OBDMATE OM201

Contents

OBDMATE OM201 OBD2 Scanner User Manual

Model: OM201 | Brand: OBDMATE

Introduction

This manual provides detailed instructions for the operation and maintenance of your OBDMATE OM201 OBD2 Scanner. Please read this manual thoroughly before using the device to ensure proper and safe operation.

OBDMATE OM201 OBD2 Scanner main unit
The OBDMATE OM201 OBD2 Scanner main unit.

Video demonstrating the OM201 OBD2 Code Reader's features including plug-and-play, 10-second diagnostics, reading and erasing codes, live data display, DTC lookup, and report generation.

1. Safety Precautions and Warnings

To avoid injury or damage to the vehicle and/or scan tool, please read this manual at first and observe the following safety precautions when working on a vehicle:

  • Always perform vehicle tests in a safe environment.
  • Do not attempt to operate or observe the unit while driving a vehicle. Operating or observing the device while driving may cause distraction and lead to fatal accidents.
  • Wear safety glasses that meet the standards of ANSI.
  • Keep your hair, hands, clothing, tools, and test equipment away from all moving or hot engine parts.
  • Operate the vehicle in a well-ventilated area: Exhaust fumes are toxic.
  • Place blocks in front of the drive wheels and never leave the vehicle unattended while performing tests.
  • Use extreme caution when working near the ignition coil, distributor cap, ignition wires and spark plugs. These components generate dangerous voltages when the engine is running.
  • Keep a fire extinguisher nearby that is suitable for gasoline, chemical, and electrical fires.
  • Keep the scan tool dry, clean, and free of oil/water or grease. If necessary, use a mild detergent on a clean cloth to clean the outside of the scan tool.

2. General Information

2.1 On-Board Diagnostics (OBD) II

The first generation of on-board diagnostics (called OBD I) was developed by the California Air Resources Board (CARB) and introduced in 1988 to monitor some components of vehicle emission control. With the advancement of technology and the desire to improve the on-board diagnostic system, a new generation of on-board diagnostic system was developed. This second generation on-board diagnostic system is called "OBD II".

The OBD II system is designed to monitor emission control systems and major engine components by performing either continuous or periodic tests of specific components and vehicle conditions. When a problem is detected, the OBD II system turns on a warning light (MIL) on the vehicle's instrument panel to alert the driver, typically with the words "Check Engine" or "Service Engine Soon." The system also stores important information about the detected malfunction so a technician can accurately find and fix the problem. Below are three such valuable pieces of information:

  1. Whether the malfunction indicator lamp (MIL) is set to "On" or "Off";
  2. Whether diagnostic trouble codes (DTCs) are stored and if so, which ones;
  3. Status of the standby monitor.

2.2 Diagnostic Trouble Codes (DTCs)

OBD II Diagnostic Trouble Codes are codes stored by the on-board computer diagnostic system in response to a problem detected in the vehicle. These codes identify a specific problem area and are intended to give you an indication of where a fault may be occurring. OBD II Diagnostic Trouble Codes consist of a five-character alphanumeric code. The first character, a letter, indicates which control system sets the code. The other four characters, all numbers, provide additional information about where the DTC originated and the operating conditions triggered it. Below is an example that illustrates the structure of the digits:

DTC Examples: P0520

Category Description
Systems (1st Character)
  • B = Body
  • C = Chassis
  • P = Powertrain
  • U = Network
Code Type (2nd Character)
  • Generic (SAE): P0, B0, C0, U0
  • Manufacturer Specific: P1, P2, B1, B2, C1, C2, U1, U2
Sub-systems (3rd Character)
  • 1 = Fuel metering and air
  • 2 = Ignition system or engine error
  • 3 = Control of auxiliary emissions
  • 4 = Vehicle speed control and idle controls
  • 5 = Computer output circuits
  • 6 = Transmission controls
Last two digits (4th & 5th Character) Identify the individual component in the system.

Explanation of a diagnostic trouble code structure.

The DLC (Data Link Connector or Diagnostic Link Connector) is the standardized 16-pin connector used to connect diagnostic tools to the vehicle's on-board computer. The DLC is typically located 12 inches from the center of the instrument panel (dashboard), under or on the driver's side of most vehicles. If the DLC is not located under the dashboard, there should be a sticker indicating its location. On some Asian and European vehicles, the DLC is located behind the ashtray and the ashtray must be removed to access the connector. If you cannot find the DLC, check the vehicle's service manual to see where it is.

Diagram showing typical DLC locations in a car interior
The DLC connector is typically located on the driver's side, often under the dashboard.

