the manufacturer's support page.