JIKONG JK BMS Monitor LCD Display

Contents

JK BMS Monitor LCD Display User Manual

Model: JK BMS Monitor LCD Display Series

Brand: JIKONG

1. Introduction

This manual provides comprehensive instructions for the JIKONG Smart BMS LCD Display series, designed to monitor lithium battery systems. These displays are available in various sizes (2.0, 3.2, 4.3, 7.0 inches) and offer real-time data on voltage, current, capacity, and system status. Please read this manual carefully before installation and operation to ensure proper use and longevity of your device.

Various JK BMS LCD Display sizes
Overview of JK BMS LCD Display models, including 2.0, 3.2, 4.3, and 7.0-inch versions.

2. Setup and Installation

2.1. Display Installation

  1. Step 1: Embed the HMI (Human Machine Interface)
    Carefully insert the display unit into the pre-cut opening on your device or panel.
  2. Step 2: Secure with Buckles
    As shown in the diagram below, place the provided buckles into the mounting holes on the display's sides to hold it in place.
  3. Step 3: Tighten Screws
    Tighten the screws to firmly fix the HMI display to the device, ensuring a stable and secure installation.
4.3-inch Touch Universal Screen with dimensions
Jikong 4.3-inch Touch Universal Screen, showing panel size 140*98 (mm) and mounting hole size 129*87 (mm).
Jikong 4.3-inch Touch Display wiring diagram
Wiring diagram for Jikong 4.3-inch Touch Display, compatible with all JIKONG BMS. Includes Cable A (280mm), Cable B (280mm), Cable C (2600mm), and Switch Button Cable Length.

2.2. External Interfaces and Wiring

The display features a user interface for power supply and serial signal connection, utilizing a HY2.0mm-8P horizontal patch socket. It also includes an SD card interface for data storage or firmware updates.

Jikong 3.2-inch Display with cable interface and dimensions
Jikong 3.2-inch Display showing panel size 100.5*61.5 (mm), mounting hole size 95*56 (mm), and cable interface. Supports all protection board types and RS485 communication.
3M Aviation Plug Extension Cable
3M Aviation Plug Extension Cable for 4.3" Universal Display, showing the 5-pin connector.

2.3. Pin Definitions (HY2.0mm-8P)

Pin NumberPin NamePin DescriptionPin NumberPin NamePin Description
1GNDGround5NCNot Defined
2GNDGround6485-Serial RS-485 Signal B
3485+Serial RS-485 Signal A7VCCPower Supply
4NCNot Defined8VCCPower Supply

3. Operation

3.1. Basic Functions

  • Power On: When the BMS is powered off, press the button once to activate and power on the BMS.
  • Power Off: When the BMS is powered on, press and hold the button for 2 seconds to power off the BMS.
  • Standby Mode: If there is no charging/discharging current and no button operation, the screen will automatically turn off after 35 seconds to conserve power.
  • Discharging State: The display will remain continuously on when the current is greater than 0, indicating active discharge.
  • Touchscreen Models (e.g., 4.3-inch Touch Display): Tap the touchscreen to switch languages and navigate through menus. You can view real-time status, individual cell voltages, and fault alerts directly on the screen.
3.2 LCD RS485 display with button
Jikong 3.2-inch Display with BMS Switch Button and 40cm connecting cable.

3.2. Product Overview Video

An overview of the JIKONG Smart LCD Display, showcasing its features and components.

4. Maintenance

To ensure optimal performance and longevity of your JIKONG BMS LCD Display, follow these general maintenance guidelines:

  • Cleaning: Use a soft, dry cloth to gently wipe the screen and casing. Avoid abrasive cleaners or solvents that could damage the display surface.
  • Environmental Conditions: Operate and store the display within the specified temperature and humidity ranges to prevent damage. Avoid direct sunlight and extreme temperatures.
  • Connection Integrity: Periodically check all cable connections to ensure they are secure and free from corrosion or damage.

5. Troubleshooting

If you encounter issues with your JIKONG BMS LCD Display, consider the following common troubleshooting steps:

  • Display Not Turning On: Ensure the power supply is correctly connected and within the specified voltage range (6V-36V). Check the power button operation as described in the 'Operation' section.
  • No Data Displayed: Verify that the communication cables (RS485 or TTL) are securely connected to both the display and the BMS. Check the BMS for proper operation.
  • Incorrect Readings: Confirm that the display is compatible with your specific BMS model and that all settings are correctly configured.
  • Fault Alerts: If the display shows a 'Fault' message, refer to your BMS manual for specific error code interpretations. Common faults include overcurrent, over-discharge, overcharge, and short circuit protection.

6. Specifications

6.1. Overall Parameters

ParameterData
Display TypeTFT
Size / Resolution95.0mm (W) × 53.9mm (H) / 480*272
Display Color65K True Color
Backlight Type / BrightnessLED / 300nit/m2
Viewing Angle L/R/U/D70°/70°/50°/70°
Operating / Storage Temperature-20 ~ +70°C / -30 ~ +85°C
SD Card InterfaceSD / SDHC

6.2. Power Supply

ParameterMin ValueMax Value
Supply Voltage (with reverse connection protection)6V36V
Power Consumption1.4W (12V@116mA)

6.3. Working Environment and Reliability Parameters

ParameterTest EnvironmentMin ValueTypical ValueMax ValueUnit
Operating Temperature12V Voltage, 60% Humidity-202570°C
Storage Temperature--302580°C
Operating Humidity25°C10%60%90%RH

6.4. Product Features

  • Charging Current: 10A
  • Usage Scenario: Power BMS, Energy Storage BMS
  • Certification: CE, RoHS
  • Balance Function: Active Balanced BMS
  • Hardware or Smart: SMART BMS
  • Charge and Discharge Port: Common Port BMS
  • Type: LIFEPO4 Battery BMS
  • Origin: Mainland China
  • Function: Overcurrent Protection, Over Discharge Protection, Overcharge Protection, Short Circuit Protection

7. User Tips

  • Ensure all connections are secure and properly insulated before powering on the system to prevent short circuits or damage.
  • Regularly check the display for any fault alerts or abnormal readings to maintain optimal battery health and prevent potential issues.
  • For touchscreen models, familiarize yourself with the interface to quickly navigate and access critical information or change settings.
  • Keep the display clean and free from dust and moisture to ensure clear visibility and proper functioning of the screen and buttons.

8. Warranty and Support

For detailed product information, technical specifications, and advanced troubleshooting, please refer to the official user manual PDF available at: JIKONG BMS LCD Display User Manual (PDF).

For any technical support, warranty inquiries, or further assistance, please contact JIKONG customer service through their official channels.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.