1. Introduction and Product Overview
This manual provides essential information for the safe and effective installation and operation of the Vapor Canister Purge Valve Solenoid Valve, model 058133517B. This component is crucial for your vehicle's emission control system, managing fuel vapor flow from the charcoal canister to the engine intake manifold.
For additional documentation, please refer to the User Manual (PDF).
2. Safety and Warnings
Read all instructions before use to ensure safety and prevent damage.
- Warning: This product involves fuel system components. Installation and maintenance must be performed by qualified automotive technicians.
- Warning: Always disconnect the negative battery cable before operation to prevent fire caused by electrical short circuits.
- Warning: The use of fuel that does not meet EU environmental standards is prohibited, as it will shorten the service life of the canister and solenoid valve.
- Warning: Product failure may result in fuel vapor leakage, posing risks of fire or environmental pollution. If a malfunction is detected, stop using the product immediately and arrange for repair.
3. Specifications
| Attribute | Detail |
|---|---|
| Product Name | Vapor Canister Purge Valve / Solenoid Valve / Breather Valve |
| Model | 058133517B |
| OEM NO. | 058133517B, 6QE906517A |
| Part Number (VW Audi) | 058133517B, 6QE906517A, 6Q0906517A |
| Part Number (Bosch) | 0280142347 |
| Material | Plastic And Metal |
| Origin | Mainland China |
Compatible Vehicles:
- Compatible with VW: 2006-2015 EOS, 2003-2009 GOLF V, 2009- POLO, 2007- TIGUAN
- Compatible with Audi: 1994-2001 A4, A4 Avant
- Compatible with Seat: 2005-2012 LEON
4. Installation Guide
4.1. Pre-Installation Preparation
- Ensure the vehicle is turned off.
- Disconnect the negative battery cable to prevent electrical hazards.
- Prepare special tools: a torque wrench, a clip remover, and sealing grease.
4.2. Installation Steps
-
Remove the Old Solenoid Valve:
- Mark the positions of all connecting hoses for correct re-installation.
- Use the clip remover to release hose clips.
- Disconnect the electrical connector of the old solenoid valve.
- Remove the mounting bolts.
- Carefully take out the old solenoid valve.
-
Clean the Installation Area:
- Clean any oil stains and impurities from the mounting base and hose connectors to ensure a proper seal.
-
Install the New Solenoid Valve:
- Align the new solenoid valve with the mounting base.
- Tighten the mounting bolts. Note: Consult your vehicle's service manual for the specific torque value in N·m.
- Connect all hoses and secure the clips, ensuring no twisting of hoses.
- Fully insert the electrical connector and confirm it is locked in place.
Figure 3: Detailed view of the valve, showing electrical connector and hose ports. -
Post-Installation Inspection:
- Reconnect the negative battery cable.
- Start the vehicle and check for any fuel leaks.
- Read vehicle fault codes using a diagnostic tool to confirm no system abnormalities.
4.3. Installation Precautions
- Do not pull or bend the electrical wiring harness during installation to avoid damaging internal wires.
- Hose connections must be secure to prevent fuel vapor leakage and safety hazards.
5. Operating Instructions
The Vapor Canister Purge Valve operates automatically as part of your vehicle's engine management system. Once correctly installed, it requires no manual intervention. Its function is to regulate the flow of fuel vapors from the charcoal canister to the engine, ensuring proper emission control and fuel efficiency.
Ensure all connections are secure and free from leaks for optimal performance.
6. Maintenance
The Vapor Canister Purge Valve is generally a maintenance-free component. Regular vehicle maintenance, including checking the emission system for fault codes, can help identify potential issues early. If a malfunction is detected, it is recommended to replace the valve rather than attempt repairs.
Ensure that the fuel used meets the manufacturer's specifications to prolong the life of emission system components, including this valve.
7. Troubleshooting
Common symptoms of a faulty purge valve may include:
- Check Engine Light (CEL) illuminated, often with EVAP system related codes (e.g., P0441, P0442, P0446).
- Rough idle or stalling.
- Difficulty starting the engine, especially after refueling.
- Reduced fuel economy.
- Strong fuel odor.
If you experience any of these symptoms, it is recommended to have the vehicle diagnosed by a qualified technician. A diagnostic scan tool can confirm if the purge valve is the cause of the issue.
If fuel vapor leakage is detected, stop using the product immediately and arrange for repair to prevent fire or environmental pollution.
8. User Tips
No specific user tips were available from provided reviews or Q&A content. Always ensure proper vehicle diagnosis before replacing parts to avoid unnecessary repairs.
9. Frequently Asked Questions (FAQ)
No specific FAQ content was available from provided Q&A data.
10. Warranty and Support
For warranty information and technical support, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.
Manufacturer: Ruian Lizeng Auto Parts Factory, CN
EU Authorized Representative: SUCCESS COURIER SL, CALLE RIO TORMES NUM. 1, PLANTA 1, DERECHA, OFICINA 3, Fuenlabrada, Madrid, 2847 Spain