Introduction
Thank you for choosing the EightFox Car Rear View Camera. This manual provides essential information for the safe installation, operation, and maintenance of your new camera system. Please read this manual thoroughly before installation and keep it for future reference.
Safety Precautions
[WARNING] Before installation, ensure the engine is turned off and disconnect the negative (-) terminal of the car battery to prevent short circuits or electric shock.
- Ensure all connections are secure and properly insulated to prevent electrical shorts.
- Do not obstruct the driver's view or interfere with vehicle safety systems during installation.
- If you are unsure about any part of the installation, seek professional assistance.
Setup and Installation
Package Contents
Please check the package for the following items:
- Rear View Camera Unit
- Video Cable (6 meters)
- Power Cable
Image: Overview of the camera unit, video cable, and power cable.
Wiring Diagram and Installation Steps
Follow the diagram below for proper wiring and installation. A monitor/head unit is not included.
Image: Detailed wiring diagram showing connections to the head unit, reversing light, and camera.
- Connect Video Input: Connect the yellow RCA plug from the camera's video cable to the navigation video input plug (usually labeled 'Rear View Camera Input' or 'Video In').
- Connect Reverse Detection Line: Connect the red trigger wire (often labeled 'BACK' or 'REVERSE') from the video cable to your head unit's reverse detection line.
- Power Connection: Connect the camera's power cable. The red wire connects to the positive (+) pole of the vehicle's reversing light. The black wire connects to a ground point (negative (-) pole of the reversing light or vehicle chassis).
- Camera Mounting: Mount the camera securely in the designated location (e.g., near the license plate light).
Conversion Line Control
Your camera features control wires to adjust its functionality. These wires are typically found near the camera's power input.
Image: Diagram showing the brown, green, and white control wires and their functions.
- Brown Cable: Signal control (used for switching video signal type).
- Green Cable: Parking line control (cut to enable/disable parking lines).
- White Cable: Mirror control (cut to switch between rear view and front view/mirror image).
Image: Visual representation of cutting wires to switch parking lines on/off and between AHD/CVBS signals.
Image: Diagram showing the white wire for mirror control (rear to front view).
Video Signal Type Configuration (AHD/CVBS)
Your camera supports both AHD (Analog High Definition) and CVBS (Composite Video Broadcast Signal) video outputs. Ensure your head unit is set to the correct signal type.
For AHD Displays:
If your Android head unit supports AHD, you may need to configure it:
- Go to your Car settings.
- Navigate to Factory settings.
- Find Reverse (picture) settings.
- Select AHD 1080P or AHD 720P depending on your camera model and head unit capability.
Image: Screenshot of an Android head unit's 'BackCar Setting' menu showing AHD options.
Note: If AHD options cannot be selected, your head unit may not support AHD cameras.
For CVBS Displays:
CVBS cameras are compatible with a wider range of displays, including older 4.3-inch, 5-inch, 7-inch, 9-inch screens, and old-style navigation DVDs.
Image: Various types of display screens compatible with CVBS cameras.
To set your Android head unit for CVBS:
- Go to your Car settings.
- Navigate to Factory settings.
- Find Reverse (picture) settings.
- Select CVBS NTSC.
Image: Screenshot of an Android head unit's 'BackCar Setting' menu showing CVBS-NTSC option.
Operating Instructions
Once properly installed and configured, the rear view camera system will automatically activate and display the rear view on your monitor when the vehicle is shifted into reverse gear.
Dynamic Trajectory Guidelines
Some camera models feature dynamic trajectory guidelines that adjust automatically based on the car's steering wheel position and direction.
Image: Visual explanation of dynamic trajectory lines adjusting for left, straight, and right turns.
- The trajectory guideline adjusts itself automatically according to the moving position and speed of the car body and direction instead of steering wheel control.
- If you need to cancel the trajectory line, please cut the white control line.
Parking Line Switch
To enable or disable static parking lines, cut the green control line.
Mirror Control (Front/Rear View)
To switch between a mirrored rear view and a non-mirrored front view (if applicable), cut the white control line.
Maintenance
- Cleaning the Lens: Regularly clean the camera lens with a soft, damp cloth. Avoid abrasive cleaners that could scratch the lens.
- Checking Connections: Periodically check all wiring connections to ensure they are secure and free from corrosion.
- Waterproof Rating: The camera is IP68 waterproof, meaning it is protected against dust and can withstand immersion in water up to 1 meter for 30 minutes. However, avoid high-pressure washing directly on the camera.
Image: Demonstration of the camera submerged in water, highlighting its IP68 waterproof rating.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No image on screen | No power to camera; Loose video connection; Incorrect video input selected on head unit; Incorrect video signal type (AHD/CVBS) selected. | Check power connections to camera and reversing light; Ensure video cable is securely connected; Select correct video input on head unit; Verify head unit is set to AHD or CVBS as per camera type. |
| Flickering or distorted image | Unstable power supply; Poor ground connection; Electrical interference. | Ensure stable 12V power; Check ground connection for tightness and cleanliness; Reroute cables away from other electrical wires if possible. |
| Parking lines not appearing/incorrect | Green control wire not cut/cut incorrectly; Camera angle is off; Dynamic trajectory not functioning. | Check the status of the green control wire; Adjust camera mounting angle; If dynamic trajectory is desired, ensure the white control wire is intact. |
| Image is reversed (mirror image) | White control wire not cut/cut incorrectly. | Check the status of the white control wire to toggle mirror image. |
Specifications
| Brand Name | EightFox |
| Lens Material | Glass |
| Shell Material | Plastic |
| Material | ABS |
| Viewing Angle | 170° (some models 150°) |
| Guiding Line | Yes (Static or Dynamic Trajectory, configurable) |
| Alarm Type | Rear Side |
| Video Signal | AHD (720P/1080P) / CVBS (NTSC) |
| Video Pixel | AHD 1280*720P, AHD 1920*1080P (model dependent) |
| Waterproof Rating | IP68 |
| Length of Video Cable | 6M |
| Certification | CE |
| Origin | Mainland China |
| Package Dimensions | 17cm (L) x 9cm (W) x 5cm (H) |
| Package Weight | 0.2 kg |
Image: Table comparing specifications across different camera models (720P/1080P, CCD, angles, parking lines, waterproof, etc.).
User Tips
- Test Before Final Installation: It is highly recommended to connect and test the camera system with your head unit before fully routing and securing all cables. This helps identify any issues early.
- Secure Grounding: A clean and secure ground connection is crucial for stable video output and to prevent electrical interference.
- Optimal Angle: Experiment with the camera's mounting angle to achieve the best possible view of your vehicle's rear surroundings.
Warranty and Support
For warranty information, technical support, or any questions not covered in this manual, please contact the seller directly. You may also refer to the official user manual PDF for additional details: View User Manual (PDF).