smardeer L9006-TY-WF

Contents

SmarDeer L9006-TY-WF Smart Lock User Manual

Model: L9006-TY-WF | Brand: SmarDeer

This manual provides essential information for the safe and efficient installation, operation, and maintenance of your SmarDeer L9006-TY-WF Smart Lock.

1. Introduction

The SmarDeer L9006-TY-WF is an advanced outdoor waterproof smart lock designed for enhanced security and convenience. It integrates multiple unlocking methods including 3D facial recognition, palm vein recognition, fingerprint, password, IC card, and mechanical keys. With built-in Tuya WiFi, it offers remote management and real-time video call capabilities. Its IP66 rating ensures durability in various weather conditions.

SmarDeer Smart Lock with 3D Face, Palm, Remote Video Call, IP66 rating
Figure 1.1: SmarDeer Smart Lock highlighting 3D Face, Palm, Remote Video Call, and IP66 rating.
Smart Lock with Fingerprint, Password, IC Card, Emergency Key, 3D Face Recognition
Figure 1.2: Overview of multiple unlocking methods including fingerprint, password, IC card, emergency key, and 3D face recognition.

2. Safety Information

Please read and understand all safety instructions before installation and use. Failure to follow these instructions may result in electric shock, fire, or serious injury.

  • Do not apply excessive force during installation to avoid damaging the lock.
  • Wear protective eyewear when drilling holes to prevent eye injury.
  • Ensure all wiring is correctly connected to prevent malfunction or damage.
  • Keep the lock body and internal components dry.
  • Do not attempt to disassemble the face plate of the lock body.

3. Package Contents

Verify that all components are present and in good condition before beginning installation.

Product package contents including smart lock components, screws, keys, and battery
Figure 3.1: Contents of the SmarDeer Smart Lock package.

Parts List:

No. Part Name Quantity
1Front Panel1
2Studsx2
3Cylinder Screwx2
4Lock Body1
5Indoor Screen1
6Rear Panel1
7Square Rods (12mm)x1
8Screws (12mm)x3
9Latch Box1
10Door Plate1
11Screws (4x10mm, 5 pcs on rear panel)5
12Battery1 (4200mAh)
13Rear Cover Plate1
14Keyx2
15Lock Cylinder1
16Silicone Pad1

4. Specifications

Parameter Specification
Brand Namesmardeer
Model NumberL9006-TY-WF
Power SupplyBuilt-in Rechargeable Battery (4200mAh)
Protection LevelIP66
Suitable for Mortise6068
Installation MethodDrilling installation
Fit Door Thickness40-100mm
Suitable Door TypeSteel Door, Wooden Door, Brass Door, Stainless Steel Door
Special FeaturesBuilt-in Doorbell, Built-in Camera, Built-in Peephole, Built-in Screen, Two-way Audio
Finish TypeOil Rubbed
Doorknob FunctionBiometric, Key & Keypad
ConnectivityWiFi (Tuya Smart home platform)
Ways To UnlockFace Recognition, App, Remote Control, Mechanical Keys, Finger Vein Recognition, CARD, WiFi, Password, FINGERPRINT
MaterialAluminium alloy
Handle DirectionDirection Reversible
Collection Head TypeSelf-learning capacitive press fingerprint head
Fingerprint Resolution508dpi
Rejection Rate (FRR)<0.1%
False Acceptance Rate (FAR)<0.001%
Fingerprint Capacity120 pieces
User Capacity250 sets (100 fingerprints, 100 passwords, 50 faces, 100 cards)
Working Voltage7.0V~8.4V (low voltage alarm at 6.8±0.2V)
Dynamic Power Consumption≤1A (no motor action, no playback sound)
Static Power Consumption≤200uA
Verification Time≤3s
Keyboard TypeTouch sensing
Display Screen0.96 OLED (4.5-inch HD LCD)
Charging Port5V1A Micro USB
Antistatic Ability≥8KV (contact), 15KV (non-contact type)
Storage Temperature-25°C ~ 80°C
Operation Temperature-25°C ~ 70°C
Ambient Humidity15%RH ~ 93%RH
Waterproof Dustproof Design (IP66, -35°C Freeze, 100°C Heat Resistant)
Figure 4.1: The lock's IP66 waterproof and dustproof design, with freeze and heat resistance.
Built-in 4200mAh Lithium Battery
Figure 4.2: The built-in 4200mAh rechargeable lithium battery, offering large capacity, recyclability, and low battery alerts.

5. Installation Guide

5.1. Precautions Before Installation

  • Do not use excessive force during installation.
  • Use appropriate installation tools.
  • Wear safety glasses to protect your eyes when drilling holes.
  • Drill door holes carefully to avoid damaging the door plate.

