1. Security Summary
Welcome to our DC regulated power supply (referred to as the power supply). This manual contains essential safety instructions that must be followed for the operation, use, and storage environment of this product series. To ensure your personal safety, please thoroughly read this manual before operation to avoid personal injury due to improper handling or damage to the power supply and other connected load equipment.
Safety Symbols
The following safety symbols may appear in the manual or on the machine:
-
Warning Label
-
High Volt Danger
-
Grounding
-
Certification Mark (CE)
-
Do Not Litter
-
Indoor Use
2. Product Overview
The TPA series is a digital display programmable switching DC regulated power supply that can simultaneously display voltage, current, and power. This power supply is widely used in product aging, battery charging, R&D testing, schools, and production lines. Its output voltage and current are both adjustable via an encode knob, continuously adjustable between 0 and the nominal value.
The power supply has excellent stability and ripple coefficient, and features multiple protection circuits including short-circuit protection, overvoltage protection, overcurrent protection, and overtemperature protection.
The product boasts an attractive design, user-friendly operation, and the ability to work at full capacity for extended periods. It is equipped with a USB fast charging interface and offers optional PC software control functionality, making it a popular choice among users.
3. Specifications (Machine Parameter Table)
The above parameters were measured at an ambient temperature of 25±5°C, relative humidity <80%RH, and after preheating for 30 minutes. Actual parameters may vary slightly.
| Attribute | Value |
|---|---|
| Model | TPA3010 |
| Output Volt | 0-30V |
| Output Current | 0-10A |
| Output Power | 0-300W |
| Fuse | 3.15A |
| Accessibility | Dual fast charging ports, short circuit protection, four storage groups, lock function, buzzer, one-button output. |
| C.V (Constant voltage state) - Voltage Stability | ≤0.5% +3mV |
| C.V (Constant voltage state) - Load Stability | ≤0.5% +3mV |
| C.V (Constant voltage state) - Ripple | ≤0.5% Vp-p |
| C.C (Constant current state) - Current Stability | ≤0.5% +3mA |
| C.C (Constant current state) - Load Stability | ≤0.5% +3mA |
| C.C (Constant current state) - Ripple | ≤0.5% Ap-p |
| Product Dimensions | Length 214mm, Width 90mm, Height 156mm |
| Net Weight | 1.17 kg |
| Gross Weight | 1.55 kg |
| Operating Temperature | 0°C - 40°C, Relative humidity: <80%RH |
| Storage Temperature | -10°C - 50°C, Relative humidity: <70%RH |
| Protection Method | Overvoltage Protection, Overcurrent Protection, Overtemperature Protection, Short Circuit Protection |
| Display Accuracy | 0.5% + 3 words |
| Maximum Resolution | Volt: 0.001V; Current: 0.001A |
4. Front Panel Introduction
The front panel provides all necessary controls and displays for operating the DC power supply.
| No. | Component | No. | Component |
|---|---|---|---|
| 1 | Voltage Display | 12 | Short-Circuit/Overcurrent Protection Switch (OCP) |
| 2 | Current Display | 13 | Over Voltage Protection Switch (OVP) |
| 3 | Power Display | 14 | Buzzer Switch |
| 4 | C.V (Constant Voltage Indicator Light) | 15 | Output Switch |
| 5 | M1-M4 Storage Indicator Light | 16 | USB-A Fast Charging Port |
| 6 | C.C (Constant Current Indicator Light) | 17 | USB-C Fast Charging Port |
| 7 | OPN Indicator Light | 18 | Power Switch |
| 8 | Current adjustment knob | 19 | Negative Output Port (Black) |
| 9 | Voltage Adjustment Knob | 20 | Ground Terminal (Green) |
| 10 | Button Lock Switch | 21 | Positive Output Port (Red) |
| 11 | Storage Selection/Storage Value Setting Switch |
5. Back Side Description
The back panel includes essential connections and features for power input and cooling.
| No. | Component |
|---|---|
| 22 | Temp-Controlled Cooling Fan |
| 23 | Power Outlet |
| 24 | Fuse Box |
| 25 | USB/RS-232/RS-485 Communication Port (Optional) |
6. Setup and Initial Connection
6.1 AC Input
Please verify the AC voltage input permitted for this machine. Refer to the label information located near the power outlet on the back of the machine. The supported inputs are:
- 230V ±10% 50Hz
- 115V +10% 60Hz
Warning:
Incorrect AC voltage input will cause serious damage to the machine. Please ensure that the machine requires the correct input voltage.
6.2 Connect the Ground Wire
When using this product, please ensure the power cord is properly grounded. If the power outlet does not have a ground wire, you can use a wire to connect the machine's grounding terminal to the earth. Proper grounding can effectively prevent machine leakage and reduce output ripple interference.
