1. Introduction
1.1 Safety Information
For your own safety and the safety of others, and to prevent damage to the device and vehicles upon which it is used, it is important that the safety instructions presented throughout this manual be read and understood by all persons operating or coming into contact with the device.
There are numerous procedures, techniques, tools, and parts required for servicing vehicles, as well as the skills of the person doing the work. Because of the vast number of test applications and variations in the products that can be tested with this equipment, we cannot possibly anticipate or provide advice or safety messages to cover every circumstance. It is the automotive technician's responsibility to be knowledgeable of the system being tested. It is crucial to use proper service methods and test procedures. It is essential to perform tests in an appropriate and acceptable manner that does not endanger your safety, the safety of others in the work area, the device being used, or the vehicle being tested.
Before using the device, always refer to and follow the safety messages and applicable test procedures provided by the manufacturer of the vehicle or equipment being tested. Use the device only as described in this manual. Be sure to read, understand, and follow all safety messages and instructions in this manual.
Safety Instructions
The safety messages herein cover situations Xtool is aware of at the time of publication. Xtool cannot know, evaluate or advise you as to all of the possible hazards. You must be certain that any condition and service procedure encountered does not jeopardize your personal safety.
1.2 Trademarks and Disclaimer
XTOOL is a trademark of Shenzhen Xtooltech Intelligent Co., Ltd. Copyright, registered in China, the United States, and other countries. All other marks are trademarks or registered trademarks of their respective holders.
All information, specifications, and illustrations in this manual are based on the latest information available at the time of printing. Xtool reserves the right to make changes at any time without notice. While information in this manual has been carefully checked for accuracy, no guarantee is given for the completeness and correctness of the contents, including but not limited to the product specifications, functions, and illustrations. Xtool will not be liable for any direct, special, incidental, or indirect damages, or for any economic consequential damages (including the loss of profits) as a result of using this product.
2. Product Overview
2.1 Device Description
The XTOOL TP500 is a high-efficiency, smart, and portable TPMS diagnostic tool. It combines full TPMS service with comprehensive vehicle system diagnostics.

Main Components
- Power Button: Used to power on/off the device.
- Touch-Screen: The primary interface for interaction.
- Sensor Activation Area: Used for activating TPMS sensors.
- Type-C Port: For charging and connecting to a PC.
- SD Card Slot: For expandable storage.
- Nameplate: Contains device identification information.
VCI (Vehicle Communication Interface) Indicator Light Instructions
The VCI connects the TP500 to the vehicle's OBD port.
- Green light stays on continuously: Power is connected, but not linked to the device host.
- Green light is flashing: VCI firmware update is in progress.
- Blue light stays on continuously: The device is connected but not communicating with the vehicle.
- Blue light is flashing: The device is successfully connected and communicating with the vehicle.
- Red light is flashing: VCI fault.
3. Specifications
3.1 Tablet Specifications
| Project | Specifications |
|---|---|
| Screen | 720x1440 5.45" touch screen |
| Operating Temperature | -10°C ~ 50°C |
| Storage Temperature | -40°C ~ 70°C |
| Dimension | 179.9mm*89.7mm*30.07mm |
| Weight | 0.35kg (0.77lb) |
| Wireless Function | Wifi |
| Communication Interface | Wi-fi |
| Software Update | Yes (Lifetime Free) |
| Electronic | Yes |
| Wireless Support | Wifi |
| Is Batteries Included | No (Built-in rechargeable battery) |
| External Testing Certification | CE |
| Special Features | Wifi |
| Software Version | Free Update Lifetime |
| Hardware Version | 2026 |
| Origin | Mainland China |
| Material | Plastic |
| Certification | CE |
| Item Type | Engine Analyzer |
| Warranty | 2 Years |
| Languages | 22 Kinds (English, Spanish, French, German, Polish, Portuguese, Russian, Danish, Greek, Finnish, Hungarian, Italian, Japanese, Korean, Dutch, Norwegian, Swedish, Thai, Arabic, Turkish, Vietnamese, Traditional Chinese) |
3.2 Slave Device (VCI) Specifications
| Project | Specifications |
|---|---|
| Operating Temperature | -10℃ ~ 50℃ |
| Storage Temperature | -40°C ~ 70°C |
| Dimension | 70mm*50mm*36mm |
| Weight | 0.07kg (1.70lb) |
4. Setup & Activation
For the first use, you need to activate and initialize the device. Simply follow the system prompts to complete the activation and initialization process. Upon successful activation, a confirmation message will be displayed.
4.1 Initial Setup Steps
- Select Device Language: On the initial screen, choose your preferred language.
- Connect to Wi-Fi Network: Connect the device to an available Wi-Fi network.
- Download and Install Software: After connecting to Wi-Fi, tap [Next] to download and install the necessary software package.
- Register or Log In: Proceed to [Register] if you are a new user, or [Log in] if you have an existing account.
- Product Activation Confirmation: Upon successful activation, a confirmation message will appear.
5. Operating Instructions
The XTOOL TP500 offers a wide range of diagnostic and TPMS functions. Navigate through the main menu using the touch screen to access the desired features.

