Introduction
Thank you for choosing BAOFENG! The BF-88E is an FM two-way radio transceiver designed for use in the 446 private mobile radio service (PMR446). This service is license-exempt, but usage restrictions may apply in some Non-EU countries. For further information, please refer to the "Restrictions on the use" section.
Combining the latest technology in radio communication with a sturdy mechanical frame, the BF-88E is an ideal and effective solution for professionals needing to stay in touch with their working team (e.g., construction sites, buildings, trade fairs, hotels) or for leisure users who want to communicate with friends and family.
RF Energy Exposure and Product Safety Guide
ATTENTION!
Before using this product, please read the RF Energy Exposure and Product Safety Guide that ships with the radio. This guide contains instructions for safe usage, RF energy awareness, and control for compliance with applicable standards and regulations.
Any attempt to change frequencies or output power of the radio invalidates the approval.
Package Contents
Your BF-88E package should contain the following items:
- 2 BF-88E transceivers
- 2 1500mAh Li-ion rechargeable battery packs
- 2 belt clips
- 2 desktop chargers
Image: Baofeng BF-88E walkie-talkie highlighting 5W power, PMR446 frequency, 16 channels, and 1500mAh battery capacity.
Product Overview and Main Controls
Familiarize yourself with the main controls and parts of your BF-88E radio:
Diagram: Front and side views of the BF-88E radio, indicating the location of its components.
- Antenna
- Encoder: Rotate clockwise or counter-clockwise to select the desired channel.
- Power/Volume Knob: Turn clockwise to power on and increase volume. Turn counter-clockwise to decrease volume and power off.
- Speaker
- Built-in Microphone
- LED Indicator: RED for Transmit (TX); GREEN for Receive (RX).
- PTT (Push-To-Talk) Button: Press to transmit, release to receive.
- Side Key 1: Hold down to activate the Monitor function.
- Side Key 2: Short press to turn on/off the flashlight.
- External Speaker/Mic Jack: Allows connection of external devices such as headsets or microphones.
- Flashlight
Setup
Battery Installation and Charging
The BF-88E uses a 3.7V Li-ion rechargeable battery pack. To charge the battery:
- Connect the AC/DC wall adapter to a mains power socket.
- Insert the jack of the wall adapter into the desktop charger plug.
- Place the radio with the battery pack into the desktop charger.
A full recharge typically takes 4-5 hours. For maximum battery life, it is recommended to charge the battery pack when the BF-88E is off and the battery is fully discharged.
Warning: Using a different battery charger other than the one specified can cause damage to your device or may even cause explosions and personal injuries.
Image: The BF-88E can be charged via its USB desktop charger using various power sources like car chargers, laptops, or power banks.
Operation
Power On/Off and Volume Adjustment
- To power on: Rotate the Power/Volume knob (3) clockwise.
- To adjust volume: Continue rotating the knob clockwise to increase volume, or counter-clockwise to decrease it.
- To power off: Rotate the knob counter-clockwise until you hear a mechanical "click".
Transmission
To communicate, all radios in your group must be set to the same channel. Radio communication allows only one user to talk at a time. Therefore, avoid transmitting when receiving a communication and use the transmission mode sparingly to allow other users to talk. Transmission consumes significant battery energy.
- Before transmitting, briefly press Side Key 1 (8) to activate the Monitor function and ensure the frequency is not busy.
- Press the PTT button (7) to transmit.
- Release the PTT button (7) to receive.
Monitor Function
The Monitor function opens the Squelch to allow listening to signals that are too weak to keep the Squelch permanently open. Hold down Side Key 1 (8) to enable this function.
Scan Function
This function can only be activated via optional programming software. To enable Scan, all 16 channels must be programmed. If you turn on the radio on channel 16, scanning will automatically start. When a signal is detected, scanning will stop on the busy channel. If the PTT is pressed, you will transmit on the latest busy channel. Channel 16 is the priority channel; if no signal is detected when PTT is pressed, the radio will transmit on channel 16.
Squelch
The Squelch function suppresses noise on free channels and allows reception of even weak signals. The BF-88E has 10 different Squelch levels (0-9) configurable via programming software:
- Level 0: Squelch is turned off.
- Levels 1-9: Different levels of noise reduction. Higher levels provide stronger noise reduction.
By default, the Squelch level is set to 4. Avoid setting an excessively high Squelch level, as this may prevent reception of weaker signals. Conversely, an excessively low Squelch value might enable the Squelch even when no signals are present. Squelch should always be adjusted when no signals are present.
The Time Out Timer (TOT) is settable from 30 to 270 seconds via programming software. This feature is disabled by default.
CTCSS/DCS Tones
CTCSS and DCS tones act as access codes, allowing the radio to communicate only with users tuned to the same channel and using the same code. For each channel, you can set up to 50 CTCSS tones and 210 DCS codes. This ensures that undesired signals from other stations on the same frequency but with different CTCSS/DCS tones are not received.
Flashlight
With the BF-88E turned on, short press Side Key 2 (9) to turn the flashlight (11) on or off.
Emergency Alert Function
If needed, Side Key 1 (8) can be pre-programmed as an Alarm function via CPS programming software. To activate the alarm, short press Side Key 1. Press it again to release the emergency alarm status.
CPS programming path: Edit > Function Setting > Side Key > Alarm
User Tips
- Battery Life: To maximize battery life, ensure the radio is off and the battery is fully discharged before recharging. The power saving feature, which reduces consumption by up to 50% after 5 seconds of no signal, can be enabled via programming software.
