XMSJ RH-200-SS

Contents

User Manual: 2.5 Qt Hot Water Dispenser with RO5DX 5-Stage Filtration System

Model: RH-200-SS

1. Introduction

Thank you for choosing our water dispenser. This equipment is designed to provide quality water at different temperatures (cold, warm, hot) conveniently and safely, without the need to boil water or store it in refrigerators. It is an essential tool for daily hydration, ideal for preparing hot beverages (teas, coffee), cold refreshments, or simply drinking clean water.

Before using the water dispenser, please read this manual carefully to ensure safe, efficient operation and to prolong the product's lifespan. This manual contains detailed instructions on components, preparation, usage, cleaning, maintenance, and common troubleshooting. Keep it in an accessible place for consultation when necessary, especially for safety matters.

2. Safety Precautions

The water dispenser operates with electricity and water, and features heating zones, so it is crucial to strictly follow these precautions to avoid risks of electric shock, burns, product damage, or personal injury, especially if children, pets, or elderly people are nearby.

  • The water dispenser is designed exclusively for domestic or office use (indoor spaces). Do not use it outdoors, in excessively humid places (e.g., bathrooms without ventilation, areas with spilled water), or near flammable materials (oil, alcohol, solvents), as this can cause electric shock or damage.
  • Do not touch the dispenser with wet hands while it is connected to the electrical current. Prevent water from entering the electrical connection ports, as this can cause short circuits and electric shock.
  • Keep the dispenser out of reach of small children and pets. Do not allow children to manipulate the faucets, the water tank, or the electrical connection. Prevent pets from biting the cable or the dispenser body, especially the heating zones.
  • Only use potable and clean water. Do not use contaminated, cloudy, or residual water, as this can damage the cooling/heating system and affect health.
  • Do not fill the water tank beyond the indicated maximum (“MAX” mark on the tank). If water spills, turn off the dispenser, disconnect it from the power, and dry the equipment body and the surrounding area to prevent electric shock or damage.
  • Do not use the dispenser if the tank is empty. The equipment may have dry-run protection, but avoiding use without water prolongs the lifespan of the motor and heating/cooling elements.
  • Disconnect from the electrical current when not in use, during cleaning, or if storing it. Do not leave the dispenser connected to the current for prolonged periods without use.
  • Do not disassemble, modify, or repair the dispenser on your own. Any intervention (including internal component cleaning, part replacement, or motor repair) must be performed by qualified authorized technical personnel.
  • If the dispenser falls, suffers an impact, or is damaged (e.g., broken body, frayed cable, damaged connection ports, broken faucets), disconnect it from the power immediately and do not use it until it has been checked by a technician.
  • Caution with hot water: The heating zones and the water coming out of the hot water faucet can reach high temperatures (up to 95°C), so avoid touching these areas and do not place cold glass containers directly under the hot water faucet to prevent breakage due to temperature changes.
  • Do not place heavy or hot objects on the dispenser, as this can damage the surface or internal components.
  • If you experience water leaks, turn off the dispenser, disconnect it from the power, and dry the area. Consult the troubleshooting section or contact a technician if the leak persists.
  • Do not use the dispenser if you detect strange odors, smoke, or overheating. Turn off the equipment immediately, disconnect it from the power, and contact technical service.

3. Components Overview

Before starting, identify the main components of the water dispenser. Refer to the product images for a more detailed reference (components may vary slightly depending on the model).

