1. Introduction
The CNBJ-501 Digital Infrared Frequency Tester is a versatile instrument designed for testing the frequency of wireless remote controls and assessing the quality of infrared sensing. It provides clear and precise frequency readings, making it an essential tool for mechanics, car enthusiasts, and anyone involved in configuring or diagnosing remote control issues. This manual will guide you through the setup, operation, and maintenance of your device.
Video: Overview of the Digital Infrared Frequency Tester in use.
2. Product Features
- Wide Testing Range: Measures frequencies from 100MHz to 1GHz.
- Digital Display: Clear 4-bit digital display for precise frequency readings.
- Infrared Test Function: Verifies the functionality of infrared remote signals.
- Built-in Illumination: Features a lighting LED for convenience in low-light conditions.
- Durable Design: Fallproof and wear-resistant construction for long-lasting use.
- Portable: Compact size with a fall-proof rope for easy handling.
3. Setup
3.1 Unpacking
Carefully remove the Digital Infrared Frequency Tester from its packaging. Ensure all components are present:
- Digital Infrared Frequency Tester (CNBJ-501)
- Wrist Strap (pre-attached or included)
3.2 Battery Installation
The device requires one 9V battery (not included).
- Locate the battery compartment on the back of the device.
- Slide the battery cover downwards to open it.
- Insert a new 9V battery, ensuring the polarity (+/-) matches the diagram inside the compartment.
- Close the battery cover by sliding it back into place until it clicks securely.

Figure 1: Battery compartment with 9V battery.

Figure 2: Rear view of the device with battery cover.
4. Operating Instructions
Familiarize yourself with the device's controls and indicators:

Figure 3: Device layout and controls.
- Input: Frequency input area.
- IR: Infrared input LED.
- Lighting: Button to activate the illumination LED.
- ON/OFF: Power switch button.
- TX ZONE: Testing region for remote control frequency.
- Display: 4-digit LED display for frequency readings (MHz).
4.1 Powering On/Off
Press the ON/OFF button to turn the device on. The display will light up. Press the ON/OFF button again to turn the device off.
4.2 Testing Remote Control Frequency
- Turn on the device using the ON/OFF button.
- Place the remote control (e.g., car key fob) directly onto the TX ZONE (testing region) on the front of the tester.
- Press and hold the button on the remote control that you wish to test.
- Observe the frequency displayed on the screen. The reading will be in MHz.

Figure 4: Testing a car key remote frequency.
4.3 Testing Infrared (IR) Signals
- Turn on the device.
- Point the infrared emitter of the remote control directly towards the IR input LED on the tester.
- Press and hold the button on the remote control that emits an IR signal.
- Observe if the IR input LED on the tester lights up. A lit LED indicates that the remote is emitting an infrared signal.
4.4 Using the Illumination Light
Press the Lighting button to turn on the built-in illumination LED. This can be useful when working in dimly lit environments. Press the Lighting button again to turn it off.
5. Maintenance
5.1 Cleaning
To clean the device, wipe it gently with a soft, dry cloth. Do not use abrasive cleaners, solvents, or immerse the device in water.
5.2 Storage
When not in use, store the Digital Infrared Frequency Tester in a cool, dry place, away from direct sunlight and extreme temperatures. If storing for extended periods, it is recommended to remove the 9V battery to prevent leakage.
5.3 Battery Replacement
Replace the 9V battery when the display becomes dim, the device fails to power on, or readings become inconsistent. Refer to Section 3.2 for battery installation instructions.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Device does not power on. | Battery is dead or incorrectly installed. | Check battery polarity; replace with a new 9V battery. |
| Inaccurate or fluctuating frequency readings. | Remote control not placed correctly on TX ZONE; electrical interference. | Ensure remote is flat on TX ZONE. Move away from sources of electrical interference (e.g., mobile phones, signal towers, power poles). |
| IR LED does not light up during IR test. | Remote control's IR emitter is faulty; remote not pointed correctly. | Ensure remote is pointed directly at the IR input LED. Test the remote with another known working IR receiver. |
| Display is dim. | Low battery. | Replace the 9V battery. |
Note on Interference: During testing, some sources of electrical signal interference should be avoided, such as signal towers, base stations, power poles, unplugging mobile phones, sending and receiving text messages, etc.
7. Specifications
| Model Number | CNBJ-501 |
| Measuring Range | 100M-1GHZ |
| Display Type | Digital Only (4-bit LED) |
| Power Supply | 9V Battery (not included) |
| Operating Temperature | 0°C to 50°C (32°F to 122°F) |
| Working Conditions | -10°C to 40°C (14°F to 104°F), Relative Humidity <80% |
| Storage Conditions | -20°C to 50°C (-4°F to 122°F), Relative Humidity <85% |
| Dimensions (L x W x H) | Approx. 150 x 75 x 30 mm (5.9 x 2.95 x 1.18 in) |
| DIY Supplies | Electrical |
8. User Tips
- Always use a fresh 9V battery for optimal performance and accurate readings.
- When testing, ensure the remote control is held steady and flat against the "TX ZONE" for consistent results.
- Keep the device away from strong electromagnetic fields to prevent interference during measurements.
- The built-in illumination light is handy for quick checks in dark areas, but remember to turn it off to conserve battery life.
9. Warranty and Support
For warranty information, technical support, or service inquiries, please contact your original point of purchase or the seller. Keep your purchase receipt as proof of purchase.