5.2. Adjusting the Direction of the Lock Body

Adjust the mortise direction according to your door's opening direction:

  1. Pull the latch shift plate upward as shown in the lock body.
  2. Press the latch inward as shown in the diagram.
  3. Rotate the lock latch as shown in the diagram.

Note: Do not disassemble the face plate.

5.3. Installation Steps

  1. Prepare the Lock Body:

    Divide the rear lock into the indoor display screen and rear panel. Unscrew the 5 screws on the rear panel and remove the rear panel cover.

  2. Install the Lock Body:

    Install the lock body using 4 screws. Install the cylinder (keyhole faces outdoors). Use cylinder screws to fix it.

  3. Cut the Lock Cylinder Rod:

    Cut the lock cylinder rod so it protrudes approximately 20mm from the door face.

  4. Install the Front Panel:

    Install 2 studs on the front panel. Install the front panel, ensuring wires and studs are inserted into the corresponding holes.

  5. Install the Silicone Pad:

    Install the silicone pad on the rear panel.

  6. Connect Wires and Rear Panel:

    Connect the wires. Align the holes and install the rear panel (square rod and anti-theft iron piece need to be installed with the lock body). Fix the rear panel with 5 screws.

  7. Install Battery and Indoor Screen:

    Install the battery. Install the indoor screen.

  8. Install Latch Box and Door Plate:

    Install the latch box and door plate, using 4 screws to fix them.

5.4. Check Points After Installation

  • The face plate should be horizontal with the door.
  • The Latch bolt, Dead bolt, and Security Bolt must operate smoothly and flexibly.
  • The Front lock should be vertical and stable.
  • The front handle should operate smoothly and flexibly. The deadbolt should be in position when you lift the handle.
  • The deadbolt should be in position when you lift the back handle, and it should retract when you press the handle.
  • The knob should turn smoothly and flexibly. The security bolt should extend or retract in conjunction with the knob's action.

6. Initial Setup

6.1. Initialization

To factory reset the lock:

  1. Long press the settings button for 5 seconds. The voice will broadcast: "Factory reset, NO(*)YES(#)".
  2. Press the '#' key to confirm. The system will restart to its initial state.

Note: In the initial state, any face, fingerprint, password, or card can unlock the device. Performing a factory reset operation will not clear the set door-opening direction or torque parameters.

6.2. User Settings (Add Administrator Password)

For the first time use, you need to set an administrator password:

  1. Wake up the touch panel.
  2. Press the '*' key.
  3. Voice announcement: "Please enter a 6 to 8 digit password" (enter your desired password).
  4. After successful addition, voice broadcast: "User 000 Add Success".

6.3. Adding Users

After setting the administrator password, you can add other users:

  1. Select "1. Add Admin" or "2. Add User" from the menu.
  2. Follow the prompts to enter the password, fingerprint, or card you want to add.
  3. After successful addition, voice broadcast: "User *** Add Success". You can continue adding users.

For Face Recognition: Position your face parallel to the camera at 30-80cm. Follow voice prompts to complete continuous face recording.

For Fingerprint: Place your finger on the sensor, and the voice prompts "Press again." Repeat to complete continuous fingerprint recording.

For Password: Enter a 6 to 8-digit password and confirm with '#'.

For Card: Bring the card close to the IC card sensing area on the touch keypad. The system will automatically read and save the card information.

Note: Management users (000-009) have 10 digits. Ordinary users (010-249) have 240 characters.

7. Operating Instructions

7.1. Unlocking Methods

Video 7.1: Demonstration of various unlocking methods and waterproof capabilities.

The SmarDeer L9006-TY-WF Smart Lock offers multiple ways to unlock:

  • 3D Face Recognition: The lock uses microwave radar detection and a finance-grade algorithm for anti-photo and anti-video spoofing. Simply present your face for quick and secure access.
  • Palm Vein Recognition: Utilizes near-infrared identification for anti-fake and anti-interference, providing ultra-secure access by scanning your palm vein patterns.
  • Fingerprint: Fast fingerprint recognition with a capacity for 120 unique fingerprints.
  • Password: Enter your registered password on the keypad.
  • IC Card: Swipe your registered IC card over the sensor.
  • Mechanical Key: For emergency situations, use the physical key.
  • Remote Unlock (via Tuya App): Receive remote unlock requests on your mobile phone when visitors ring the doorbell.
3D Face Unlock with Microwave Radar Detection
Figure 7.2: 3D Face Unlock technology with anti-spoofing features.
Palm Vein Unlock with Near-infrared identification
Figure 7.3: Palm Vein Unlock using near-infrared identification for secure access.
Radar Auto-Sensing Face Recognition Unlocking
Figure 7.4: Radar auto-sensing for face recognition unlocking, waking up the lock as you approach.