3. Product Overview

3.1 Tool Description - OM201

Diagram of OM201 tool with labeled parts
The OM201 OBD2 Scanner with its main components labeled.
  1. LCD DISPLAY: Indicates test results. 128x64 pixel backlit monochrome display.
  2. [▲ UP] BUTTON: Scrolls upward through menu items (one item per press).
  3. [ESC] BUTTON: To cancel the current selection/action or to return to the previous menu.
  4. [OK] BUTTON: To confirm the current selection/action.
  5. [▼ DOWN] BUTTON: Scrolls downward through menu items (one item per press).
  6. OBDII CONNECTOR: Connects the scan tool to the vehicle's DLC.

3.2 Specifications

  • Display: 1.77" monochrome LCD with contrast adjustment
  • Operating temperature: 0 to 50°C (32 to 140°F)
  • Storage temperature: -20 to 70°C (-4 to 158°F)
  • External power supply: 8.0 to 18.0 V (Vehicle battery-powered)
  • Dimensions: 132 x 73 x 24 mm (L x W x H)
  • Net Weight: 0.219 kg

3.3 Packing List

  • OM201 - OBDII car diagnostic tool.
  • User manual - Instructions on how to operate the device.

4. Setup and Operation

3.4 Settings

The scan tool allows you to make the following adjustments and settings:

  1. Language: Select your preferred language, then press [OK] to confirm.
  2. Contrast: Press [UP] to increase or [DOWN] to decrease display contrast.
  3. Unit of measurement: Choose between Imperial (e.g., mph, °F) or Metric (e.g., km/h, °C), then press [OK] to confirm.

Main Menu (Example)

Main Menu
Diagnostics
DTC Lookup
►Language
Contrast
Unit of Measure
Print

Navigate to 'Language' in the main menu to change settings.

3.5 DTC Lookup

The DTC Lookup feature enables searching for definitions of fault codes from the built-in code library.

  1. Select DTC Lookup in the main menu, then press [OK] to enter.
  2. To input a fault code, press [OK] + [UP] to move cursor left digit; press [OK] + [DOWN] to move cursor right digit. Then press [UP] or [DOWN] to enter a letter or number.
  3. Press [OK] to make a query.
  4. Press [ESC] key to return to the main menu.

If the code definition is not found (SAE or manufacturer specific), the scan tool will display "DTC definition not found!". In such cases, please consult the vehicle's service manual for further reference.

DTC Lookup Screen (Example)

DTC Lookup

P0001

ENTER+<-Left\Right
[↑][↓]-Change Digit
[ENTER]-Confirm
[EXIT]-Exit

Inputting a DTC for lookup.

3.6 QR-code Diagnostic Report Generation & Printing

This tool supports QR-code based diagnostic report generation and wireless printing. Note: a complete vehicle diagnosis must be performed first.

  1. Select "Print" from the main menu, then press [OK] to enter.
  2. Select the data to print (e.g., Print DTC, Print VIN, Print Live Data, Print Freeze Frame), then press [OK] to enter.
  3. The tool displays a QR code. Scan it with a smartphone. A diagnostic report is automatically generated.
  4. Download the report to your phone's storage for further reference. You can review it at anytime and send the report to a PC for printing. No USB connection required.
OM201 scanner showing QR code for cloud printing and a diagnostic report on a smartphone
Generate and print diagnostic reports wirelessly by scanning the QR code.

4. OBD II Diagnostics

  1. Turn off the ignition.
  2. Plug the scan tool connector into the vehicle's 16-pin DLC.
  3. Turn on the ignition.
  4. Press any button to continue. It will display the device is connecting to the OBDII protocols.
  5. Press [ESC] to enter the main menu. Select "Diagnostics" and press [OK] to start a diagnosis.

Linking to Vehicle (Example)

Linking to vehicle
ISO 9141-2

Waiting for vehicle t
o respond.Press EXIT
to cancel.

The scanner linking to the vehicle's protocol.

Main Menu (Example)

Main Menu
►Diagnostics
DTC Lookup
Language
Contrast
Unit of Measure
Print

Selecting 'Diagnostics' from the main menu.

4.1 Read Codes

  • Stored codes: Also known as "hard codes" or "permanent codes". These codes cause the control module to illuminate the malfunction indicator lamp (MIL) when an emission-related fault occurs.
  • Pending codes: Also known as "mature codes" or "continuous monitor codes". They indicate a problem detected during the current or last driving cycle, but are not considered serious yet. Pending codes will not turn on the malfunction indicator lamp (MIL). These codes will be cleared from memory after several driving cycles if no faults are detected.
  1. From the diagnostic menu, select "Read Codes" and press [OK].
  2. Press [DOWN] to view the next code. Press [ESC] to return to the previous menu.

