JIKONG V19 Smart BMS

Contents

JIKONG Smart BMS V19 User Manual

Lithium Battery Active Balance Protection Board

1. Introduction

The JIKONG Smart BMS V19 is an intelligent protection board designed for high-capacity series lithium battery packs. It offers comprehensive management features including voltage acquisition, high-current active balancing, overcharge, over-discharge, overcurrent, and over-temperature protection, a coulomb meter, Bluetooth communication, and optional GPS remote functionality. This BMS is compatible with LiFePo4, Li-ion, and LTO battery types.

The protection board utilizes energy transfer active balancing technology, ensuring maximum continuous balancing currents of 1A/2A. This technology significantly improves battery consistency, extends battery life, and delays battery aging.

A dedicated mobile APP (available for Android and iOS) connects via Bluetooth, allowing users to monitor battery status, modify parameters, and control charge/discharge switches. Its compact size and full functionality make it suitable for various applications such as small sightseeing vehicles, mobility scooters, shared cars, high-power energy storage systems, base station backup power supplies, and solar power stations.

2. Key Features

  • LED Bluetooth status indicator
  • APP Bluetooth remote operation
  • Battery capacity calculation
  • High precision voltage acquisition (±3mV)
  • High precision current acquisition
  • Information screen display support
  • Accurate time logging
  • Optional RS485 support
  • Optional CAN support
  • Optional ACC detection function
  • Optional heating function
  • Parallel function support
  • Optional alarm function
  • Concatenation function support
  • GPS communication support
  • Charge overcurrent protection
  • Charge overvoltage protection
  • Charge over temperature protection
  • Low temperature protection during charge
  • Discharge overcurrent protection
  • Discharge undervoltage protection
  • Discharge over temperature protection
  • Short circuit protection

3. Package Contents

The JIKONG Smart BMS V19 package includes all necessary accessories for easy installation.

Diagram showing the JIKONG BMS, switch, NTC temperature sensor, and two sampling lines.
Figure 3.1: Packing List. Includes BMS x 1, Switch x 1 (50cm), NTC x 1 (40cm), Sampling line B x 1 (70cm), Sampling line A x 1 (70cm).
Image showing the contents of the box: BMS unit, various cables, temperature sensors, and mounting screws.
Figure 3.2: What's in the Box? All accessories included for easy installation.
Video 3.1: Product Unboxing. This video demonstrates the unboxing process and shows the components included in the package.

4. Setup and Installation

4.1. APP Installation

To manage and monitor your JIKONG Smart BMS, you need to install the dedicated mobile application. The Android APP requires Android Version 7 minimum.

QR code for JIKONG BMS APP download.
Figure 4.1: Scan this QR code to download the JIKONG BMS APP. For iOS, search "JIKONG BMS" in the App Store. For Android, search "JK BMS" in the Google Play Store.

4.2. Device Activation

Before powering on the protection board, ensure all balance cables are correctly connected, and the P- and B- terminals are properly wired. Verify that the protection board is securely fixed to the battery pack. Incorrect connections can lead to abnormal operation or damage.

The protection board does not have a power-on control switch. It is designed for charging activation: the charger voltage must be 2V higher than the battery voltage. After battery assembly, connect the charger to activate the BMS.

Alternatively, the BMS can be activated via a key switch or the display screen. If you have the optional display screen and button, simply connect the cable to the display interface and press the button to activate.

4.3. Wiring Diagram and Installation Method

The JK-BxA8S-20PS series protection board is suitable for 3-8 series lithium battery packs. The specific wiring method varies depending on the number of cells in your battery pack. Refer to the diagram below for detailed connections.

Wiring diagram for JIKONG JK-BxA8S-20PS BMS, showing connections for load, charger, heating wire, temperature control switch, and battery cells.
Figure 4.2: JK-BxA8S-20PS Wiring Diagram. This diagram illustrates how to connect the BMS to the battery pack, load, charger, heating elements, and temperature sensors.

