AULA MINI 60HE Magnetic Keyboard User Manual

1. Introduction

The AULA MINI 60HE is a high-performance, tri-mode magnetic axis keyboard designed for gaming and general use. It features a stylish 61-key layout, hot-swappable keycaps and switches, and advanced magnetic switch technology for precise and rapid response. This manual provides detailed instructions for setup, operation, maintenance, and troubleshooting to ensure optimal performance and user experience.

2. Setup

2.1 Connection Methods

The AULA MINI 60HE supports three connection modes: Wired, 2.4G Wireless, and Bluetooth. Ensure the keyboard is charged before initial use.

Wired Mode

1. Slide the switch on the keyboard to the middle position for wired mode.
2. Insert the USB cable into the Type-C interface of the keyboard and connect the other end to your computer's USB port.

2.4G Wireless Mode

1. Slide the switch on the keyboard to the left position for 2.4G mode.
2. Press and hold the FN + R keys for 3 seconds. The cyan light on the R key will flash rapidly to indicate pairing mode.
3. Insert the 2.4G receiver into a USB port on your computer. The R key's cyan light will stay on for 2 seconds, indicating a successful 2.4G connection.
4. Note: It is recommended to search for the device before inserting the receiver. The device comes pre-paired from the factory.

Bluetooth Mode

The keyboard can connect to up to three Bluetooth devices. The device name for Pro/MAX versions is 'MINI 60 HE Pro-X' (where X is 1, 2, or 3) and for Standard version is 'MINI 60 HE'.

1. Slide the switch on the keyboard to the right position for Bluetooth mode.
2. To pair with a new device:
• Press FN + Q (for device 1), FN + W (for device 2), or FN + E (for device 3) and hold for a long press to enter pairing mode. The blue indicator light for the selected channel will flash rapidly.
• On your device (computer, smartphone, tablet), search for 'MINI 60 HE' (or 'MINI 60 HE Pro-X') in Bluetooth settings and connect.
• Once connected, the blue light will stay on for 2 seconds.
3. To reconnect to a previously paired device:
• Short press FN + Q, FN + W, or FN + E. The blue light will flash slowly and then stay on for 2 seconds upon successful reconnection.
4. To view the current connection mode, BT channel, and system mode, press and hold the FN key. The corresponding buttons will light up in white. Release FN to restore the light effect.

2.2 Driver Installation

For full customization of magnetic switch functions, macro definitions, and lighting effects, it is recommended to install the keyboard's driver software. Consult customer service for the driver link if not provided with the product.

3. Operating Instructions

3.1 Keyboard Layout and Features

The MINI 60HE features a 61-key layout, offering a compact design for more mouse operation space. It is built with high-quality materials for a solid feel and responsive keys.

Key features include:

• Hot-swappable: Keycaps and mechanical switches can be easily replaced for customization.
• Magnetic Switches: Customizable magnetic switch travel range from 0.1 to 3.3/3.4mm with 0.01mm RT adjustment precision.
• High Performance: 8000Hz polling rate (wired), 1000Hz (2.4G), 125Hz (BT), and 128KHz scan rate for ultra-responsive gaming.
• Anti-Ghosting: Full-key anti-ghosting supported across all connection modes.
• Independent Receiver Storage: A dedicated compartment for the 2.4G wireless receiver.

3.2 Backlight Effect Adjustment

The keyboard features approximately 16 million colors RGB backlight with 20+ preset lighting effects. Single-key customization is supported via the driver software.

Use the following key combinations to adjust backlight effects:

• Press FN + \| to cycle through 19 RGB lighting effects.
• Press FN + Enter to switch backlight colors.
• Press FN + F5 to decrease backlight brightness.
• Press FN + F6 to increase backlight brightness.

3.3 Operating System Mode Switching

Switch the keyboard's operating mode to match your connected device:

• Press FN + A to switch to Android mode. The A key's red light will flash for 3 seconds.
• Press FN + S to switch to Windows mode. The S key's red light will blink for 3 seconds.
• Press FN + D to switch to Mac mode. The D key's red light will flash for 3 seconds.

3.4 Shortcut Key Description

The keyboard utilizes the FN key in combination with other keys to access various functions:

Android System (A key flashes red for 3s) F-Zone Functions:

When in Android mode, the F-keys (F1-F12) have dedicated functions. Pressing the F keys alone activates these functions. For multimedia functions, use FN + F-key.