Diagnostic Menu (Read Codes)

Diagnostic Menu
►Read Codes
Erase Codes
Live Data
View Freeze Frame
I/M Readiness
O2 Sensor Test

Selecting 'Read Codes'.

Read Codes Screen (Example)

P0195 #07E8
Generic
Engine Oil
Temperature Sensor A
Circuit

Example of a read fault code.

4.2 Erase Codes

  1. Select "Erase Codes" from the diagnostic menu.
  2. The screen will prompt "Erase trouble codes! Are you sure?". Select YES and press [OK] to clear the DTCs.
OM201 scanner showing how to erase a check engine light
The OM201 scanner can erase fault codes and turn off the Check Engine Light.

Diagnostic Menu (Erase Codes)

Diagnostic Menu
Read Codes
►Erase Codes
Live Data
View Freeze Frame
I/M Readiness
O2 Sensor Test

Selecting 'Erase Codes'.

Erase Codes Confirmation

Erase Codes
Erase trouble codes!
Are you sure?

YES NO

Confirmation prompt before erasing codes.

Notes:

Before performing this function, be sure to retrieve and record the error codes. After clearing, retrieve the error codes again or turn on the ignition and retrieve the codes again. If there are still error codes in the system, please troubleshoot the codes using factory diagnostic guide, clear the codes and check them again.

4.3 Live Data

Access real-time sensor data from the engine to monitor your car's health.

  1. Select "Live Data" then press [OK] to enter. Select "View All Items" then press [OK] to check all live data.
  2. Press [UP] or [DOWN] keys to scroll through items, or turn the pages. Press [ESC] to return to the previous menu.
  3. To view live data curve, return to the "Live Data" menu first then select "View Graphic Items".
  4. Select the desired item and press [OK] to access its dynamic graph.

Live Data Menu

Live Data
►View All Items
View Graphic Items

Selecting 'View All Items' for live data.

Live Data Display (Example)

DTC_CNT: 0
DTCFRZF: P0000
FUELSYST: N/A
FUELSYS2: N/A
LOAD_PCT(%): 24.3
ECT(°F): 169

Example of live data parameters.

Live Data Graphic Display (Example)

LOAD_PCT(%)
25.5 |
     |   _/
     |  /  \
     | /    \
     |/______\
25.1 +----------

Graphical representation of live data (e.g., Load Percentage).

4.4 View Freeze Frame

When an emission-related error occurs, the ECU automatically records a snapshot of the current vehicle's parameters (Freeze Frame data).

Note: If DTCs have been deleted, the freeze frame data may no longer be available.

  1. Select "View Freeze Frame" from the diagnostic menu.

Diagnostic Menu (Freeze Frame)

Diagnostic Menu
Read Codes
Erase Codes
Live Data
►View Freeze Frame
I/M Readiness
O2 Sensor Test

Selecting 'View Freeze Frame'.

Freeze Frame Display (Example)

Freeze Frame
DTCFRZF: U3FFF

Example of Freeze Frame data.

4.5 I/M Readiness

I/M Readiness is used to test misfire/fuel system/comprehensive components, ensuring your vehicle is ready for emissions testing.

  1. Select "I/M readiness" and press [OK].
  2. Press [UP] or [DOWN] to view more data.

Diagnostic Menu (I/M Readiness)

Diagnostic Menu
Read Codes
Erase Codes
Live Data
View Freeze Frame
►I/M Readiness
O2 Sensor Test

Selecting 'I/M Readiness'.

I/M Readiness Display (Example)

I/M Readiness
►since DTCs Cleared
This Drive Cycle

I/M Readiness status after DTCs cleared.

Since DTCs Cleared (Example)

MIL Status: OFF
Misfire Monitor: N/A
Fuel System Mon: N/A

Detailed I/M Readiness monitor status.

N/A means not available for this vehicle, INC means incomplete or not ready, OK means completed or monitor is ready.

4.6 O2 Sensor Test

OBD II regulations require vehicles to monitor and test oxygen (O2) sensors to detect problems related to fuel efficiency and vehicle emissions. These tests are performed automatically when engine operating conditions are within specified limits, and results are stored in the ECU memory.

The O2 Sensor Test function allows you to retrieve and display the O2 Sensor Monitor test results for the most recently performed tests from the ECU.

Note: The O2 sensor test function is not supported by vehicles that communicate via a Controller Area Network (CAN). The results of the O2 sensor test of vehicles with CAN can be found in the "On-Board Mon. Test".

