superide Superide-26

Contents

SUPERIDE Cycling Helmet User Manual

Model: Superide-26

Introduction

This manual provides essential information for the safe and effective use, maintenance, and care of your SUPERIDE Cycling Helmet. Please read this manual thoroughly before using your helmet and retain it for future reference.

Important Safety Warning:

It is forbidden to disassemble or modify helmet parts without authorization. Do not drill holes or paste heavy objects on the helmet. Do not remove the lining buffer layer. Failure to comply may compromise structural integrity and impact absorption, leading to protection failure.

This helmet is designed for cycling, skateboarding, and roller skating. It is not a bulletproof helmet and should not be used for tactical training or combat against high-speed projectiles. It protects against head impact, sharp object penetration, and debris.

If the helmet has endured a significant impact, even if it appears undamaged, it must be replaced immediately as internal damage may compromise its protective capabilities.

1. Setup and Adjustment

1.1 Preparation for Wearing

  1. Before each use, inspect the helmet shell, lining buffer layer, fixing system, and vent holes for any damage, loosening, or accumulation of stains.
  2. Ensure the lining is firmly installed.
  3. Adjust the head circumference to fit your own size using the internal adjustment system.

1.2 Correct Helmet Fit

  1. Position the helmet on your head to ensure full coverage.
  2. Adjust the lining to fit comfortably.
  3. Fasten the chin strap securely. The buckle should be firm to ensure the helmet is stable and does not shake, and your field of vision is unobstructed.
SUPERIDE Cycling Helmet with Visor and Goggles

Image 1: Helmet with detachable magnetic goggle and removable sun visor. Ensure these are securely attached if used.

Close-up of helmet chin strap buckle

Image 2: Detail of the chin strap buckle. Ensure it is fastened firmly and adjusted for a snug fit.

2. Operating Instructions

2.1 Usage Specifications

  • Use the helmet strictly in applicable scenarios (cycling, skateboarding, roller skating).
  • Avoid hitting hard objects, touching sharp objects, and exposure to chemical corrosives.
  • If matching with other equipment, ensure interfaces are firmly fixed and do not exceed load-bearing limits.
  • Do not place debris on the helmet as it may affect balance.

2.2 Removing the Helmet

  1. Untie the buckle of the chin strap.
  2. Gently remove the helmet upward to avoid pulling the webbing and interfaces.
  3. Store the helmet in a dedicated storage area to prevent scratches and deformation.

2.3 Rearlight Operation

The integrated rearlight enhances visibility. It is powered by a CR2032 button cell battery.

  • To Activate/Deactivate: Press the button on the rearlight unit. Multiple presses may cycle through different light modes (e.g., steady, flashing).
  • Battery Replacement:
    1. Carefully detach the rearlight unit from its housing at the rear of the helmet.
    2. Open the battery compartment (this may require a small screwdriver or prying tool).
    3. Replace the old CR2032 battery with a new one, ensuring correct polarity.
    4. Close the compartment and reattach the rearlight unit securely.
Rearlight circuit board and cover

Image 3: Internal view of the rearlight unit, showing the circuit board and battery housing (battery not shown).

3. Maintenance and Storage

3.1 Cleaning

  1. After use, clean stains, dust, and debris from the helmet surface.
  2. Remove the internal lining and wash with water and a neutral detergent. Reinstall after drying.
  3. Wipe the helmet shell with mild soap and water only.
  4. Avoid contact with hydrocarbons, certain solvents (ammonia), cleaning fluids (bleach), paints, transfers, or other extraneous additions, as these can damage the helmet. Damage may not always be visible.

3.2 Storage

  1. Store the helmet in its own storage bag to prevent squeezing by other hard objects.
  2. Place soft cloth support inside the helmet to prevent lining deformation.
  3. Store tactical accessories separately to avoid wear on the helmet surface.
  4. Store in a cool, dry place away from direct sunlight and extreme temperatures.
Close-up of helmet foam interior

Image 4: Detail of the helmet's EPS foam interior. Inspect regularly for cracks or damage.

4. Troubleshooting

  • Helmet Wobbles/Loose Fit: Ensure the chin strap is securely fastened and adjusted. If the strap buckle does not hold its position, you may need to secure the strap adjustment points (e.g., by stitching) after finding the correct fit.
  • Damage After Impact: If the helmet sustains any significant impact, even if no visible damage is present, it must be replaced immediately. Internal buffer layers can be compromised and may not provide adequate protection in a subsequent impact.
  • Lining Deterioration: Regularly check the inner buffer layer. Replace it if it shows signs of aging, hardening, or cracking.
  • Rearlight Not Working: Check the CR2032 battery and replace it if necessary. Ensure the battery is inserted with correct polarity. Verify the rearlight unit is securely connected.

5. Specifications

FeatureDetail
Model NumberSuperide-26
Weight230g
Size54-61cm
Construction (Outer Shell)In-mold polycarbonate shell
Construction (Inner Shell)EPS liner, Thermoformed reinforcement shock absorbing polystyrene
TypeIntegrally-molded Helmet
Fit SystemLFS - Light Fit System
Air Vents22 Wind Tunnel vents with internal channeling (> 20)
CertificationCE EN 1078, CPSC 1203, AS/NZS 2063
Age Group(Adults) Men, suitable for persons age 5 and older
RearlightIntegrated, powered by CR2032 battery
AccessoriesDetachable Magnetic Goggle, Removable Sun Visor

6. User Tips

  • Chin Strap Security: If the chin strap buckle tends to loosen, consider securing the strap at your preferred adjustment points (e.g., with a few stitches) to maintain a consistent, snug fit.
  • Rearlight Care: The integrated rearlight is not fully waterproof. Protect it from heavy moisture and rain to prevent damage. Regularly check the CR2032 battery for charge and replace it as needed for optimal visibility.
  • Regular Inspection: Periodically check the helmet's foam interior and straps for any signs of wear, cracks, or damage, especially after any impact.

7. Warranty and Support

For specific warranty terms and conditions, please refer to the documentation provided at the time of purchase or contact your retailer. Keep your proof of purchase for any warranty claims.

For further detailed instructions, diagrams, and safety information, please consult the official user manual PDF provided by SUPERIDE.

© 2024 SUPERIDE. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.