5.1 TPMS Functions
Access the [tire pressure monitoring] option on the homepage to perform basic tire pressure system monitoring functions (activating tire pressure sensors, diagnosing the tire pressure system, programming tire pressure sensors, viewing learning procedures and sensor information).
5.1.1 Intelligent Mode (Vehicle Recognition)
- Turn on the device, click [TPMS] to enter the vehicle selection interface.
- Select [Intelligent Mode].
- After confirming that the ignition switch is turned on and the tire pressure device is connected to the VCI normally, wait for the VIN to be read.
5.1.2 Manual Mode (Vehicle Recognition)
- Turn on the device, click [TPMS] to enter the vehicle selection interface.
- Select [Manual Mode].
- Perform vehicle selection by choosing Market region → Brand → Model → Year of manufacture.
5.1.3 Trigger the Sensor
- Select the [Check] interface.
- Hold the device close to the sensor of the highlighted wheel (usually located at the valve), and click [Start Trigger] to activate it.
- After successfully activating the sensors, information of all activated sensors will be displayed. If any sensor fails to activate, repeat the activation procedure according to the device prompts.
- If the sensor battery is low, a low-battery icon will be displayed.

5.1.4 TPMS Diagnostic
- Select the [Diagnostics] interface. Turn on the vehicle's ignition switch, and insert the wireless slave VCI diagnostic box into the vehicle's OBD port (usually located under the steering wheel) to complete the communication connection.
- After the VCI completes the communication connection, click [Diagnose] to acquire data and perform fault diagnosis. The device will display the information of all vehicle sensors and read whether there are fault codes.
- If communication fails, check whether the connection is secure, whether the vehicle's ignition switch is turned on, or whether the vehicle model is supported, then repeat the operation.

5.1.5 Program the Sensor (4 Ways)
The XTOOL TP500 can program XTOOL TS100PRO sensors to replace 99% of faulty sensors.

- Activate Copy:
a. Enter the [Programming] page, select the tire pressure sensor to be programmed, hold it close to the upper end of the device, and click the [Activate Copy] option.
b. Select the sensor ID of the originally tested vehicle that has been activated to perform copying. - OBD Copy:
a. Enter the [Programming] page, select the tire pressure sensor to be edited, hold it close to the upper end of the device, and click the [OBD Copy] option.
b. Follow device instructions to connect to the OBD diagnostic socket of the test vehicle for communication. If communication fails, retry from the [Programming] interface.
c. After communication, the sensor SN numbers of the test vehicle will be displayed. Select the corresponding SN number and click [OBD Copy] to program. - Copy By Input:
a. Enter the [Programming] page, select the tire pressure sensor to be edited, place it close to the upper end of the device, and click the [Copy By Input] option. (Manual ID input supports one sensor at a time).
b. After scanning, enter the ID editing interface, confirm the ID format, and customize the ID. - Auto Create:
a. Enter the [Programming] page, select the tire pressure sensor to be edited, place it close to the upper end of the device, and click the [Auto Create] option.
b. After scanning, the detected sensor SN number will be displayed. Select the corresponding SN number for programming.
5.1.6 TPMS Relearn & Reset
- OBD Relearn:
a. Select the [Relearn] interface, set the vehicle gear to P (Park), and pull up the handbrake.
b. On the TP500, select the sensor, click [Start Trigger], and activate each sensor in sequence according to the order of left front, right front, right rear, left rear, and spare tire (if available).
c. After installing the tire pressure sensors, inflate all tires to the standard pressure (usually found on the door frame), and keep the vehicle stationary for 5-10 minutes.
d. Connect the TPMS tool to the vehicle's OBD interface, turn on the ignition switch, and click [OBD Learning].
e. Turn off the ignition switch and then turn it on again. Drive at a speed higher than 30km/h for more than 10 minutes to ensure the tire pressure warning light goes off. - Automatic Relearn:
a. Select the [Learning] interface. Inflate all tires to the standard pressure (usually found on the door frame) and pull up the parking brake.
b. The vehicle must remain stationary for 20 minutes to allow the control module to enter learning mode.
c. Drive the vehicle at a speed of 25-100km/h to learn the sensor ID. Reset the tire pressure value:
i. Inflate all tires to the standard pressure (usually found on the door frame), pull up the parking brake, and then turn on the ignition switch (with the engine off).
ii. Press and hold the 'Set (or ESP)' button (located near the gear shifter) until a prompt tone sounds, indicating that the learning is completed.
5.1.7 OE Query
- Turn on the device, select [OE Query], and enter the OE number list.
- After completing the selection of the OE number, you will be redirected to the 'Check' interface.
- Select the ID and click [Start Trigger] to trigger the sensor.
- Complete the activation of the sensor.
5.1.8 Sensor Test
- Turn on the device, click [Sensor Test], and switch to the sensor detection interface.
- Click [Start Detection] to get the detection result. (Only sensors from Langren Technology Co., Ltd. are supported for detection).
5.1.9 TPMS Toolbox
- Turn on the device, click [TPMS Toolbox], and switch to the tire pressure toolbox interface.
- Click on the [Key Frequency Detection] function.
- Obtain the test result.
5.2 General Diagnostic Functions
5.2.1 Diagnosis
- Open the device and click [Diagnosis] to jump to the vehicle model selection interface.
- After selecting the vehicle model, wait for the VCI firmware to be upgraded.
- Choose Automatic Detection/Manual Selection.
- For Automatic Detection: Perform an automatic scan of the condition of the vehicle modules.
- For System Selection: Select the control module to be read.
- Read ECU Information, Read DTC, Clear DTC.
- After reading is completed, [Report Details] will pop up when exiting Diagnosis. Click [OK] to save the diagnostic report to the 4.15 Report Center.
5.2.2 Auto Scan
- Turn on the device and click [Auto Scan] to enter the interface.
- Select Auto Scan or Manual Input for vehicle identification.
5.2.3 Special Functions (17+)
The XTOOL TP500 provides 17+ special functions with lifetime free updates. Note: Not all special functions can support all vehicle models; please check compatibility before purchasing.