Connector and LED Definitions:

CouplerType of ConnectorInterface NamePin NumberPin NameDefinition
P1XH-10AW-2.54Balance with Acquisition interface1B-Total negative battery
2B1The first battery positives
3B2The second battery positive
4B3The third battery positive
5B4The fourth battery positive
6B5The fifth battery positive
7B6The sixth battery positive
8B7The seventh battery positive
9B8The eighth battery positive
10B+Protection board power supply, connected to the battery
P2 (Optional)A1254WF-2ABuzzer interface1GNDBuzzer power negative
2VCCBuzzer power supply positive
P3 (Optional)A1254WF-4ACommunication interface1CAN_LCAN signal negative terminal
2CAN_HCAN signal positive terminal
3RS485_ARS485 signal positive terminal
4RS485_BRS485 signal negative terminal
P41.25T-4PWTUART interface1GNDPower/signal ground
P5HY2.0-4P4 external optional Temperature interface1T3AThird temperature sensor pin A
2T3BThird temperature sensor pin B
3T4AFourth temperature sensor pin A
4T4BFourth temperature sensor pin B
P6HY2.0-4PTemperature interface1T1AFirst temperature sensor pin A
2T1BFirst temperature sensor pin B
3T2ASecond temperature sensor pin A
4T2BSecond temperature sensor pin B
P7A1254WF-6ADisplay interface1K-Activation signal negative electrode
2K+Activate the positive signal
3GNDPower negative (Negative terminal)
4BDisplay RS485 signal negative
5ADisplay RS485 signal positive
6VCCDisplay power output
P8A1254WF-3AParallel interface1P-statusParallel module status signal
Heating Wire16AWG-Orange-15CM (Optional)Heating element negative electrode1HT-Heater element negative electrode
D1Bluetooth connection indicatorSteady on when connected, blinking when disconnected.
P-Connect to external load or negative terminal of charger, equipped with M6 screws.
B-Connect to the negative battery terminal, equipped with M6 screws.

5. Operating Instructions

5.1. Active Equalization

The BMS uses active equalization to transfer energy from higher voltage cells to lower voltage cells, minimizing energy loss. Before using this function, set the basic battery parameters in the APP, including cell count, battery capacity, trigger equalization differential pressure (default is acceptable), voltage calibration, and current calibration. The default balance current is 1A/2A, adjustable based on battery capacity. If not needed, disable the balancing switch in the APP's BMS control page.

Screenshot of the JIKONG BMS mobile app showing real-time data visualization, historical data, fault alarms, and remote parameter tuning.
Figure 5.1: Smart Bluetooth APP Control. Real-time data visualization, historical data, fault alarms, remote tuning, and parameter lock are supported on both iOS and Android systems.

5.2. UART and Display Interface

The BMS includes a UART interface for optional GPS integration, allowing for battery location tracking. A display interface is also provided for connecting JIKONG's display screen, offering convenient access to battery information.

Image of a JIKONG 3.2-inch LCD display unit with dimensions 100x62x12mm and a 50cm cable.
Figure 5.2: JIKONG 3.2-inch LCD Display. Dimensions: 100*62*12mm with a 50cm length cable.

5.3. Heating Function (Optional)

For low-temperature conditions, the optional heating function uses a resistance heater or heating film to warm the battery, preventing reduced activity and ensuring proper charging/discharging. The designed heating current is 20A. Users can enable/disable this function via the APP's BMS control page based on ambient temperature. It is recommended to use a temperature control switch (45°C to 65°C normally closed type) in series with the heating circuit as a secondary protection.

5.4. Alarm Function (Optional)

The BMS supports an optional alarm function. It will alert users when it detects safety risks such as over-temperature, overcharge, or over-discharge.

5.5. Battery Parallel Function

The BMS supports battery pack parallel functionality for energy storage applications. This requires a parallel module and disabling the "disable charging current limiting" function in the APP.