Windows System (S key blinks red for 3s) F-Zone Functions:

3.5 Magnetic Axis Adjustment Method

The keyboard's magnetic switches offer advanced customization through the driver software. These functions allow for fine-tuning of key behavior:

• Dynamic Key Stroke (DKS): Modify key functions based on different levels of press and release, binding 1 to 4 functions per key.
• Dual-Effect Click (MT): Assign two functions to a single key; one for holding the key down, and another for clicking it.
• Toggle Switch (TGL): A single click can toggle continuous trigger on/off, while holding the key performs normal trigger behavior.
• Simultaneous Opposing Cardinal Directions (SOCD): Monitors two selected keys and activates them based on your chosen settings.
• Rappy Snappy: Monitors at least two selected keys and activates the key that is pressed deeper.
• Rapid Trigger (RT): Dynamically adjusts actuation and reset distances based on your intent to press or release the key.
• Visualized Rapid Magnetic Axis Travel Calibration: Allows independent adjustment of the travel distance for each key.

4. Maintenance

4.1 Charging Instructions

The keyboard is equipped with a rechargeable lithium battery (4000mAh for Pro/MAX, 3000mAh for Standard). It supports USB-C connectivity for reliable, stable, and faster charging.

To check battery level: Press FN + B (the 1-0 keys will show green backlight indicating charge level), or connect via Bluetooth to check on a computer.

Charging Indicators:

• Pro/MAX Version: When charging, the ESC red light stays on for 10 seconds before turning off. When fully charged, the ESC blue light stays on for 10 seconds before turning off. When the battery is low, the ESC flashes a red light.
• Standard Version: When charging, the ESC red light stays on for 10 seconds before turning off. When fully charged, the ESC blue light stays on for 10 seconds before turning off. When the battery is low, the ESC flashes a red light.

Important Charging Recommendations:

1. It is recommended to use only the computer's USB port to charge the keyboard.
2. Do not use fast-charging cell phone chargers to charge the keyboard.
3. Do not use inferior non-standard power adapters to charge the keyboard.
4. Do not use over-voltage and over-current power adapters to charge the keyboard.
5. Please keep away from high-temperature equipment when charging.
6. Please turn off the power switch if the keyboard is not used for a long time.

5. Troubleshooting

5.1 General Notes and Warnings

• Due to the special triggering principle of magnetic axis keyboards, bumpy movement during transportation may affect triggering accuracy. Please open the driver after receiving the keyboard and calibrate all keys.
• For a more stable 8000Hz refresh rate, it is recommended to connect to a USB 2.0 high-speed interface or a USB 3.0 and above port using the original keyboard cable.
• Keycap characters may differ due to different production batches. The hot sublimation process keycaps are manually made, and the pattern position and color may vary from pictures. The actual product shall prevail.
• Keyboard streamers (if included) need to be manually installed.

5.2 Common Issues and Solutions

• Keys not responding or behaving unexpectedly: Ensure the keyboard drivers are installed and updated to the latest version. Calibrate the magnetic switches using the driver software.
• Connectivity issues: Verify the correct connection mode (Wired, 2.4G, or Bluetooth) is selected. For 2.4G, ensure the receiver is properly inserted. For Bluetooth, re-pair the device if necessary.
• Backlight not working: Check if the backlight is turned off (FN + BackSpace). Adjust brightness using FN + F5/F6.

6. Specifications

6.1 General Product Parameters

6.2 Magnetic Switch Specifications

The keyboard is available with different magnetic axis types, each with specific characteristics:

7. User Tips

• Driver Installation is Key: For optimal performance and to unlock all customization features, ensure you install the official driver software. Some users have reported resolving key issues after installing and updating drivers.
• Calibration after Transport: If you notice any inconsistencies in key triggering, especially after the keyboard has been transported, use the driver software to calibrate the magnetic switches.
• Use Original Cable for Best Performance: For the most stable 8000Hz refresh rate in wired mode, always use the original keyboard cable and connect to a USB 2.0 high-speed or USB 3.0 (or higher) port.

8. Warranty & Support

For detailed item guides and documents, please refer to the official PDF manual: User Manual (PDF).

This product is manufactured by Dongguan Suoai Electronics Co.,Ltd and commissioned by Shenzhen Suoai Electronics Co.,Ltd.

For further support, please visit the official website: www.aulacn.com.