MAGIC COLORM 8J0945097

Contents

User Manual

Third Brake Light for Audi MK2 TT 8J (2007-2014)

Brand: MAGIC COLORM | Model: 8J0945097

1. Introduction

This manual provides essential information for the safe and effective installation, operation, and maintenance of your new Third Brake Light for Audi MK2 TT 8J (2007-2014). Please read all instructions carefully before use.

Third brake light installed on an Audi TT rear, showing illumination.

Figure 1: Third Brake Light installed on an Audi TT.

2. Important Safety Information

Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

  • Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture during installation or if not properly sealed.

3. Package Contents

Please verify that all components are present and undamaged:

  • 1 x Third Brake Light Assembly (Red)
  • Installation hardware (pre-attached or included)
Top view of the red third brake light assembly.

Figure 2: Included Third Brake Light Assembly.

4. Specifications

Attribute Value
Product Name Tail Light (Third Brake Light)
Model Number 8J0945097
Compatibility Audi MK2 TT 8J (2007-2014)
Light Source LED
Color Red
Voltage 12V
Material ABS Housing + Polycarbonate Lens
Waterproof Rating IP67
Installation Direct Plug & Play
Certifications CCC, Dot, ECE
Dimensions (Approx.) Length: 45.2 cm (17.8"), Height: 3.1 cm (1.22")
Product dimensions showing length and height.

Figure 3: Product Dimensions.

5. Installation Instructions

Step 1: Preparation Work (Safety First)

  1. Park the car steadily and engage the handbrake.
  2. Disconnect the negative cable of the battery to prevent electrical hazards.

Step 2: Remove the Old Light

  1. Open the tailgate.
  2. Locate and remove the tail light repair cover from the inside of the vehicle.
  3. Disconnect the electrical plug from the old light.
  4. Unscrew any fixing nuts holding the old light in place.
  5. Carefully pull out the old lamp from the outside to the inside.

Step 3: Install the New Light (Test First, Then Fix)

  1. Pre-testing: First, connect the new light's plug to the original car harness.
  2. Reconnect the battery.
  3. Turn on the power and test whether the brake lights, turn signals, reverse lights, and driving lights are all lit up normally.
  4. Formal Installation: After confirming that the function is normal, disconnect the battery again.
  5. Align the new light with its designated position and install it.
  6. Tighten all the fixing nuts from the inside.
  7. Finally, tighten the electrical plug and replace the maintenance cover.
Diagram showing the plug-and-play connector for easy installation.

Figure 4: Plug-and-Play Connector.

Before and after installation comparison of the brake light.

Figure 5: Installation Effect (Before & After).

6. Operating Instructions

Final Inspection:

  1. Reconnect the battery.
  2. Check all lighting functions (brake lights, turn signals, reverse lights, driving lights) once more to ensure they are operating correctly.

Video 1: Product demonstration showing the light in operation.

7. Maintenance

Sealing Inspection:

  • After washing the car or after heavy rain, check whether there is any severe water ingress or fogging inside the lamp.
  • Slight fogging is normal and should clear up and dry naturally. If severe water ingress persists, re-check the installation and sealing.
Image illustrating the waterproof capabilities of the brake light in various weather conditions.

Figure 6: Waterproof feature for various weather conditions.

8. Troubleshooting

If you encounter any issues with your Third Brake Light, please refer to the following common problems and solutions:

  • Light not illuminating: Ensure the electrical plug is securely connected and the battery is properly reconnected. Check the vehicle's fuse box for any blown fuses related to the brake lights.
  • Intermittent operation: Verify all connections are tight and free from corrosion. Ensure the wiring harness is not pinched or damaged.
  • Water inside the lens: If severe water ingress occurs (beyond slight fogging that clears), re-check the installation for proper seating and sealing. Ensure all nuts are tightened correctly.
  • Incorrect fitment: Double-check that the product is indeed compatible with your Audi MK2 TT 8J (2007-2014) model.

If the problem persists after following these steps, please contact customer support.

9. User Tips

  • Always perform a functional test of the light before fully securing it to ensure proper operation.
  • When disconnecting and reconnecting the battery, ensure your vehicle's radio code (if applicable) is available to avoid lockout.
  • Consider applying a thin bead of automotive-grade silicone sealant around the edges of the light assembly during installation for an extra layer of moisture protection, especially in harsh climates.

10. Warranty & Support

For any issues such as product damage, mismatch, or missing parts, please contact the Shengda Car Light Store customer service. They will provide a satisfactory solution.

After-sales Guarantee Guide: Product Damage, Mismatch, Missing Parts. Contact customer service for a solution.

Figure 7: After-sales Guarantee Guide.

You can also refer to the official user manual PDF for additional details: View User Manual (PDF)

11. Compliance Information

Manufacturer: Guangzhou Camel Technology Co., Ltd. No.4 West Fangxin Road, Fangcun Avenue, Liwan District, Guangzhou City, Guangdong Province.

EU Authorized Representative: MJCM SAR, 78 Avenue des Champs Elysees Office 326, Paris, France. Contact: mjcm190928@gmail.com, 0033 752907452.

Importer: Guangzhou Camel Technology Co., Ltd. No.4 West Fangxin Road, Fangcun Avenue, Liwan District, Guangzhou City, Guangdong Province.

Attestation of Compliance:

  • Applicant: Foshan Hulyou Lighting Co., Ltd.
  • Address: One of No.97 Hainanzhou Industrial Zone, Caochang Lishu Town, Hainan District Foshan City.
  • Product: LED Strip Lighting
  • Model No.: N002 (Note: This model number may refer to the LED strip component, not the full assembly.)
  • Trademark: N/A
  • Report Number: HUT20026631-2ZE HUT
  • Issued Date: Apr. 08, 2021
  • CE Authorized Signer: IrehHUT
Attestation of Compliance certificate for LED Strip Lighting.

Figure 8: Attestation of Compliance.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.