7.2. Remote Real-Time Video Call

The lock features a built-in camera and two-way audio intercom. When a visitor rings the doorbell, you can:

  • Remotely view visitors via the Tuya App.
  • Make instant video calls and confirm identity.
  • Talk with visitors without opening the door.
  • Use the adaptive broadcast button to talk to the visitor.
  • Slide the release button to the right for remote unlocking.
Remote Real-Time Video Call feature
Figure 7.5: Remote real-time video call functionality via the Tuya App.
4.5-inch HD LCD Screen showing indoor view
Figure 7.6: The 4.5-inch HD LCD screen for direct viewing of outdoor activity.

7.3. Deleting Users

Users can be deleted either by verification or by ID.

7.3.1. Delete by Verification

  1. Select "Delete User" from the menu.
  2. Select "Verify Delete".
  3. Voice announcement: "Please verify the user to be deleted".
  4. Verify the user by fingerprint, password, or IC card.
  5. After successful verification, voice broadcast: "User Delete Success".

7.3.2. Delete by ID

  1. Select "Delete User" from the menu.
  2. Select "Delete by ID".
  3. Voice announcement: "Please enter the user ID to be deleted".
  4. Enter the user ID.
  5. After successful deletion, voice broadcast: "User Delete Success".

7.4. Lock Settings

7.4.1. Tamper Alarm

After activating the anti-tamper alarm, if the door lock is tampered with, the system will issue an alarm prompt: "Illegal user, illegal intrusion, owner notified". If connected to the network, it will push alarm information to your phone.

7.4.2. Motor Torque

Motor torque is specific to the strength of the motor's torque. This setting can be adjusted via the menu.

7.4.3. Lock Back Time

This setting determines the delay before the lock engages after closing.

7.4.4. Dwell Alert

If a human body is detected for a total of 20 seconds within 1 minute, a stay alarm will be triggered. Pushed network devices will not receive sound and light alarms by default.

7.4.5. Face Recognition Settings

You can configure the human sensory function:

  • Off: The intelligent door lock will not engage in human body sensing in standby mode.
  • Intelligence: The intelligent door lock will not engage in human body sensing when the door is opened.
  • Open: In any state, the intelligent door lock will undergo human body sensing.

Note: If there are 10 consecutive awakenings and no facial recognition is detected, human sensing will be turned off by default for 5 minutes.

You can also set the detection distance for face recognition: Near (30-50cm), Medium (50-70cm), Far (70-80cm).

7.5. Network Configuration (Tuya App)

To connect your smart lock to the Tuya App:

  1. Download and sign in to the SmartLife App (available on App Store).
  2. After entering the APP, click "+" in the upper right corner of the home page to add a device.
  3. Enter the "Add Device" page.
  4. For Two-dimensional code distribution network:
    1. Select [Camera & Lock] and click "Video lock (Wi-Fi)".
    2. On the "Reset the device" interface, click Next, check "Scan the QR code with door lock camera", and click [Next].
    3. Select WiFi and enter the password, then click [Next].
    4. After entering the "Reset the device" page, keep waiting for the smart door lock to enter network mode.
    5. Point the QR code on your mobile phone at the camera. When the lock plays a "stomp" prompt tone, click "I Hear a prompt" to enter the distribution state.
  5. For WIFI distribution network:
    1. Select [Camera & Lock] and click "Lock (Wi-Fi)".
    2. Select WIFI and enter the password, then click [Next].
    3. On the "Reset the Device" interface, click Next, select EZMode.

Note: If the power distribution fails, you can select "Switch the power distribution mode" or select the hotspot mode. Connect to the Wi-Fi hotspot starting with SmartLife and configure the network according to the instructions of the mobile phone. Some device hotspot names may be user-defined.

Note: The distribution function only supports one mobile phone for distribution. If you enter the networking configuration again, the last distribution data will be automatically cleared. Users should be cautious when operating.

7.6. Virtual Password

When using a password to unlock, you can add any number before and after the correct password to increase security. For example, if the password is "12346", you can enter "426123456745" to unlock. The system will only recognize the first 16 digits.

7.7. Visitor Mode

In visitor mode, users can generate time-limited passwords (1 to 59 minutes) that become invalid after the set time.

7.8. Renting Mode

In short-term lease mode, users can generate valid passwords for any period. The validity time must be longer than the current time, and the maximum range cannot exceed 60 days. The generated temporary password must be entered within 24 hours after it takes effect, otherwise, it becomes invalid.