- Oil Reset: Reset the oil service light.
- Throttle Adaptation: Reset the throttle actuators to accurately regulate throttle operations.
- BMS Reset: Register the newly replaced car battery into the ECU.
- EPS Adaptation: Perform EPS (Electric Power Steering) adaptation.
- EPB Reset: Reset the electronic parking brake.
- ABS Bleeding: Perform to bleed the brake system to restore ABS braking sensitivity.
- DPF Regeneration: Clear PM from the DPF filter through oxidation or combustion.
- Injector Coding: Code a new injector to better identify injectors for accurate fuel injection.
- TPMS Reset: Reset the TPMS system.
- SAS (Steering Angle Sensor) Reset: Clear fault steering angle sensor memories, perform reset, and turn off warning light.
- VGT Relearn: Recalibrate the variable geometry turbocharger (VGT).
- Tire Size Setting: Adjust the on-board computer to accommodate tires of different sizes.
- Suspension Calibration: Calibrate vehicle suspension.
- Gearbox Adaptation: Adapt the gearbox settings.
- Crank Sensor Relearn: Relearn the crank sensor.
- Windows Initialization: Initialize power windows.
- Sunroof Initialization: Initialize the sunroof.
- GPF Regeneration: Regenerate the Gasoline Particulate Filter.
- Camshaft Sensor Relearn: Relearn the camshaft sensor.
- Coolant Replacement: Perform coolant replacement procedures.
5.2.4 OBD II Functions
The TP500 supports full OBDII functions for comprehensive engine diagnostics.

