MAGIC COLORM 8K5945097 / 8K5945097A

Contents

LED Third Brake Light for Audi A4 B8 S4 Saloon

Model: 8K5945097 / 8K5945097A

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your new MAGIC COLORM LED Third Brake Light. Please read this manual thoroughly before installation and use to ensure proper function and safety.

LED Third Brake Light installed on an Audi A4 B8 S4 Saloon

Image: LED Third Brake Light installed on an Audi A4 B8 S4 Saloon, showcasing its appearance.

2. Safety & Warnings

Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

  • Warning: Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture unnecessarily.

3. Specifications

FeatureDescription
FunctionSafety Warning (Third Brake Light)
Light SourceHigh Brightness LED
ColorRed (with red lens)
Working Voltage12V DC
OEM Reference8K5945097 / 8K5945097A
MaterialABS Housing + PC Lens
Waterproof RatingIP67
InstallationDirect Plug & Play Replacement
CertificationCCC, Dot, ECE
Special FeaturesWaterproof
DimensionsLength: 35 cm (13.78 in), Height: 11.5 cm (4.53 in)
Package Weight0.5 kg
Product details showing PC lens, bright light, and ABS housing

Image: Product details highlighting the PC lens, bright LED light, and durable ABS housing.

Diagram showing product dimensions: 35cm length and 11.5cm height

Image: Diagram illustrating the product's dimensions (Length: 35cm, Height: 11.5cm).

4. Setup (Installation)

4.1. Preparation Work (Safety First)

  1. Park the car steadily and engage the handbrake.
  2. Important: Disconnect the negative cable of the battery to prevent electrical hazards.

4.2. Removing the Old Light

  1. Open the tailgate of your Audi A4 B8 S4 Saloon.
  2. Locate and remove the tail light repair cover from the inside of the vehicle.
  3. Disconnect the electrical plug from the old light.
  4. Unscrew any fixing nuts holding the old light in place.
  5. Carefully pull out the old lamp from the outside to the inside of the vehicle.

4.3. Installing the New Light (Test First, Then Fix)

  1. Pre-testing: First, connect the new light's plug to the original car harness.
  2. Reconnect the negative battery cable.
  3. Turn on the vehicle's power and test whether the brake lights, turn signals, reverse lights, and driving lights are all lit up normally.
  4. Formal Installation: After confirming that the function is normal, disconnect the battery again.
  5. Align the new light with its designated position and carefully install it.
  6. Tighten all the fixing nuts from the inside to secure the light.
  7. Finally, tighten the electrical plug and replace the maintenance cover.
Close-up of the plug-and-play connector for easy installation

Image: Close-up of the plug-and-play connector, illustrating the ease of installation.

Before and after comparison of the third brake light installation on a car

Image: Visual comparison of the vehicle's rear before and after the LED Third Brake Light installation.

5. Operating Instructions

5.1. Final Inspection

  1. Function Review: Reconnect the battery and thoroughly check all lighting functions (brake, turn signals, reverse, driving lights) once more to ensure they are working correctly.
  2. Sealing Inspection: After washing the car or pouring water over the light area, check for any severe water ingress or fogging inside the lamp. Slight fogging is normal and should clear up and dry naturally.

Video: Product overview and demonstration of the LED Third Brake Light's functionality.

Close-up of the bright red LED lighting effect

Image: Close-up view of the bright red LED lighting effect when illuminated.

6. Maintenance

  • Cleaning: Regularly clean the exterior of the light with a soft cloth and mild automotive cleaner to maintain optimal brightness and visibility. Avoid abrasive cleaners.
  • Periodic Inspection: Periodically check the light for any signs of damage, cracks, or loose connections. Ensure the light is securely mounted.
  • Sealing Check: As part of routine maintenance, perform a sealing inspection (as described in Section 5.1) to ensure no water ingress occurs, especially after car washes or heavy rain.
Image demonstrating the waterproof capabilities of the light in various weather conditions

Image: The light is designed to be waterproof, adapting to various weather conditions like rain, fog, snow, and dust.

7. Troubleshooting

Common Issues and Solutions:

  • Light Not Functioning After Installation:
    • Ensure the electrical connections are secure and properly seated.
    • Verify that the vehicle's battery is properly connected and charged.
    • Check for any blown fuses related to the brake light circuit.
    • Confirm the light is correctly installed and aligned.
  • Water Ingress or Fogging Inside the Lamp:
    • Re-check the sealing around the light and ensure all nuts and covers are tightly secured.
    • Ensure the installation area is clean and free of debris that could compromise the seal.
    • Slight fogging that dissipates naturally is normal; persistent water accumulation indicates a sealing issue.
  • Intermittent Operation:
    • Inspect wiring for any loose connections or damage.
    • Ensure the vehicle's electrical system is stable and providing consistent 12V DC power.

If issues persist after attempting these troubleshooting steps, please contact customer support for further assistance.

8. User Tips

  • Vehicle Compatibility: Always double-check the product's compatibility with your specific vehicle model and year before purchasing and installing.
  • Professional Installation: While designed for plug-and-play, if you are unsure about the installation process, it is recommended to seek professional assistance to avoid potential damage.
  • Regular Cleaning: Keep the light clean from dirt and road grime to ensure maximum visibility and light output.

9. Warranty & Support

For any product-related inquiries, technical support, or warranty claims, please contact the manufacturer or their authorized representative:

  • Manufacturer: Guangzhou Camel Technology Co. Ltd.
  • EU Authorized Representative: MJCM SAR
  • Email: mjcm190928@gmail.com
  • Contact Number: 0033 752907452

An official user manual in PDF format is available for download: View User Manual (PDF)

After-sales Guarantee Guide: Product Damage, Mismatch, Missing Parts

Image: After-sales Guarantee Guide outlining support for product damage, mismatch, or missing parts.

© 2024 MAGIC COLORM. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.