Hot water dispenser and dual-lever faucet
Figure 1: Hot Water Dispenser and Faucet
Express Water RO system components and filters
Figure 2: Express Water RO System Components and Filters
  1. Main Dispenser Body: The exterior part of the equipment, with a compact and elegant design, generally made of resistant plastic, with compartments for the water tank, cooling, and heating systems. It is resistant to humidity and easy to clean.
  2. Water Tank (or Bottle Loading System): Removable container (or loading area for 5L, 10L, etc. water bottles) located at the top or bottom of the dispenser, where water is stored. It has a “MAX” (maximum) and “MIN” (minimum) mark to indicate the appropriate water level.
  3. Dispensing Faucets: Outlets located on the front of the dispenser, separated by temperature: cold water faucet (generally marked with a snowflake icon or blue color), warm water faucet (sun icon or yellow color), and hot water faucet (flame icon or red color). Some models have anti-drip valves.
  4. Lever or Control Button: Part located next to each faucet, which is pressed or actuated to dispense water. Some models have touch buttons instead of levers.
  5. Heating Zone: Internal component that heats water up to temperatures between 85-95°C, ideal for teas, coffee, or hot beverages. It is protected by a heat-resistant casing.
  6. Cooling Zone: Internal component that cools water to temperatures between 5-10°C, ideal for drinking cold water. Some models use compressors or thermoelectric systems.
  7. Water Level Indicators: Transparent window or sensor with LED light, located on the side or front of the dispenser, which indicates the remaining water level in the tank.
  8. Operation Indicators: LED lights that indicate if the dispenser is connected, if the water is hot or cold, or if the tank is empty.
  9. Power Cable: Cable that connects the dispenser to an electrical power source (220-240V plug). Ensure the cable has a compatible safety plug.
  10. Base: Bottom part of the dispenser, with non-slip pads to prevent movement. Some bases have a drip tray to catch spilled water.
  11. Drain Valve (depending on model): Valve located at the bottom of the dispenser, which allows draining residual water from the tank for cleaning or maintenance.
  12. Tank Cap: Piece that closes the water tank, preventing dust or contaminants from entering and ensuring hermeticity.

4. Initial Setup

4.1 Usage Requirements

Before using the water dispenser, verify that it meets the following requirements to ensure safe and efficient operation:

  1. Adequate Space: Place the dispenser on a flat, stable, and dry surface, away from countertop edges, electronics, wooden furniture, and flammable materials. Leave a minimum space of 10 cm between the dispenser and walls or objects, so that the cooling/heating system's ventilation functions correctly.
  2. Power Source: Connect the dispenser to a compatible power source (220-240V plug) with short-circuit protection. Ensure the power cable is in good condition, without cracks, breaks, or fraying.
  3. Potable Water: Use potable and clean water to fill the tank. If using water bottles, ensure they are of good quality and not damaged.
  4. Ventilation: Ensure the dispenser area has good ventilation, especially around the cooling and heating zones, to prevent overheating.

4.2 Dispenser Preparation

  1. Disconnect the dispenser from the power source before preparing it, to avoid electric shock risks.
  2. Clean the water tank: If it's the first use or if the dispenser has been unused for a long time, rinse the tank with hot water and a neutral detergent (fragrance-free). Rinse thoroughly with potable water and dry the inside with a clean cloth.
  3. Fill the tank: Remove the tank cap (or place the water bottle in the top loading area, depending on the model) and fill the tank with potable water up to the “MAX” mark. Do not overfill to prevent spills.
  4. Close the tank: Replace the tank cap, ensuring it is tightly closed to prevent leaks. If using a water bottle, ensure it is properly adjusted in the loading area.
  5. Connect the power cable to the dispenser and to the power source. Verify that the connection is secure and that there is no water around the connection port.
  6. Turn on the dispenser: Press the power button (generally located on the front or side) and wait for the cooling and heating system to activate. The LED indicators will light up to confirm that the equipment is functioning.
  7. Wait for preparation time: Allow the dispenser to operate for 15-30 minutes for the water to reach the desired temperature (cold or hot) before dispensing.

5. Mode of Use

The water dispenser is intuitive and easy to use, with simple controls for dispensing water at different temperatures. Follow these general steps and consult your model's specific functions:

5.1 Water Dispensing

  1. Preparation: Place a container (glass, cup, pitcher) under the faucet corresponding to the temperature you desire (cold, warm, hot).
  2. Dispense cold water: Press the lever or button of the cold water faucet (marked with a snowflake icon or blue color) and hold it until the container is full. Release the lever to stop dispensing. Cold water will reach temperatures between 5-10°C.
  3. Dispense warm water (depending on model): Press the lever or button of the warm water faucet (marked with a sun icon or yellow color) and hold it until the container is full. Release the lever to stop dispensing. Warm water will reach temperatures between 30-40°C.
  4. Dispense hot water: Be careful with the high temperature. Press the lever or button of the hot water faucet (marked with a flame icon or red color) and hold it until the container is full. Release the lever to stop dispensing. Hot water will reach temperatures between 85-95°C, so avoid touching it directly.
  5. Avoid spills: Do not leave the faucets open without a container underneath. If water spills, clean the area immediately with a dry cloth to prevent slips or damage to the dispenser.

