XINYI Sini Audio XY-S350H

Contents

ABT-XY-S350H 2.1 Channel Bluetooth Power Amplifier Board User Manual

Model: XY-S350H

1. Product Information

The ABT-XY-S350H is a 2.1 channel Bluetooth audio power amplifier board designed for high-fidelity sound reproduction, featuring high bass and subwoofer output. It supports multiple audio input methods and offers robust protection mechanisms.

Key Features:

  • 2.1 Channel Audio Output (Left, Right, and Subwoofer)
  • Bluetooth Version 5.1 for stable wireless connection
  • Multiple Audio Inputs: Bluetooth, AUX, U disk, USB sound card
  • High-end encoder knob for smooth volume adjustment
  • Integrated protection mechanisms against overvoltage, undervoltage, clipping, short circuit, and overheating
  • Sinilink-APP support for Bluetooth name modification, password setting, and prompt tone control

2. Safety & Warnings

Warning!

  • This product is intended for adult use only.
  • Keep out of reach of children and pets to prevent accidental injury or ingestion.
  • Always verify that the installation is correct before powering on the device.
  • If you observe abnormal noise or equipment errors after installation, immediately power off the device and discontinue use.
  • Follow all instructions for proper use. Misuse may cause harm or damage.
  • Store the product in a dry and shady place, away from high temperatures, humidity, and direct sunlight.

3. Setup Instructions

3.1 Unpacking and Initial Inspection

  1. Carefully remove the amplifier board from its packaging.
  2. Inspect the product for any visible damage. Do not proceed with installation if any damage is found.
  3. Ensure all components listed in the package contents are present.

3.2 Wiring Diagram and Connections

Refer to the diagram below for proper connection of power, audio inputs, and speaker outputs.

Front view of the ABT-XY-S350H amplifier board showing input/output terminals, control knobs, and ports.
Figure 1: Front view of the ABT-XY-S350H amplifier board with connection points and controls.
  • Power Supply: Connect a DC 12-38V/10A power source to the DC-IN terminals. Ensure correct polarity (+ and -).
  • Audio Input:
    • AUX: Connect an external audio source (e.g., smartphone, MP3 player) via the AUX input.
    • USB: Insert a U disk for audio playback or connect to a computer as a USB sound card.
    • Bluetooth: The module will automatically enter Bluetooth pairing mode when powered on.
  • Audio Output: Connect your speakers and subwoofer to the corresponding output terminals.
    • R&L Speakers: Connect passive speakers (3-8Ω, 10-220W) to the Left and Right channel outputs.
    • Subwoofer: Connect a passive subwoofer (2-8Ω, 20-350W) to the Subwoofer output.

4. Operating Instructions

4.1 Power On/Off

Once all connections are secure, apply power to the amplifier board. The board will power on automatically.

4.2 Volume Adjustment

Use the high-end encoder knobs on the front panel to adjust the following:

  • Main Volume: Adjusts the overall output volume.
  • Treble: Adjusts the high-frequency response.
  • Bass: Adjusts the low-frequency response for the main channels.
  • Subwoofer Volume: Adjusts the dedicated volume for the subwoofer output.

4.3 Audio Input Selection

The amplifier board automatically detects and switches between available audio inputs (Bluetooth, AUX, U disk, USB sound card). Prioritize the desired input by connecting it.

4.4 Bluetooth Pairing

  1. Ensure the amplifier board is powered on.
  2. On your Bluetooth device (e.g., smartphone), search for available Bluetooth devices.
  3. Select the amplifier board's Bluetooth name (default or custom) to pair.
  4. A prompt tone will indicate successful pairing.

The amplifier board supports the Sinilink-APP for advanced control:

  • Modify the Bluetooth name of the device.
  • Set a Bluetooth password for secure connections.
  • Toggle the prompt tone (on/off).

5. Maintenance

  • Keep the amplifier board clean and free from dust. Use a soft, dry cloth for cleaning.
  • Avoid exposing the device to liquids or excessive moisture.
  • When not in use for extended periods, store the product in a dry, shaded area, away from extreme temperatures and direct sunlight.
  • Ensure proper ventilation around the amplifier board to prevent overheating.

6. Troubleshooting

  • No Sound:
    • Check all audio input and output connections.
    • Ensure the power supply is correctly connected and providing sufficient voltage (DC 12-38V/10A).
    • Verify that the volume knobs are not set to minimum.
    • Confirm the correct audio input source is selected or active.
  • Abnormal Noise or Distortion:
    • Immediately power off the device.
    • Check for loose or incorrect wiring.
    • Ensure the power supply is stable and free from interference.
    • Verify speaker impedance matches the amplifier's specifications.
  • Bluetooth Connection Issues:
    • Ensure the amplifier board is in pairing mode.
    • Delete previous pairings on your Bluetooth device and try reconnecting.
    • Move your Bluetooth device closer to the amplifier board.
  • Overheating:
    • Ensure adequate ventilation around the amplifier board.
    • Check if speaker impedance is too low, causing excessive load.
    • The built-in protection mechanism will shut down the device if it overheats. Allow it to cool before resuming use.

7. Specifications

The following table details the technical specifications of the ABT-XY-S350H amplifier board:

Back view of the ABT-XY-S350H amplifier board showing a label with detailed product specifications.
Figure 2: Back view of the ABT-XY-S350H amplifier board with specifications label.
Feature Detail
Product Model XY-S350H
Product Name 2.1 Channel Bluetooth Audio Power Amplifier Board
Power Supply DC 12-38V / 10A (above)
Bluetooth Version 5.1
Audio Input Bluetooth + AUX + U disk + USB sound card
Audio Channels 2.1 Channel
Audio Output Left & Right Channels + Subwoofer
Frequency Range 20Hz - 20kHz
Volume Adjustment High-end encoder knob adjustment
Max Output Power (L&R) 220W/3Ω-36VDC, 175W/4Ω-36VDC, 100W/8Ω-36VDC
Max Output Power (Subwoofer) 355W/2Ω-36VDC, 250W/3Ω-36VDC, 195W/4Ω-36VDC
Protection Mechanism Overvoltage, Undervoltage, Clipping, Short Circuit, Overheating
Unique Function Sinilink-APP support (Bluetooth name, password, prompt tone)
Product Size 130mm x 116mm x 27mm
Material ABS

8. User Tips

  • For optimal sound quality, ensure your power supply meets or exceeds the recommended 10A current rating, especially when driving high-power speakers.
  • Utilize the Sinilink-APP to customize your Bluetooth experience, such as setting a unique name for easier identification in crowded Bluetooth environments.
  • Experiment with the separate Treble, Bass, and Subwoofer Volume controls to fine-tune the audio output to your specific speakers and listening preferences.

9. Manufacturer & Support

Manufacturer Information:

Manufacturer: Huizhou xiaolin technology co., ltd
Address: Room 02, room no. 02, 20th floor, building 6, no. 17 people's south 4th road, shuikou street office, huicheng district, huizhou city (office only)
Email: N6X3rP2BHYZRU@163.com
Phone: 8618927321281

EU Authorized Representative:

Representative: CET PRODUCT SERVICE LTD.
Address: Ludwigsburg Osterholzallee 144
Email: info@cetproduct.com

Compliance Information:

This product must comply with all applicable safety and regulatory requirements in the market where it is sold, including those related to electrical safety, electromagnetic compatibility, and environmental compliance. Conformity marking (e.g., CE) and related documentation may be required.

Additional Resources:

For a comprehensive user manual and additional documentation, please refer to the official PDF document: User Manual (PDF)

© 2024 XINYI Sini Audio. All rights reserved.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.