- Read Trouble Codes (DTCs)
- Clear Trouble Codes (DTCs)
- Live Data
- Read Freeze Frame
- Read ECU Information
- Component Test
- On-Board Monitor Test
- O2 Sensor Monitoring Test
- I/M Readiness
- Read Vehicle Information (merged into Read ECU Information)
5.2.5 Report Center
- Turn on the device, select [Report Center].
- This function supports viewing user diagnostic reports. Click to access and view.
- Select the corresponding test record to obtain the diagnostic report.
- Click [Share] to pop up the email input box for report sharing.
5.2.6 Updates
- Turn on the device, click [Updates], and jump to the update package menu.
- Click the upgrade package bar to pop up specific optimization details.
- Click on the update icon corresponding to the selected upgrade package to perform the upgrade.
- Click [One - click Upgrade] to upgrade all upgradeable installation packages.
5.2.7 Settings
- Language: Set the device language.
- Unit: Set metric, imperial, or US customary units.
- Tire Pressure Settings: Market region, Pressure unit (kPa, Psi, or Bar), Temperature unit (Celsius or Fahrenheit), Sensor ID format (automatic, hexadecimal, or decimal).
- WiFi connection: Select a network to connect to the Internet.
- Display: Screen brightness (drag slider), Sleep time (15s, 30s, 1min, 5min, 10min or never).
- Storage: File Management (view files), Diagnostic storage settings (intelligent or system storage), Used space display.
- Date & Time: Time-zone settings, Time format (24-hour or 12-hour).
- About: Show device information like Model, VCI Serial Number, OS Serial Number, MAC Address, Version Number, Factory Data Reset.
- Upload test report to the cloud: Once opened, the diagnostic report can be shared with the cloud.
6. Maintenance
6.1 Battery & Charge
The device is equipped with a built-in 4500mAh/3.6V lithium-ion polymer rechargeable battery. The battery can be recharged repeatedly, but please note that as a consumable component, prolonged use will gradually reduce the device's standby time. To extend battery lifespan, avoid frequent recharging.
- Use a USB cable to connect to a PC and charge the battery.
- To charge using a Power charger:
1. Locate and open the protective cover on the device's USB port.
2. Use the USB cable adapter to connect the device and the power supply. - To maintain optimal performance, fully charge the product each time. It is recommended to charge it for at least 2 hours before the first use.
Warning:
- Only use the USB cable adapter provided in our accessories to charge this device. Damage to the product or malfunction caused by using an unapproved power source is not covered by our warranty.
- Avoid frequent recharging to extend battery lifespan.
7. Troubleshooting
- Device not powering on: Ensure the battery is charged. Connect to a power source using the provided adapter.
- VCI not connecting to device: Check the VCI indicator light. If green, power is connected but not linked; ensure proper connection to the device host. If blue, connected but not communicating; check vehicle ignition.
- VCI not communicating with vehicle: Ensure the VCI is securely plugged into the vehicle's OBD port. Check vehicle ignition is on. Verify the vehicle model is supported.
- Sensor activation/programming failure: Ensure the device is held close to the sensor. Repeat the procedure. Check sensor battery status.
- Software update issues: Ensure a stable Wi-Fi connection. Retry the update process.
- Language activation: The original language of the device is English. Other languages need to be activated by the seller. Contact support with your device serial number for activation.
8. User Tips
- Always keep your device's software updated to ensure compatibility with the latest vehicle models and access to new features.
- Before performing any diagnostic or reset function, ensure the vehicle's ignition is on and the VCI is properly connected and communicating.
- For TPMS sensor programming, try different methods (Activate Copy, OBD Copy, Copy By Input, Auto Create) if one method doesn't work for a specific sensor.
- When performing an Automatic Relearn for TPMS, ensure the vehicle remains stationary for the specified time and then drive within the recommended speed range.
- If you encounter any issues with specific vehicle models or functions, refer to the official XTOOL website or contact their support for assistance.
9. Warranty & Support
9.1 One-year Valid Warranty Period
Shenzhen Yunjia Intelligent Technology Co., Ltd. (hereinafter referred to as "the Company") warrants to the original retail purchaser of this device that, within one year from the date of delivery, under normal usage conditions, if the device malfunctions due to any defect in materials or workmanship, the Company will, upon presentation of the purchase certificate, repair or replace the device free of charge (with new products or remanufactured components) as appropriate.
Warranty Exclusions:
The above warranty rules do not apply to the following cases:
- Any product damaged due to abnormal use or conditions, accidents, improper handling, human negligence, unauthorized modification, improper use, improper installation or maintenance, or improper storage.
- Products with mechanical serial numbers or electronic serial numbers deleted, altered, or damaged.
- Damage caused by exposure to high temperatures or extreme environmental conditions.
- Damage caused by connection to or use of accessories or other products not approved or authorized by the company.
- Defects in product appearance, decorations, decorative or structural components such as frames and non-operational parts.
- Damage caused by external factors such as fire, mud, sand, battery leakage, fuse blowout, theft, or improper use of any power supply.
9.2 Service and Support
If you have any questions about this product, please contact the dealer or authorized service center in your area, or call 400-880-3086 for support and assistance from YunJia Intelligent engineers.
Shenzhen Xtooltech Intelligent Co., Ltd.
Official Website: www.xtooltech.com
Tel: +86 755 21670995 or +86 755 86267858 (China)
E-mail: supporting@xtooltech.com
10. Compliance Information
10.1 FCC Compliance
FCC ID: 2AW3IF520
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Warning:
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment can generate, use and radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
10.2 ISED Statement
IC: 29441-F520
HVIN: F520
PMN: XTireProbe
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation.
The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).
10.3 CE Declaration of Conformity
Hereby, Shenzhen Xtooltech Intelligent Co., Ltd. declares that this TPMS Diagnostic Tool, XTireProbe is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. In accordance with Article 10(2) and Article 10(10), this product is allowed to be used in all EU member states.
10.4 UKCA Declaration
Hereby, Shenzhen Xtooltech Intelligent Co., Ltd. declares that this TPMS Diagnostic Tool, XTireProbe satisfies all the technical regulations applicable to the product within the scope of UK Radio Equipment Regulations (SI 2017/1206); UK Electrical Equipment (Safety) Regulations (SI 2016/1101); and UK Electromagnetic Compatibility Regulations (SI 2016/1091) and declares that the same application has not been lodged with any other UK Approved Body.