Important:
Proper grounding effectively prevents machine leakage and can also reduce output ripple interference.
6.3 Connect the Load Device
- Securely connect the output wires to the power supply terminals according to the positive (+) and negative (-) markings.
- Securely connect the other end of the output lead to the positive terminal of your load device.
Notice:
Incorrect connections may damage the power supply and the load connected to it. When connecting loads such as batteries, do not reverse the "+" and "-" terminals, as this may damage the power supply.
7. Operating Instructions
7.1 Constant Voltage Constant Current Mode
The power supply output modes are divided into two types: constant voltage output (C.V) and constant current output (C.C). The output mode is determined by the voltage and current values set by the user and the load connected to the power supply. The voltage or current value output by the power supply will not exceed the voltage and current values set by the user. In constant voltage mode, the output voltage is equal to the user-set voltage value. In constant current mode, the output current is equal to the user-set current value.
Note:
During actual CV operation, if the load resistance decreases and causes the output current to increase to the set current value, the power supply will automatically switch to CC mode. When the load resistance continues to decrease, the current will remain at the set current value while the voltage proportionally decreases (I=V/R). At this point, increasing the load resistance or raising the current set value will restore the CV output mode.
7.2 VOLTAGE Adjustment Knob
Used to adjust the voltage setting. Rotate clockwise to increase the value; rotate counterclockwise to decrease the value. Pressing the voltage knob will jump to the left, skipping a character position. After 3 seconds, the flashing will stop and the current setting value will be saved.
7.3 CURRENT Adjustment Knob
Used to adjust the current setting. Rotate clockwise to increase the value; rotate counterclockwise to decrease the value. Pressing the current knob will jump to the left. The flashing will stop 3 seconds after the current setting is complete, and the current setting will be saved.
7.4 LOCK Button Lock Switch
Used to lock the state of the push-button switches (excluding the power switch and LOCK button lock switch) and adjustment knobs on the front panel to prevent accidental operation.
7.5 Memory Storage Group Selection/Storage Value Setting
This machine has four sets of memory functions, which makes it easy to store and recall frequently used parameters.
- Storage Group Selection: Press the MEMORY button to select any one of the four preset voltage/current storage values. The selection result can be confirmed through the display screen and the M1~M4 storage indicator lights on the display screen.
- Stored Value Settings: For example, to change the value stored in M2, press the MEMORY button to select M2 for storage, press and hold the MEMORY button for 3 seconds to enter the parameter setting interface (you will hear two "beep" sounds), then use the VOLTAGE/CURRENT knob to adjust to the desired voltage/current value. After modification, press and hold the MEMORY button for 3 seconds within 8 seconds to save, and the setting will be completed (you will hear two "beep" sounds); if you do not save within 8 seconds, the parameter setting interface will be automatically exited without saving.
7.6 OCP Short-Circuit Protection/Overcurrent Protection Switch
Press the OCP button to enable / disable the OCP short-circuit protection / overcurrent protection function. When this function is enabled, the button indicator light will illuminate. If a short circuit or overcurrent occurs in the load, the machine will stop output and issue an alarm. Pressing the OUTPUT button or the OCP button will deactivate the alarm and shut off the power output. (The machine determines whether a short circuit exists by checking if the output current exceeds the user-set current. Therefore, the machine cannot be used in constant current CC mode when the OCP short-circuit protection function is enabled.)
7.7 OVP Over Voltage Protection Switch
Press the OVP button to enable/disable the OVP overvoltage protection function. When this function is enabled, the button light will illuminate. When an overvoltage occurs, the machine will stop outputting and issue an alarm. Pressing the OUTPUT button or the OVP button will deactivate the alarm and turn off the power output.
- OVP Parameter Setting Method: Press and hold the OVP button for 3 seconds to enter the OVP parameter setting interface (you will hear two "beep" sounds). Use the VOLTAGE knob to adjust to the desired voltage protection value. After modification, press and hold the OVP button for 3 seconds within 8 seconds to save the settings (you will hear two "beep" sounds). If you do not save within 8 seconds, the settings will be automatically exited without saving.
7.8 Buzzer Switch
Press the Buzzer button to turn the buzzer on or off.
7.9 OUTPUT Output Switch
Press the OUTPUT button to turn the power output on or off.
7.10 OPN Function (Power-on output status: on or off)
The OPN function controls whether the OUTPUT button is ON or OFF each time the device is powered on.
- How to enable/disable the OPN function: With the OUTPUT button OFF, press and hold the OUTPUT output button for 3 seconds to enter the settings interface (you will hear two "beep" sounds). Press the OUTPUT button or rotate the VOLTAGE/CURRENT knob to select whether the OPN function is on or off. After making your selection, press and hold the OUTPUT button for 3 seconds to save and exit (you will hear two "beep" sounds).
