VGETTING X-pander DRL Headlight

Contents

User Manual: VGETTING DRL Headlight Turn Signal Front Bumper Lamps for Mitsubishi X-pander

Model: X-pander DRL Headlight | Brand: VGETTING

1. Safety & Warnings

Please read all instructions carefully before use. Failure to follow these instructions may result in damage to the product or personal injury.

  • Warning: Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture beyond its IP67 rating.

2. Setup (Installation Instructions)

2.1. Preparation Work (Safety First)

  1. Power off when parking: Park the car steadily and engage the handbrake.
  2. Disconnect Battery: Be sure to disconnect the negative cable of the battery to prevent electrical hazards.
  3. Remove Old Light: Open the tailgate, locate and remove the tail light repair cover from the inside. Disconnect the existing plug, unscrew the fixing nut, and carefully pull out the old lamp from the outside.

2.2. Install the New Light (Test First, Then Fix)

  1. Pre-testing: First, connect the new light plug to the original car harness. Reconnect the battery temporarily. Turn on the power and test whether the brake lights, turn signals, reverse lights, and driving lights are all lit up normally.
  2. Formal Installation: After confirming that the function is normal, disconnect the battery again. Align the new light with its designated position and install it. Tighten all the fixing nuts from the inside. Finally, secure the electrical plug and replace the maintenance cover.
Wiring diagram for DRL Headlight Turn Signal Lamp

Figure 2.2.1: Wiring Diagram. Connect yellow wire to Turn Signal Light, black wire to Negative, red wire to ACC.

Before and After installation of DRL Headlight Turn Signal Lamp on Mitsubishi X-pander

Figure 2.2.2: Installation Effect - Before and After comparison on a Mitsubishi X-pander.

3. Operating Instructions

These DRL (Daytime Running Light) units feature dual-color functionality:

  • White Light: Functions as the Daytime Running Light in normal driving mode.
  • Yellow Light: Functions as the Turn Signal Light when activated.

3.1. Final Inspection

  1. Function Review: Reconnect the battery and thoroughly check all lighting functions (DRL, turn signals) once more to ensure proper operation.
Lighting effect of DRL and Turn Signal modes

Figure 3.1.1: Lighting Effect - Demonstrates the white DRL and yellow turn signal illumination.

Video 3.1.1: Product Display and Lighting Effects - A visual demonstration of the DRL units in operation.

4. Maintenance

4.1. Sealing Inspection

After washing the car or exposing the lights to water, check whether there is severe water ingress or fogging inside the lamp. Slight fogging can light up and dry normally. If severe water ingress occurs, inspect the seals and connections for proper fitment.

IP67 Waterproof feature of the DRL units

Figure 4.1.1: IP67 Waterproof Feature - The units are designed to be waterproof and durable.

4.2. General Care

  • Clean the light surfaces regularly with a soft cloth and mild cleaning solution to maintain clarity and light output.
  • Avoid using abrasive cleaners or harsh chemicals that could damage the ABS housing or LED components.

5. Troubleshooting

ProblemPossible CauseSolution
Lights do not turn onIncorrect wiring, loose connection, blown fuse, faulty LED unit.Check wiring connections against the diagram. Ensure all plugs are secure. Check vehicle's fuse box. If problem persists, contact support.
Only one light worksFaulty wiring to one unit, damaged unit.Verify wiring for the non-working unit. Test connections. If wiring is correct, the unit may be faulty.
Water ingress or fogging inside lightImproper sealing during installation, damaged housing.For slight fogging, it may dissipate. For severe ingress, re-check installation seals and ensure the unit is properly seated. If housing is damaged, replacement may be necessary.
Turn signal not flashing yellowIncorrect connection to turn signal circuit.Ensure the yellow wire is correctly connected to the vehicle's turn signal light circuit as per the wiring diagram.

6. Specifications

FeatureDetail
Product NameDRL Headlight Turn Signal Front Bumper Lamp
Model CompatibilityMitsubishi X-pander Eclipse Cross 2017-2020
Brand NameVGETTING
Light SourceLED
Voltage12V
MaterialABS, LED
Waterproof RatingIP67
Light ColorWhite (DRL), Yellow (Turn Signal)
Lumens3400LM
Wattage10W
Item Weight1.2 kg
Package DimensionsLength: 37 cm, Width: 36 cm, Height: 10 cm
Package Weight1.3 kg
CertificationCCC, Dot, ECE
Special FeaturesSuper Bright, Long Lifespan, Waterproof
Product detail showing ABS housing and dual-color lights

Figure 6.1.1: Product Detail - Illustrates the ABS housing and dual-color light design.

Diagram showing product dimensions

Figure 6.1.2: Product Dimensions - Detailed measurements of the DRL unit.

7. User Tips

Based on common user experiences, consider the following tips for optimal performance:

  • Always double-check vehicle compatibility (year, make, model) before purchasing to ensure a perfect fit.
  • When installing, ensure all electrical connections are tight and properly insulated to prevent short circuits or moisture ingress.
  • If you are unsure about the installation process, it is recommended to seek professional assistance.

(Note: Specific user tips from reviews.txt and qa.cleaned.json would be included here if provided.)

8. Frequently Asked Questions (FAQ)

Q: Is this product a direct replacement for my original lights?
A: Yes, these DRL units are designed for quick and easy installation, directly replacing your stock units without modifications.
Q: What is the function of the different light colors?
A: The white light functions as a Daytime Running Light, and the yellow light functions as a Turn Signal Light.
Q: Is the product waterproof?
A: Yes, the product has an IP67 waterproof rating, ensuring durability against various weather conditions.

(Note: More specific FAQs from qa.cleaned.json would be included here if provided.)

9. Warranty & Support

9.1. Manufacturer Information

Manufacturer: Guangzhou Camel Technology Co., Ltd.
Address: No.4 West Fangxin Road, Fangcun Avenue, Liwan District, Guangzhou City, Guangdong Province

9.2. EU Authorized Representative

Representative: MJCM SAR
Address: 78 Avenue des Champs Elysees Office 326, Paris, France
Contact: mjcm190928@gmail.com, 0033 752907452

9.3. Compliance Information

This product holds certifications including CCC, Dot, and ECE. An Attestation of Compliance is available, issued by HUT on April 8, 2021, confirming adherence to relevant directives.

For further details or a comprehensive user manual, please refer to the official PDF document: User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.