5.6. ACC Detection Function (Optional)

The optional ACC detection function enables discharge. This can be achieved by applying a voltage between ACC+ and ACC- (20V-100V) or by directly short-circuiting ACC+ and ACC-. Additionally, dedicated C_detect+ and C_detect- interfaces are provided for charger detection (12V signal) to enable charging.

5.7. Protection Features

  • Charge Overvoltage Protection & Recovery: Standard feature. Users can set individual cell overcharge protection and recovery voltages via the APP. If any cell exceeds the set overvoltage during charging, the BMS will stop charging. Charging resumes when all cells drop below the recovery voltage.
  • Discharge Undervoltage Protection & Recovery: Standard feature. Users can set battery undervoltage protection, recovery, and automatic shutdown voltages via the APP. If any cell drops below the undervoltage protection during discharge, the BMS will stop discharging. Discharge resumes when all cells are charged above the recovery voltage. If any cell drops below the automatic shutdown voltage, the BMS will shut down.
  • Charge Overcurrent Protection & Recovery: Standard feature. Users can set continuous charging current, overcurrent delay, and recovery time via the APP. If charging current exceeds the set limit for the specified delay, charging stops. Charging resumes after the recovery time.
  • Discharge Overcurrent Protection & Recovery: Standard feature. Users can set continuous discharge current, overcurrent delay, and recovery time via the APP. If discharge current exceeds the set limit for the specified delay, discharging stops. Discharging resumes after the recovery time. (Note: Max continuous discharge current cannot exceed 200A).
  • Over-temperature Protection & Recovery: Standard feature for charge and discharge. Users can set charge/discharge over-temperature protection and recovery values via the APP. If the BMS detects temperatures above the set limit, it will stop the respective operation. Operation resumes when temperatures fall below the recovery value.
  • Low-temperature Protection & Recovery: Standard feature for charging. Users can set charge low-temperature protection and recovery values via the APP. If the BMS detects temperatures below the set limit, it will stop charging. Charging resumes when temperatures rise above the recovery value. Heating function is recommended for extremely cold regions.
  • Short Circuit Protection & Recovery: Standard feature. The current to trigger short circuit protection is not user-settable. Users can set the short circuit protection delay (µs) and recovery time (S) via the APP. If a short circuit occurs, the BMS will stop operation and resume after the recovery time. Adjusting the delay can help prevent false triggers due to high instantaneous currents from chargers or loads.

5.8. Emergency Switch

The BMS includes a standard emergency switch function. If issues like over-temperature, over-discharge, over-charge, or cell string drops occur during normal use, activating the emergency switch in the APP's BMS control page will enable charge and discharge for 30 minutes. This provides an emergency operational window. Even if a cell reaches automatic shutdown voltage during this period, the BMS will continue to operate until the 30-minute cycle ends, preventing dangerous situations.

5.9. Intelligent Sleep

The BMS features a standard intelligent sleep function, which can be enabled or disabled via the APP. Its purpose is to reduce the BMS's energy consumption from the battery when in standby (charging/discharging current less than 1A for 26 consecutive hours). To reactivate the BMS, use the button or connect a charger.

5.10. Communication Function

The BMS supports optional CAN and RS485 communication. Users can select these options and configure the multiplexed ports via the APP. Address and communication protocol settings can be adjusted based on requirements. Refer to the JIKONG Protection Board communication protocol document for details.

JIKONG Home energy storage BMS V19 Version compatible with various inverter communication protocols like Deye, Pylontech, Growatt, Victron Energy, INVT, Goodwe, SMA, Voltronic Power, SNE, MUST.
Figure 5.3: JIKONG Home Energy Storage BMS V19 Version. Compatible with mainstream inverter communication protocols in the market.

6. Specifications

6.1. Product Appearance and Dimensions

The JIKONG JK-BxA8S-20PS series protection board has dimensions of $152.25mm imes 127.26mm imes 15.6mm$.