7.11 USB Fast Charging Function
This device features USB fast charging and has a built-in multi-protocol fast charging identification chip, with a maximum output power of 18W.
7.12 Host Computer Communication (Optional)
Users can choose models equipped with USB / RS-232 / RS485 communication modules to communicate with a host computer via the MODBUS protocol, enabling remote control.
- RS-485 Address Setting Method: Press and hold the VOLTAGE knob for 3 seconds to enter the address setting interface. Adjust the VOLTAGE knob to set the RS-485 address. After setting, press and hold the VOLTAGE knob to save and exit.
8. Product Maintenance
8.1 Regular Inspection, Cleaning, and Maintenance
Regular inspection, cleaning, and maintenance of the machine can help extend its lifespan. Please follow the steps below to maintain your machine:
- Turn off the power switch and unplug the power cord from the socket.
- Gently wipe the casing, top cover, and vents with a soft cloth and mild detergent.
- Visually inspect all power cords and terminals for damage such as impact, loosening, heat corrosion, moisture, or insect bites.
Replace any damaged power cords or terminals with those of the same specifications and dimensions.
8.2 Replace Fuse
If the fuse blows, the machine will stop working. Find and correct the cause of the blown fuse before replacing it with a fuse of the same specifications.
Warning:
For effective safety protection, only fuses of specific specifications should be replaced. Do not unplug the power cord before replacing the fuse.
9. Troubleshooting
- No Output / Alarm Sounding: If the device stops outputting and an alarm sounds, check the display for OCP (Overcurrent Protection) or OVP (Overvoltage Protection) indicators.
- OCP Triggered: This indicates a short circuit or the load current exceeding the set output current. Disconnect the load, identify and resolve the short circuit or reduce the load, then press the OUTPUT or OCP button to deactivate the alarm and reset.
- OVP Triggered: This indicates the actual output voltage is higher than the set OVP limit. Disconnect the load, check for any issues causing overvoltage, then press the OUTPUT or OVP button to deactivate the alarm and reset.
- No Power: If the unit does not power on, check the power cord connection and ensure the AC input voltage matches the device's requirements. Verify the fuse is not blown (refer to section 8.2 for fuse replacement).
- Inaccurate Output: If the output voltage or current appears inaccurate, ensure proper load connection and check for any loose terminals. Allow the unit to preheat for 30 minutes for optimal accuracy.
- Buttons/Knobs Unresponsive: Check if the LOCK function is enabled. If the LOCK indicator is lit, press the LOCK button to unlock the controls.
10. User Tips
- Pre-set Values for Efficiency: Utilize the 4 memory storage groups (M1-M4) to save frequently used voltage and current settings. This can significantly speed up your workflow for repetitive tasks.
- Safety First: Always double-check your connections, especially polarity, before enabling output, particularly when working with sensitive components or batteries.
- Monitor Display: Pay attention to the C.V (Constant Voltage) and C.C (Constant Current) indicator lights to understand the current operating mode of the power supply.
- Use OCP/OVP: Always set appropriate OCP and OVP limits to protect your circuits and the power supply from accidental damage.
- Keep it Clean: Regularly clean the unit, especially the cooling fan vents, to ensure optimal performance and longevity.
11. Warranty and Repair
11.1 Product Inspection
Each product comes with an instruction manual and a certificate of conformity to ensure that users can use our products correctly. All products manufactured and inspected by our company are produced and inspected according to the manufacturer's standards; any unqualified products will never leave the factory.
11.2 Product Warranty
One-year warranty (excluding damage caused by human error).
11.3 Product Repair
- Free repair or replacement of parts is provided during the warranty period. After the warranty period, paid repair services are available.
- During the product's service life, if the product malfunctions, the company is only responsible for the malfunction and loss of the product itself; the company does not bear any load or other related losses.
Guarantee Limitations:
The following warranties do not apply to losses caused by the following circumstances:
- Customer violation of the usage instructions in this manual
- Customer disassembly or repair of the product
- Unauthorized modifications or misuse
- Operation of the product outside the specified environment
- Force majeure factors under relevant laws
12. Packing List
- Main unit x1
- Power cord x1
- Output load cable x1
- User manual x1
- Warranty card and certificate of conformity x1
13. Contact Information
Shenzhen Toviyon Electronic Technology Co., Ltd.
Address: Room 203, 2nd Floor, No. 69, Langkou Industrial Park, Langkou Community, Dalang Subdistrict, Longhua District, Shenzhen
Web: www.toviyon.com
Tel: (+86)18588483965
WhatsApp: +1(424)413-3536
WeChat: 18588483965