Halnziye HY510 (0.5G)

Contents

Halnziye HY510 Thermal Grease (0.5G) User Manual

For CPU, GPU, and LED Heat Dissipation

1. Introduction

The Halnziye HY510 Thermal Grease is a high-performance silicone-based compound designed to improve heat transfer between your CPU, GPU, or LED components and their respective heatsinks. Proper application of thermal grease is crucial for maintaining optimal operating temperatures and extending the lifespan of your electronic devices.

2. Safety Information

  • Keep out of reach of children.
  • Avoid contact with eyes and skin. In case of contact, rinse thoroughly with water.
  • Do not ingest. If swallowed, seek medical attention immediately.
  • Use in a well-ventilated area.
  • Store in a cool, dry place away from direct sunlight.

3. Package Contents

  • 1 x Halnziye HY510 Thermal Grease Syringe (0.5G)
Single syringe of Halnziye HY510 thermal grease

Image: A single syringe of Halnziye HY510 thermal grease, typically 0.5g, used for applying the compound.

4. Specifications

Attribute Value
Type Thermal Grease
Model Number HY510 (0.5G)
Material Silicone-based (others)
High-concerned chemical None
Origin Mainland China

5. Application Instructions

Before applying new thermal grease, ensure the surfaces of the CPU/GPU and heatsink are clean and free of any old thermal compound or debris. Use isopropyl alcohol and a lint-free cloth for cleaning.

Diagram showing two methods of thermal grease application and four principles of smearing

Image: Visual guide illustrating two application methods and the four principles for effective thermal grease smearing.

  1. Squeeze a small amount of thermal grease (about the size of a pea or rice grain) onto the center of the CPU/GPU surface.
  2. Carefully place the heatsink onto the CPU/GPU. The pressure from the heatsink will evenly spread the thermal grease across the surface.
  3. Gently rotate the heatsink a few degrees back and forth to ensure optimal contact and even spreading.
  4. Secure the heatsink in place according to its manufacturer's instructions.
  1. Squeeze a small amount of thermal grease onto the center of the CPU/GPU surface.
  2. Using a clean, non-conductive coating tool (e.g., a plastic spatula or card edge), gently spread the thermal grease evenly across the entire surface of the CPU/GPU. Aim for a thin, uniform layer.
  3. Ensure there are no air bubbles or gaps in the thermal grease layer.
  4. Carefully place the heatsink onto the CPU/GPU, ensuring it makes full contact.
  5. Secure the heatsink in place according to its manufacturer's instructions.

5.3. The Four Principles of Smearing

  • Apply heat dissipating silicone grease evenly.
  • Apply the heat dissipation silicone grease as thin as possible.
  • The application of heat dissipation silicone grease should be free of impurities.
  • The application of heat dissipation silicone grease should be bubble-free.

6. Maintenance

Thermal grease can degrade over time, losing its effectiveness. It is generally recommended to check and reapply thermal grease every 1-3 years, or whenever you remove the heatsink for cleaning or component upgrades. Always clean off old thermal grease completely before applying new compound.

7. Troubleshooting

7.1. High Temperatures After Application

  • Insufficient or Excessive Thermal Grease: Too little thermal grease can lead to poor contact, while too much can create an insulating layer. Reapply following the instructions carefully.
  • Uneven Application: Air bubbles or uneven spreading can hinder heat transfer. Ensure a thin, even layer.
  • Improper Heatsink Installation: Ensure the heatsink is securely mounted and making full, even contact with the CPU/GPU. Check for any obstructions or loose screws.
  • Old Thermal Grease Not Removed: Residual old thermal grease can interfere with the new compound. Always clean surfaces thoroughly.

8. User Tips

Based on common user experiences:

  • Always clean both the CPU/GPU and heatsink surfaces thoroughly with isopropyl alcohol before applying new thermal grease.
  • A small, pea-sized amount is usually sufficient for most CPUs/GPUs. Less is often more, as long as it covers the entire surface.
  • Consider using a plastic card or spatula for spreading if you prefer a perfectly even layer, especially on larger dies.

9. Warranty and Support

For any questions, technical support, or warranty inquiries, please contact the seller directly through the platform where you purchased this product. Please refer to the official user manual (PDF) for additional details and specific product information, which can be accessed here.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.