Top-down view of the JIKONG BMS board, showing its compact design and various connection points.
Figure 6.1: Product Appearance. The BMS board features a clean layout with clearly marked terminals.
Technical drawing showing the dimensions of the JIKONG JK-BxA8S-20PS BMS in millimeters.
Figure 6.2: JK-BxA8S-20PS Dimensions. The board measures 152.25mm in length, 127.26mm in width, and 15.6mm in height.

6.2. Main Parameters

ItemParameterUnit
Supply voltage7.5-36V
Series withstand voltage100V
Operating power consumption<1300mW
Operating temperature-30-70°C
Maximum number of collection strings8String
Maximum balancing current1A / 2AA
Maximum charging current200A
Maximum discharge current200A
Maximum instantaneous current400A
Maximum internal loop resistance0.35mΩ
Protective plate size152.25*127.26*15.6mm
Finished weight424g
Support maximum series battery pack12V (6 pack) / 24V (3 pack)

6.3. Default Parameters

The following table outlines the default parameters for different battery types. These can be adjusted via the APP.

ParameterLi-ion (Ternary)LiFePo4LTO (Lithium Titanate)Unit
Balancing initial voltage332V
Maximum balancing current1A / 2A1A / 2A1A / 2AA
Unit overcharge voltage4.23.62.7V
Single overcharge protection recovery4.183.552.65V
Monomer undervoltage protection2.822.61.8V
Single undervoltage protection recovery2.852.651.85V
Automatic shutdown voltage2.82.51.7V
SOC-0% voltage2.92.61.85V
SOC-100% voltage4.183.52.65V
Trigger balancing differential pressure0.010.010.01V
Charging overcurrent protection delay303030S
Charge overcurrent protection release time606060S
Discharge overcurrent protection delay300300300S
Discharge overcurrent protection release time606060S
Short-circuit protection delay555µs
Short circuit protection release time303030S
Charging overtemperature protection temperature707070°C
Charge overtemperature restore temperature606060°C
Discharge overtemperature protection temperature707070°C
Discharge overtemperature recovery temperature606060°C
Charging low temperature protection temperature-20-20-20°C
Charge low temperature to restore temperature-10-10-10°C
MOS Overtemperature protection temperature100100100°C
MOS Overtemperature protection recovery temperature808080°C
Device address000/

7. User Tips

  • Parallel Setup: The JIKONG Smart BMS is confirmed to work well in 24V parallel setups, providing reliable performance.
  • Quality Assurance: Users consistently report good product quality and construction.
  • Packaging: The product is typically well-packaged, ensuring safe delivery.

8. Troubleshooting

8.1. Inaccurate Voltage Readings

  • Measure the actual total voltage of the battery pack with a multimeter.
  • Enter this actual total voltage into the "voltage calibration" setting on the APP's parameter setting page.

8.2. Inaccurate Current Readings

  • Ensure that both the B- and P- terminals of the protection board are connected with two 7AWG wires in parallel. Failure to do so may lead to current errors.
  • Measure the actual current of the battery pack with a clamp meter.
  • Enter this actual current into the "current calibration" setting on the APP's parameter setting page. Higher actual currents lead to higher calibration accuracy.

8.3. Inaccurate Capacity Readings

  • The initial capacity estimated when the protection board is first powered on is often inaccurate.
  • For accurate calibration, fully discharge the battery pack to its cut-off voltage, then fully charge it without interruption. The capacity will be calibrated during this process.

8.4. Inconsistent String Number

  • Verify that the "unit quantity" in the APP's parameter settings is correctly configured to match your battery pack's string count.
  • If there is no voltage reading for two or more strings in the middle of the pack, check if the acquisition cable has become disconnected.

9. Warranty and Support

The JIKONG Smart BMS V19 comes with a 12-Month Warranty and professional support. For any technical assistance or warranty claims, please contact JIKONG customer service.

Image showing a table of full specifications and comparison, along with icons for 3-Year Technical Support and 2-Year Warranty.
Figure 9.1: Warranty Information. The product includes 3-Year Technical Support and a 2-Year Warranty.

© 2025 JIKONG. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.