Amagi LED lamp

Contents

Amagi Wireless Car Bat Logo Door Decor Light User Manual

Model: LED lamp

1. Introduction

Thank you for choosing the Amagi Wireless Car Bat Logo Door Decor Light. This device projects a distinctive bat logo onto the ground when your car door is opened, providing both a unique aesthetic and a welcome light. This manual provides essential information for the safe and effective use of your new projector light.

2. Safety Information & Precautions

  • Inspect the unit for any damage before installation and use. Do not use if damaged.
  • Avoid dropping the unit, as this may damage internal components.
  • Keep out of reach of children. This product is not a toy.
  • Do not expose the unit to extreme temperatures or direct water immersion.
  • Ensure correct battery polarity when installing batteries.

3. Package Contents

  • Wireless Car Bat Logo Door Decor Light unit(s)
  • Adhesive pads
  • Small magnet(s)

Note: 3 x AAA batteries are required per unit and are not included.

Two projector units with adhesive pads and magnets

Image: Package contents showing two projector units, adhesive pads, and magnets.

4. Setup and Installation

4.1. Battery Installation

  1. Gently open the battery compartment cover on the back of the projector unit.
  2. Insert 3 AAA batteries, ensuring correct polarity (+/-) as indicated inside the compartment.
  3. Close the battery compartment cover securely.
Projector unit with open battery compartment

Image: Projector unit with its battery cover open, showing the compartment for three AAA batteries.

4.2. Mounting the Projector Light

Follow these steps carefully for optimal performance:

  1. Clean Installation Location: Thoroughly clean and dry the desired installation area on the car door panel and the corresponding area on the door sill/frame where the magnet will be placed. Ensure the surface is free of dust, grease, or moisture.
  2. Test Induction Distance: Hold the projector unit in your hand and bring the small magnet close to its sensor area (usually marked). The light should turn off when the magnet is close (5mm-10mm) and turn on when the magnet is moved away. This confirms the sensor is working.
  3. Temporary Placement Test: Before permanent adhesion, use temporary tape (like sellotape) to fix the projector light to the desired spot on the car door. Close and open the door to test if the light activates correctly (turns on when door opens, off when door closes). Adjust the position of the light and the magnet until the desired effect is achieved.
  4. Permanent Adhesion: Once the optimal position is confirmed, remove the backing from the adhesive pad on the projector unit and firmly press it onto the car door. Similarly, remove the backing from the magnet's adhesive pad and firmly press it onto the door sill/frame, aligning it with the projector's sensor when the door is closed.
Four-panel image detailing the installation steps for the door projector light

Image: Step-by-step installation guide for the door projector light.

Car door open, showing the projected bat logo on the ground

Image: The projector light in action, displaying the bat logo on the ground when the car door is open.

5. Operating Instructions

The Amagi Wireless Car Bat Logo Door Decor Light operates automatically. Once installed and powered with batteries, it will:

  • Turn On: When the car door is opened, the magnet moves away from the projector's sensor, activating the LED light and projecting the bat logo onto the ground.
  • Turn Off: When the car door is closed, the magnet comes into proximity with the projector's sensor, deactivating the LED light.
Clear image of the projected blue bat logo on a surface

Image: A clear view of the projected blue bat logo.

6. Maintenance

  • Cleaning: Wipe the exterior of the unit with a soft, dry cloth. Do not use abrasive cleaners or solvents.
  • Battery Replacement: When the projection becomes dim or the light stops working, replace all three AAA batteries with new ones. Refer to Section 4.1 for battery installation steps.
  • Adhesive Reapplication: If the unit or magnet becomes loose, clean the surfaces thoroughly and reapply with new strong double-sided adhesive tape.

7. Troubleshooting

ProblemPossible CauseSolution
Light does not turn on.Dead or incorrectly installed batteries. Sensor not detecting door opening.Replace batteries, ensuring correct polarity. Check alignment of projector and magnet; ensure magnet moves far enough away from sensor.
Projection is dim or flickers.Low battery power.Replace all three AAA batteries with new ones.
Light stays on or off constantly.Magnet is too close/far from the sensor. Sensor malfunction.Adjust the position of the magnet relative to the projector's sensor. If problem persists, contact support.
Unit falls off the door.Improper surface preparation or weak adhesive.Clean the surface thoroughly with alcohol and reapply with new, strong double-sided adhesive tape.

8. Specifications

FeatureSpecification
Model NameLED lamp
Item TypeAtmosphere lamp
Lamp TypeLED
Power1W
Voltage5V
Power SourceDRY BATTERY (3 x AAA, not included)
Material TypePlastic
Luminous Flux>82000
Is Bulbs IncludedNo
Size (Approx.)6.5cm x 6.3cm / 2.56" x 2.48"
CertificationCE
OriginMainland China

9. User Tips

  • Always clean the installation surface thoroughly with an alcohol wipe and let it dry completely before applying the adhesive for maximum hold.
  • Test the light's function and placement with temporary tape before committing to the permanent adhesive. This allows for adjustments to achieve the perfect projection angle and sensor activation.
  • Consider using high-quality alkaline AAA batteries for longer-lasting performance and brighter projection.

10. Warranty and Support

For any issues not covered in this manual, or for warranty inquiries, please contact the seller or manufacturer's after-sales service directly. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.