  1. Select "O2 Sensor Test" in the Diagnostic Menu and press [OK] to enter.
  2. Press [OK], the screen will display the O2 sensor data (data is different each time).

O2 Sensor Test Screen (Example)

O2 Sensor Test
O2 Bank Sensor1
►O2 Bank Sensor2

Selecting O2 sensor bank for testing.

4.7 On-Board Monitor Test

This function enables you to access the results of the on-board diagnostic monitoring.

  1. Select "On-Board Mon. Test" in the diagnostics menu and press [OK].
  2. Use the [UP] or [DOWN] keys to select an item then press [OK]. The screen will then display the data for the selected monitor.
  3. Press [ESC] to return to the previous menu.

On-Board Mon. Test Menu

On-Board Mon. Test
►Test ID $01
Test ID $02
Test ID $04

Selecting a monitor test ID.

Test ID $01 Details (Example)

Test ID $01
Component ID $01
Type: MAX
Test: 0
MIN: ...
MAX: 0
Status: OK

Details for a specific on-board monitor test.

4.8 Vehicle Information

This function displays vehicle information such as VIN (vehicle identification number), CID (calibration number ID), and CVN (calibration check number).

  1. Select "Vehicle Infor" and press [OK] to enter.
  2. Press [ESC] to return to the previous menu.

Vehicle Info Menu

Vehicle Info.
►Vehicle ID Number
Calibration ID
Cal. Verif. Number
Protocol

Selecting 'Vehicle ID Number'.

Vehicle ID Number Display (Example)

Vehicle ID Number
VIN:
123456789ABCDEFGH

Example of a Vehicle Identification Number (VIN).

4.9 Evap Leak Test

The Evap function allows you to initiate a leak test for the vehicle's Evap system. Please note the scanner does not perform the leak test itself, but signals the vehicle's on-board computer to start the test. Before using this function, please refer to the vehicle's repair manual for instructions on how to halt the test.

Select "Evap System Test" and press [OK]. The screen will display the appropriate system information. Please note that some vehicle manufacturers do not allow external devices to control the vehicle system.

If the car supports this function, it will display as below:

Evap Leak Test Screen (Supported)

Evap Leak Test

OK

Press any key to con.

Screen indicating Evap Leak Test is ready.

If the car does not support the function, it will display as below:

Evap Leak Test Screen (Not Supported)

Evap Leak Test

The selected mode is
not supported!

Press any key to con.

Screen indicating Evap Leak Test is not supported by the vehicle.

User Tips

  • For intermittent issues, use the "Freeze Frame" data to capture conditions when the fault occurred.
  • Always ensure the ignition is ON when performing diagnostic tests, unless instructed otherwise.
  • If a code cannot be found in the DTC Lookup, consult your vehicle's specific service manual.
  • Keep the device's software updated for the latest vehicle compatibility and features.

Troubleshooting

"LINKING ERROR!" Message

If the scanner displays "LINKING ERROR!" during connection:

  • Check if the OBDII connector of the tool is firmly connected to the vehicle's DLC.
  • Turn the ignition off and wait for about 10 seconds. Switch the ignition on again and repeat the test.

General Diagnostic Issues

  • No Power: Ensure the OBDII connector is fully seated in the vehicle's DLC. The device is powered by the vehicle's battery (8.0 to 18.0 V).
  • Screen Not Responding: Try pressing the ESC button to return to the main menu. If unresponsive, disconnect and reconnect the device.
  • Incorrect Readings: Verify that the correct unit of measurement (Imperial/Metric) is selected in the settings.

Maintenance

  • Keep the scan tool dry, clean, and free of oil/water or grease.
  • If necessary, use a mild detergent on a clean cloth to clean the outside of the scan tool.
  • Store the device within the specified storage temperature range (-20 to 70°C / -4 to 158°F).

5. Warranty and Support

Warranty Information

  1. This warranty is valid solely for the original purchaser of OBDMATE products.
  2. OBDMATE products are warranted against defects in materials and workmanship under normal use for one year (12 months) from the date of retail purchase.
  3. For any product problems, we commit to providing a resolution within 24 hours.

Contact Information

For support or inquiries, please contact us:

Manufacturer: AUTOPHIX TECH CO.,LTD

Address: Room 406, 403 and 402, Building 2, XiangRong Road No.8, Bujiuwo, Longping Community, Dalang Street, Longhua District, Shenzhen, Guangdong, China. 518000

Certifications: CE, RoHS

Made in: China

A PDF version of this user manual is available for download from the official website or via the QR code generation feature.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.