KALADA 050226

Contents

User Manual

KALADA LED Symphony Ambient Lights

Model: 050226 | Brand: KALADA

1. Introduction

This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of your KALADA LED Symphony Ambient Lights. Please read this manual thoroughly before use to ensure proper function and to prevent damage or injury.

LED Symphony Ambient Lights showing colorful light strips and individual lights
The KALADA LED Symphony Ambient Lights system.

2. Safety & Warnings

Important Safety Information:

  • Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
  • Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.

NOTE: This product must comply with all applicable safety and regulatory requirements in the market where it is sold. Sellers must assess which requirements and regulations apply based on the actual product type, function, and destination market.

3. Package Contents

Your package includes the following components. Please verify all items upon receipt.

RGB 6 in 1 kit components including main controller, sub-controllers, and light strips
Example of an RGB 6 in 1 kit's components.

All product types include:

  • 1x Main Controller Module
  • 4x Sub-Controller Modules

Specific configurations vary by item type:

RGB Configurations:

  • 6 in 1: 4pcs 75CM LED strip + 1pcs 110CM double plug LED strip
  • 10 in 1: 4pcs 75CM LED strip + 1pcs 110CM double plug LED strip + 4 *Footlight
  • 14 in 1: 4pcs 75CM LED strip + 1pcs 110CM double plug LED strip + 4 * Footlight + 4 * Door bowl lights
  • 18 in 1: 4pcs 75CM LED strip + 1pcs 110CM double plug LED strip + 4 * Footlight + 4 * Door bowl lights + 4 * Storage lights

Symphony Configurations:

  • 6 in 1 Symphony: 1pcs 110cm + 4pcs 75cm + 1pcs 35cm LED strip
  • 10 in 1 Symphony: 1pcs 110cm + 4pcs 75cm + 1pcs 35cm LED strip + 4 *Footlight
  • 14 in 1 Symphony: 1pcs 110cm + 4pcs 75cm + 1pcs 35cm LED strip + 4 * Footlight + 4 * Door bowl lights
  • 18 in 1 Symphony: 1pcs 110cm + 4pcs 75cm + 1pcs 35cm LED strip + 4 * Footlight + 4 * Door bowl lights + 4 * Storage lights

4. Specifications

Feature Detail
Product Name LED Symphony Ambient Lights
Model 050226
Brand KALADA
Item Type Atmosphere lamp
Voltage 12 V (wide voltage 5V-14V compatible)
Size (Light Strips) 75cm (various lengths included per kit)
Control Method Mobile App (Bluetooth), Double Button Mode
Light Modes Monochrome, Breathe, Gradient, Cycle, Strobe, Music Rhythm, Flow, Running Water
Certification CE, FCC Part 15 Compliant
Origin Mainland China

5. Setup and Installation

Before starting the installation, ensure all components are present and test the complete kit with a 12V power supply (suggested 5A-15A current) to confirm normal operation.

5.1. Preparations

  • Distinguish Modules: The module with a QR Code is the main controller. It controls all sub-modules. The rest are sub-modules.
  • The main module must be powered on for sub-modules to light up.
  • Testing: After receiving the product, connect it to your car's battery (do not use external power supply) to test. If no issues, proceed with installation.

5.2. Download and Install the APP

Search for 'LED LAMP' in your app store or scan the QR code provided on the main control box to download and install the mobile control app. Enable Bluetooth and allow necessary access permissions.

Mobile App Control interface with Bluetooth connectivity
Mobile App Control interface for ambient lights.

5.3. Wiring Instructions

The main module is connected to the fuse box via a plug-in power supply. The door module is powered by the ACC pin type power supply on the door.

Wiring diagram showing main module connected to fuse box and door module to ACC pin
Wiring connections for main and door modules.
  • Main Controller Power:
    1. Connect the Red wire to ACC power or a cigarette lighter fuse (Positive polarity, 5A-15A current).
    2. Connect the Black wire to any ground metal.
  • Sub-Controller Power (Door Modules):
    1. Sub-controllers connect to the Door constant power supply.
    2. Testing Door Panel Power Supply (ACC vs. Constant Power):
      • Constant Power Test 1: If the car flameout, and the door has an automatic window closed function, the door is constant power.
      • Constant Power Test 2: Press the shortcut key to start the car without igniting it. If the window lifter can move up and down, the door is constant power.
      • ACC Power Test: If the door function is not available until the car is ignited, the door is ACC power.

5.4. Light Strip Installation Steps

The LED strips can be cut to length, but avoid cutting into the lamp beads. Cut sections are not reusable.

