User Manual: VGETTING LED Tail Light Assembly

1. Product Information

Product Name: Tail Light Assembly

Model: FCS-18-26 (Compatible with Toyota Hilux Vigo Pickup 2011-2015)

Brand: VGETTING

This LED Tail Light Assembly is designed as a direct replacement for the original tail lights on Toyota Hilux Vigo Pickup models manufactured between 2011 and 2015. It integrates Brake, Turn Signal, Reverse, and Driving Light functions.

Figure 1: VGETTING LED Tail Light Assembly

2. Important Safety Information & Warnings

Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

• Warning: Keep the device and its cord out of reach of children under 3 years old.
• Keep away from children unless supervised by an adult.
• Do not use this product for purposes other than its intended use.
• Inspect the product before each use; do not use if damaged.
• Follow installation and operation guidelines to avoid injury.
• Do not expose to water or moisture.
• Always disconnect the vehicle's battery before performing any electrical work.

3. Setup (Installation Instructions)

This tail light assembly is designed for direct plug-and-play replacement. Professional installation is recommended.

Step 1: Preparation Work (Safety First)

1. Park the car steadily on a level surface and engage the handbrake.
2. Crucially, disconnect the negative (-) cable from the vehicle's battery to prevent electrical shorts or injury.

Step 2: Remove the Old Tail Light

1. Open the tailgate of your Toyota Hilux Vigo.
2. Locate and remove the tail light repair cover from the inside of the vehicle's body panel.
3. Disconnect the electrical plug connected to the old tail light.
4. Unscrew any visible fixing nuts or bolts holding the tail light in place from the inside.
5. Carefully pull out the old lamp assembly from the outside of the vehicle.

Step 3: Install the New LED Tail Light (Test First, Then Fix)

Pre-testing:

1. Before fully mounting, connect the new LED tail light's plug to the original car harness.
2. Reconnect the negative battery cable.
3. Turn on the vehicle's power (ignition) and test all light functions: brake lights, turn signals (left and right), reverse lights, and driving lights. Ensure they all illuminate normally.

Formal Installation:

1. Once all functions are confirmed to be working correctly, disconnect the negative battery cable again.
2. Align the new LED tail light assembly with its mounting position on the vehicle.
3. Install and tighten all fixing nuts or bolts from the inside of the vehicle.
4. Ensure the electrical plug is securely connected.
5. Replace the maintenance cover inside the tailgate.

Figure 2: Easy Installation - Plug-and-Play Connector

Figure 3: Installation Effect - Before and After

4. Operating Instructions

The VGETTING LED Tail Light Assembly provides enhanced visibility and safety with its multi-functional lighting system.

Light Functions:

• Brake Light: Illuminates brightly when the brake pedal is pressed.
• Turn Signal Light: Flashes amber to indicate turns or lane changes.
• Reverse Light: Illuminates white when the vehicle is in reverse gear.
• Daytime Running Light (DRL) / Driving Light: Provides a constant red illumination for enhanced visibility during normal driving.

Figure 4: Lighting Effects

5. Maintenance

Final Inspection:

1. Reconnect the negative battery cable.
2. Perform a final check of all lighting functions (brake, turn signal, reverse, driving lights) to ensure proper operation.

Sealing Inspection:

After washing the car or after heavy rain, visually inspect the inside of the lamp for any severe water ingress or fogging. Slight fogging is normal and should clear up and dry out with the heat generated by the lights during operation. If severe water ingress persists, check the installation and sealing.

General Care:

• Keep the lens clean using a soft cloth and mild soap solution. Avoid abrasive cleaners.
• Periodically check electrical connections for tightness and corrosion.

6. Troubleshooting

• Lights Not Working:
  • Check if the electrical connector is fully seated and secure.
  • Ensure the vehicle's battery is properly connected and charged.
  • Verify that the vehicle's fuses related to tail lights are intact.
• Partial Lighting or Flickering:
  • Inspect the wiring for any loose connections or damage.
  • Ensure proper grounding.
• Water Inside the Lens:
  • If severe, re-check the installation to ensure the light assembly is properly seated and sealed against the vehicle body.
  • Ensure all mounting points are tightened correctly.

If problems persist after troubleshooting, contact the manufacturer or a qualified automotive technician.

7. Specifications

Figure 5: Product Dimensions

Figure 6: Product Construction Details

Figure 7: Weather Resistance (IP67 Waterproof)

8. User Tips

• Complete Set: Ensure you have both left and right tail light units for a complete and balanced upgrade to your vehicle's rear lighting.
• Pre-Test is Key: Always perform the pre-installation test as described in the setup section to confirm all functions work before fully securing the lights. This saves time and effort.
• Professional Installation: While designed for plug-and-play, if you are unsure about any step, it is always best to consult a professional automotive technician.

9. Warranty & Support

For warranty claims, technical support, or any inquiries regarding your VGETTING LED Tail Light Assembly, please contact the seller or manufacturer directly.

Manufacturer: Guangzhou Camel Technology Co., Ltd.

EU Authorized Representative: MJCM SAR

This product complies with CE standards, as indicated by the Attestation of Compliance (HUT20026631-2ZE, issued Apr. 08, 2021).

A detailed PDF user manual containing additional compliance information may be available for download from the product's original purchase page.