5.2 Use of Indicators

Hot water dispenser temperature dial and indicator lights
Figure 3: Temperature Setting Dial and Indicator Lights (Red: Heating to max adjustment, Green: Tank fully heated)
  1. Water level indicator: Check the transparent window or the dispenser's LEDs to see the remaining water level. When the level reaches “MIN”, refill the tank with potable water.
  2. Temperature indicators: The LEDs corresponding to each temperature (cold, hot) will light up when the water reaches the desired temperature. For example, the blue LED lights up when cold water is ready, and the red LED lights up when hot water is ready.
  3. Error indicator (depending on model): If the dispenser detects a problem (empty tank, overheating, leak), a flashing red LED will light up. Consult the troubleshooting section to resolve the problem.

5.3 Dispenser Shut-off

  1. Press the power button (“ON/OFF”) to manually turn off the dispenser.
  2. Disconnect it from the power source after turning it off, especially if you will not use it for prolonged periods (more than 24 hours).
  3. If the dispenser turns off automatically (due to an empty tank or overheating), refill the tank (if necessary) and allow the equipment to cool down before turning it back on.

6. User Tips for Efficient Use

  • Refill the tank before it reaches the “MIN” level: This prevents the dispenser from running without water and protects internal components.
  • Do not dispense more hot water than necessary: This saves energy and prevents burns.
  • Clean the faucets regularly: This prevents residue buildup and ensures smooth dispensing.
  • Ventilate the dispenser area: Keep the area around the dispenser free of objects so that ventilation functions correctly and prevents overheating.
  • Do not use the dispenser to store objects: Do not place glasses, cups, or other objects on the dispenser, as this can damage the surface or components.
  • Change the water in the tank regularly: If the dispenser is not used for a long time, empty the tank and refill it with new water to prevent bacteria buildup.

7. Cleaning and Maintenance

Regular maintenance is essential to prolong the water dispenser's lifespan, ensure its efficiency, maintain water quality, and prevent the accumulation of bacteria or residues. Follow these instructions, especially for cleaning the tank and faucets:

7.1 Daily Cleaning (or after frequent use)

  1. Turn off the dispenser and disconnect it from the power source. Allow the equipment to cool completely (especially the heating zone) before cleaning.
  2. Clean the exterior surface: Use a soft, damp cloth with a neutral detergent (fragrance-free) to wipe the dispenser's surface, removing dust, water stains, or residues. Rinse the cloth and dry the surface with a clean, dry cloth.
  3. Clean the faucets: Use a soft swab dipped in hot water to clean the faucet openings, removing any residue that may obstruct dispensing. Press the levers several times to expel residues.
  4. Clean the drip tray (if applicable): Remove the tray, empty any accumulated water, wash with neutral detergent and hot water, rinse thoroughly, and dry before replacing.

7.2 Weekly Cleaning (or every 7 days)

  1. Turn off the dispenser, disconnect it from the power, and empty the water tank: Use the drain valve (if applicable) or gently tilt the dispenser to pour the remaining water into the sink.
  2. Prepare a cleaning solution: Mix 1 liter of hot water with 2 tablespoons of white vinegar (or 1 tablespoon of baking soda) in the tank. This solution helps eliminate bacteria and residues.
  3. Let the solution sit: Allow the vinegar or baking soda solution to rest in the tank for 30-60 minutes. This helps dissolve residues and bacteria.
  4. Gently shake: Gently shake the dispenser so that the solution reaches all parts of the tank and internal tubes.
  5. Empty and rinse: Pour the cleaning solution into the sink, then rinse the tank several times with potable water to remove the vinegar or baking soda smell.
  6. Clean internal components: Use a soft swab to clean the inside of the tank, especially the connection areas with the tubes. Do not use hard brushes, as they can damage the tank.
  7. Dry completely: Dry the inside of the tank with a clean cloth or paper towel, ensuring no residual water remains. Leave the cap open for 1-2 hours to dry completely.
  8. Refill and turn on: Fill the tank with potable water, close the cap, connect the dispenser to the power, and turn it on. Dispense a small amount of water from each faucet to purge the system before use.