LED strip showing cutting instructions and wiring details
LED strip cutting and wiring details.
Diagram showing installation locations for ambient lights in a car interior
Recommended installation locations: Footwell, Center Console, Contour, Handle, Saddle, Storage Light.
Central Console:
  1. Remove the trim panel of the center console.
  2. Thread the light strip wires through the holes of the trim panel and connect to the main module.
  3. Secure the light strip to the trim board with 3M tape and cut off excess strip.
  4. Install the trim panel along with the light strip on the center console.
Diagram illustrating light strip installation on the center console
Installation diagram for the center console light strip.
Door Panel:

Four sub-modules are installed in each of the four doors.

  1. Remove the door panel.
  2. Remove the screws of the door trim panel and remove the trim panel.
  3. The acrylic light strip runs from the back of the door panel through the hole in the trim panel to the front of the door panel.
  4. Fasten the light strip to the decorative board with 3M tape.
  5. Install the trim panel along with the light strip to the door panel.
  6. Connect the light strip wires on the back of the door panel to the sub-module.
  7. Install the door panel.
Diagram illustrating light strip installation on a car door panel
Installation diagram for the door panel light strip.

6. Operation

Your ambient lighting system can be controlled via a mobile application (Bluetooth) or through physical buttons.

6.1. Mobile App Control

After downloading the 'LED LAMP' app and connecting via Bluetooth, you can control various aspects of your lights.

Screenshot of the mobile app interface for controlling ambient lights
Mobile App interface for color and mode control.

The app allows you to:

  • Select colors using a color disc or common color presets.
  • Adjust brightness.
  • Choose from various modes: Monochrome, Breathe, Gradient, Cycle, Strobe, Music Rhythm, Flow, Running Water.
  • Customize lighting effects.
  • Control music and audio modes.
  • Turn off the start-up animation (via App settings).
  • Set a favorite color for the welcome light (memory function).
  • Change RGB area or Symphony area modes (e.g., breathe mode, jumping).

Symphony Ambient Light Features:

  • Can display multiple colors simultaneously.
  • Features dual-zone control: light bar and footlight/door light/storage light can have different colors.
  • You can turn off specific areas (e.g., RGB area alone, or Symphony zone alone).
Image highlighting Symphony ambient light's ability to display multiple colors at once
Symphony ambient light displaying multiple colors simultaneously.
Image showing adjustable brightness levels for the ambient lights
Adjustable brightness levels (10%, 30%, 70%, 100%).

6.2. Button Control

The main controller is externally connected with dual control buttons:

  • "M" Button: Controls the illusion light.
  • "S" Button: Controls the RGB light.

Button Functions:

  • Long Press: Turns off the lights.
  • Short Press: Switches modes or turns on the lights.

Other functions like speed and brightness can only be adjusted using the app.

Diagram showing the 'M' and 'S' buttons for light control
Button controls for the ambient lighting system.

Video Demonstration:

Demonstration of the car interior ambient lighting in action, showing color changes and effects.

7. Maintenance

  • After use, turn off the device.
  • Store the device in a dry place.
  • Keep away from children.
  • Regularly check wiring for any signs of wear or damage.
  • Clean the LED strips and controllers with a soft, dry cloth. Do not use harsh chemicals or abrasive cleaners.

8. Troubleshooting

  • If the ambient light does not work after installation:
    1. Remove the kit and connect it directly to the car battery to test again.
    2. If the ambient light works normally, the issue is likely an installation error.
    3. If the ambient light still does not work, it may be a product fault. (One user reported secondary boxes not working despite trying different power sources).
  • If the app cannot be connected or controlled:
    1. Check whether the Bluetooth function of your phone is turned on.
    2. Verify that the device is not connected to another phone.
    3. Restart the app or restart the device.
  • If lights flash or go off when windows are lifted:

    This indicates an unstable power supply. Re-check the positive and negative pole connections and find workable positive wires again.

Troubleshooting guide for app connection issues
Troubleshooting steps for app connectivity.

9. User Tips

  • Installation can be tricky depending on your specific car model; patience and careful routing of wires are key for a clean setup.
  • Always test the complete kit with a 12V power supply before final installation to identify any faulty parts early.
  • Consider your aesthetic preference: some users find that a simpler setup (fewer lights or less intense colors) can be more effective.
  • The 'white' color for the 110cm strip might not be ideal for all users; experiment with other color settings to find your preferred look.

10. Compliance Information

FCC Rules:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.

CE Certification:

The product is CE certified, indicating compliance with European health, safety, and environmental protection standards.

CE and FCC compliance logos
Compliance markings for the product.

Manufacturer & EU Representative:

Manufacturer: Guangzhou Pengzhan Optoelectronics Technology Co., Ltd.
Address: Room 201, 2nd Floor, Huanbao Industrial Park, No. 1-2, Huanbao 2nd Road, Xintang Town, Zengcheng District, Guangzhou, China.

EU Authorized Representative: MJCM SARL
Address: 78 avenue des Champs Elysees Bureau 326, PARIS, FR.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.