7.9. Nanny Mode

In nanny mode, users can set allowable time periods for unlocking daily. The time losing efficacy must be later than the time taking effect. The generated password needs to be input within 24 hours, otherwise it will be invalid.

7.10. Password Management

This function allows you to delete time-limited passwords that are already in effect. It is not possible to delete time-limited passwords that take effect within 24 hours, administrator user's passwords, or standard user's passwords. To invalidate all time-limited passwords, you need to delete User000 on the lock first, and then add it again.

7.11. Record Query

Messages such as doorbell pushes, illegal user attempts, low battery alerts, and unlocking events can be queried in the log.

7.11.1. Inquiry by Order

Sequential query starts with the latest information and goes down. Press the '8' key to search for the next item and the '2' key to search for the previous item.

7.11.2. Inquiry by Time

Enter the time (year, month, day) you want to query.

7.12. Member Management

To manage members:

  1. Click [Member Management] to enter the member management page.
  2. Click [+] in the upper right corner to select other members.
  3. Enter the name of the member to be bound.
  4. On the Member information page, click Manage Unlock Mode.

7.13. Temporary Password

7.13.1. One-Time Password

Select a one-time password and click Add or the '+' sign in the top right corner. Click to obtain the password. The system automatically generates a set of ten-digit password. The password must be used within 6 hours after it is generated and can only be used once.

7.13.2. Unlimited Password

Select an unlimited password and click Add or the '+' sign in the top right corner. Select effective time and implementation time. Click to obtain the password. The system automatically generates a set of ten-digit password.

7.14. Version Number

Enter '999#' to read the system version number.

8. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the lock's surface. Avoid abrasive cleaners or solvents that could damage the finish or electronic components.
  • Battery Care: The lock has a built-in 4200mAh rechargeable lithium battery. Charge it promptly when the low battery warning is issued. Use the provided USB charging cable.
  • Waterproof Integrity: While the lock is IP66 rated, avoid prolonged submersion or direct high-pressure water jets. Ensure all seals are intact after any maintenance.
  • Mechanical Components: Periodically check the latch, deadbolt, and handle for smooth operation. If any stiffness is observed, consult the troubleshooting section or contact support.
  • Software Updates: Keep the Tuya App updated to ensure optimal performance and access to the latest features.

9. Troubleshooting

Q: The lock is not responding.
A: Check the battery level. If the battery is low, charge it using the external USB emergency power supply. Ensure the lock is properly installed and all connections are secure.
Q: Low battery warning is constantly active.
A: The system will voice prompt "Low power" when the battery level is less than 25%. The lock can still be unlocked about 50 times. Charge or replace the battery promptly.
Q: Failed to unlock after multiple attempts.
A: If unlocking fails after 3 to 5 consecutive inputs, the system will broadcast "Illegal user, illegal intrusion, owner notified" and lock for 90 seconds. Wait for 90 seconds before trying again. Ensure correct credentials (face, fingerprint, password, card) are used.
Q: The lock does not detect human presence for face recognition.
A: Check the face recognition settings (Human body sensing). Ensure it is set to 'Intelligence' or 'Open'. If there are 10 consecutive awakenings without facial recognition, human sensing will be turned off for 5 minutes; reactivate it in settings.
Q: Cannot connect the lock to the Tuya App.
A: Ensure your Wi-Fi network is 2.4GHz (5GHz is not supported). Verify the Wi-Fi password. If connection fails, try switching the power distribution mode or using hotspot mode as described in the APP Operation section.
Q: The generated temporary password is not working.
A: Temporary passwords must be used within 24 hours of generation (for renting mode) or 6 hours (for one-time password). Ensure the password is entered correctly, including any virtual password digits.

10. User Tips

  • Regular Charging: Even with long battery life, it's good practice to charge the lock regularly, especially if you frequently use features like video calls or remote access.
  • Multiple Unlock Methods: Set up multiple unlock methods (fingerprint, password, card) for all users as a backup in case one method is inconvenient or fails.
  • Virtual Password: Utilize the virtual password feature for added security when entering your password in public.
  • App Notifications: Enable notifications in the Tuya App to receive real-time alerts for low battery, illegal entry attempts, or doorbell rings.
  • Door Compatibility: Before installation, double-check your door thickness and mortise type to ensure compatibility with the lock.

11. Warranty and Support

For detailed warranty information and technical support, please refer to the official SmarDeer website or contact your retailer. Keep your purchase receipt as proof of purchase.

A user manual in PDF format is available for download: SmarDeer L9006-TY-WF User Manual (PDF).

© 2024 SmarDeer. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.