7.3 Additional Maintenance

  • Store the dispenser correctly: If you will not use it for a prolonged period (e.g., holidays), clean the tank thoroughly, dry the equipment completely, disconnect it from the power cable, and place it in a protective box, away from humidity and dust.
  • Do not use corrosive cleaning products: Products with chlorine, ammonia, or abrasives can damage the tank, faucets, and the dispenser's surface.
  • Check the power cable: Periodically inspect the cable for cracks, breaks, or fraying. If the cable is damaged, replace it only with an original manufacturer's cable.
  • Check faucets and valves: Periodically verify that the faucets do not leak and that the anti-drip valves function correctly. If there are leaks, contact technical service.
  • Call a technician if necessary: If the dispenser does not function correctly (does not dispense water, water does not heat/cool, there are leaks) after cleaning, contact qualified technical service.

8. Common Troubleshooting

ProblemPossible CauseSolution
Dispenser does not turn onNot connected to power; damaged power cable; faulty connection port; empty tank (automatic shut-off).Check electrical connection; replace power cable if damaged; refill water tank; try another port or outlet.
No water dispensedEmpty tank; clogged faucets due to residue; clogged internal tubes; faulty cooling/heating system.Refill water tank; clean faucets with a swab and hot water; purge the system by dispensing water; contact a technician if tubes are clogged.
Water does not heat upFaulty heating zone; heating switch off; low water in tank; insufficient preparation time.Verify heating switch is on; refill tank; wait 15-30 minutes for water to heat; contact a technician if heating zone is faulty.
Water does not cool downFaulty cooling zone; cooling switch off; low water in tank; insufficient preparation time.Verify cooling switch is on; refill tank; wait 15-30 minutes for water to cool; contact a technician if cooling zone is faulty.
Water leaksTank overfilled (beyond “MAX”); tank cap not properly closed; faulty faucets; open drain valve; broken internal tubes.Empty water to “MAX” mark; close cap tightly; check faucets and close drain valve; contact a technician if tubes are broken.
Dispenser makes excessive noiseLow water in tank; obstructed ventilation; faulty cooling motor; clogged faucets.Refill water tank; clean ventilation; clean faucets; contact a technician if motor is faulty.
Water has strange taste or odorDirty tank; old water; accumulated bacteria; residues in tubes.Clean tank with vinegar or baking soda; change water with new potable water; purge the system by dispensing water.
LED indicators do not light upDispenser not connected to power; faulty LEDs; power switch off.Check electrical connection; press power button; contact a technician if LEDs are faulty.

9. Specifications

Hot water dispenser with dimensions and key specifications
Figure 4: Hot Water Dispenser Dimensions and Key Specs
Express Water RO system with NSF certification and filter set
Figure 5: Express Water RO System with NSF Certification
  • Model: RH-200-SS
  • Color: Polished Chrome
  • Material: Stainless Steel
  • Hot Water Dispenser Capacity: 2.5 Quarts
  • Hot Water Temperature Range: 140°F to 200°F (60°C to 93°C)
  • Cold Water Temperature Range: 5°C to 10°C
  • Warm Water Temperature Range: 30°C to 40°C (depending on model)
  • Hot Water Output: Up to 60 cups per hour
  • Heating Element: 110-volt, 1300-watt stainless steel
  • Power Source: AC
  • Dimensions (Dispenser): 12 in (305 mm) H x 8 in (203 mm) W x 9 in (229 mm) D
  • Filtration System: RO5DX 5-Stage Reverse Osmosis Filtration
  • Certifications: NSF Certified (RO5DX & RO10DX to NSF/ANSI 58)
  • Contaminant Reduction: Up to 99.99% reduction of Lead, Chlorine, Fluoride, Nitrates, Calcium, Arsenic, and more.
  • Brand Name: XMSJ
  • Origin: US (Origin)

10. Warranty and Support

For any questions, technical assistance, or warranty claims, please contact the seller or manufacturer's customer service. Refer to your purchase documentation for specific warranty terms and contact information.

You can also refer to the User Manual (PDF) for additional details.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.