- Clear Communication: Always check if a channel is clear using the Monitor function before transmitting to avoid interruptions.
- Interference Reduction: Utilize CTCSS/DCS subchannels to maintain private and stable conversations by filtering out unwanted signals.
- Squelch Adjustment: Adjust the Squelch level carefully. A level too high might block weak but important signals, while a level too low might pick up excessive background noise. Adjust it when no signals are present.
Maintenance
To ensure your BF-88E provides many years of reliable service, please follow these suggestions:
- Do not attempt to open the unit. Improper handling can damage the unit and void the warranty.
- When using a regulated power supply, ensure the voltage is 5V to prevent damage.
- Avoid exposing the radio to high temperatures, which can shorten the life of electronic devices and deform plastics.
- Do not store the radio in dusty or dirty areas.
- Keep the radio dry. Rainwater or dampness will corrode electronic circuits.
- If you notice a peculiar smell or smoke coming from the radio, immediately shut it off and remove the charger or battery.
- Do not transmit without an antenna.
Troubleshooting
If you encounter issues with your BF-88E, consider the following:
- No Power: Ensure the battery is fully charged and correctly installed. Check that the Power/Volume knob is turned clockwise past the "click" to power on.
- Cannot Transmit or Receive: Verify that your radio and the other party's radio are on the same channel and using the same CTCSS/DCS tones (if enabled). Check that the antenna is securely attached.
- Poor Audio Quality/Excessive Noise: Adjust the Squelch level. If the Squelch is too high, it might block weak signals. If too low, it might pick up background noise. Ensure the microphone and speaker are clear of obstructions.
- Short Battery Life: Ensure the battery is fully charged before use. Consider enabling the power saving feature via programming software.
- Radio Malfunction: If the radio emits smoke or a strange smell, immediately power it off, disconnect the charger, and remove the battery. Do not attempt to repair it yourself.
Technical Specifications
| Feature | Specification |
|---|---|
| General Part | |
| Frequency Range | 446.00625-446.19375 MHz (PMR446) |
| Channels | 16 PMR446 (8+8 preprogrammed) |
| Working Temperature | -10°C to +40°C |
| Operation Voltage | DC 3.7 V ±10% |
| Operation Mode | Simplex |
| Dimensions | 170(L) x 55(W) x 35(H)mm (without Antenna) |
| Weight | 150g (Battery pack included) |
| Antenna Impedance | 50ohm |
| Category | B |
| Transmitter Part | |
| Frequency Stability | ±2.5ppm |
| RF Output Power | ≤500mW ERP |
| Max Frequency Deviation | ≤2.5KHz |
| Audio Distortion | ≤3% |
| Adjacent Channel Power | < 60dB |
| Spurious Radiation | Within European legal terms |
| Occupied Bandwidth | Within European legal terms |
| Receiver Part | |
| Receive Sensitivity | < 0.2µV @20dB SINAD |
| Audio Distortion | ≤3% |
| Audio Response | 300 Hz ~ 3 KHz |
| Adjacent Channel Selectivity | Within European legal terms |
| Inter Modulation Rejection | Within European legal terms |
| Spurious Response | Within European legal terms |
| Blocking | Within European legal terms |
Frequency Chart
| Ch. | Freq. (MHz) | Ch. | Freq. (MHz) | Ch. | Freq. (MHz) | Ch. | Freq. (MHz) |
|---|---|---|---|---|---|---|---|
| 1 | 446.00625 | 5 | 446.05625 | 9 | 446.10625 | 13 | 446.15625 |
| 2 | 446.01875 | 6 | 446.06875 | 10 | 446.11875 | 14 | 446.16875 |
| 3 | 446.03125 | 7 | 446.08125 | 11 | 446.13125 | 15 | 446.18125 |
| 4 | 446.04375 | 8 | 446.09375 | 12 | 446.14375 | 16 | 446.19375 |
Warranty and Support
Disclaimer
The accuracy and completeness of the contents of this manual are diligently sought during compilation. However, we do not bear responsibility for possible errors or omissions. Due to continuous technological development, we reserve the right to change the design and specifications of the product without prior notice. No part of this handbook may be copied, modified, translated, or disseminated in any form without the prior written authorization of our department.
EU Declaration of Conformity
Baofeng and Pofung declare that the radio equipment type listed in the Technical Specifications is in compliance with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following link: User manual (PDF).
For support, you may contact your local Baofeng helpdesk, the dealer from whom you purchased this radio, or send an email to wangjianhui@baofengradio.com.
This product is an FM two-way radio transceiver suitable for use in the 446 private mobile radio service (PMR446). This is a license-exempt service, but restrictions of use may apply in some Non-EU countries.
EU Contact: APEX CE SPECIALISTS LIMITED, Unit 3D North Point House, North Point Business Park, New Mallow Road, Cork, T23 AT2P, Ireland
Manufacturer: PO FUNG ELECTRONIC (HK) INTERNATIONAL GROUP COMPANY LIMITED, Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong. Website: http://www.baofengradio.com
Product Disposal Information (WEEE)
All articles displaying the crossed-out wheeled bin symbol on the body, packaging, or instruction manual must not be disposed of in normal waste bins. Instead, they must be taken to specialized waste disposal centers. Here, the various materials will be separated based on their characteristics and recycled, making an important contribution to environmental protection.
This is in accordance with Directive 2002/95/CE, 2002/96/CE, and 2003/108/CE regarding the reduction of hazardous substances in electrical and electronic equipment and waste disposal.