Introduction
Thank you for purchasing the BRS-H22 Double Head Outdoor Heater. This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your new heater. Please read this manual thoroughly before using the product and keep it for future reference.

Figure 1: BRS-H22 Double Head Outdoor Heater
Important Safety Warnings
Failure to follow these instructions may result in fire, explosion, injury, or death.
- This product can only be used outdoors or in a well-ventilated environment. It is strictly prohibited for use in tents, cars, indoors, or other closed environments.
- Avoid using in hot sun or other high-temperature environments.
- Before use, carefully check for gas leakage. If gas leakage is detected, stop using immediately.
- Do not attempt to disassemble or modify the product structure yourself to avoid danger.
- It is strictly forbidden to disassemble and install the gas tank when the fire is not out, and it is strictly forbidden to disassemble and install the gas tank near an open flame.
- Keep away from flammable and explosive objects when using.
- Do not place your body parts (pay attention to your head and hands) above the stove to avoid burns.
- Children under 12 years old should not use this product alone.
- It is strictly prohibited to fall down or tilt when using the product, otherwise, an open flame may appear and cause fire danger.

Figure 2: Safety Warnings and Attention Notes
Setup Instructions
1. Prepare the Gas Tank
The BRS-H22 heater is compatible with multiple gas sources. Ensure your gas tank is suitable and in good condition.
- 450g Tank: Can be used continuously for approximately 6-7 hours.
- 230g Tank: Can be used continuously for approximately 3.5 hours.
- With BRS-113 Tank Holder: Use with a tank holder for increased stability.
- With BRS-17 Converter: A 220g tank can be used continuously for approximately 3.5 hours.

Figure 3: Compatible Gas Tank Types and Usage Durations
2. Connect a Tank
- Make sure the valve switch on the heater is closed (turn clockwise).
- Connect and tighten the gas tank to the stove's connecting head.
Note: Check whether there are air leaks before ignition. If you smell an odor (like onions), immediately stop the ignition process and check connections or replace the tank.

Figure 4: Tank Connection and Ignition Steps
Pre-Use Check
- Please check whether the O-type sealing rubber ring exists and is in good condition in the connection between the valve body and the tank before use.
Operating Instructions
1. Ignite the Burner
- Slowly open the valve switch counter-clockwise. Do not open it too wide initially.
- Use an external ignition source (e.g., a lighter or match) to ignite the burner at the lighting-up tuyere.
Warning: Do not place your head or other parts of your body above the stove when lighting the fire.
2. Adjust Heat
Adjust the valve switch to control the flame size and heat output as needed. The heater features a dual high-efficiency heating head for instant, rapid heating.

Figure 5: Heater Components (Dual Heating Head, Reflector, Ignition Port, Air Intake Hood)
3. Close the Stoves
- Close the valve switch (turn clockwise) to extinguish the flame.
- Allow the stove to cool completely for at least 5 minutes before handling.
Maintenance
- Keep the stove dry and clean to avoid corrosion.
- Discoloration of the support and furnace head is a normal phenomenon during use.
- After use, please keep the dustproof cover to avoid impurities entering the airway and causing blockage.
- For storage, be sure to separate the stove and gas tank.
- Store the gas tank in a well-ventilated area.
- Do not install or disassemble in places with open flame or poor ventilation.
Troubleshooting
- Gas Leakage: If you detect a gas smell (like onions) or hear a hissing sound, immediately turn off the gas supply, disconnect the tank in a well-ventilated area, and do not attempt to ignite. Check all connections, the O-ring, and the tank for damage. If the issue persists, do not use the heater and seek professional assistance.
- No Ignition: Ensure the gas tank is properly connected and has fuel. Check that the valve is open sufficiently. Use a reliable external ignition source.
- Unstable Flame: Ensure the heater is placed on a smooth, stable surface. If using a smaller tank, consider using a tank bracket (like BRS-113) for more stability.
Specifications
| Feature | Detail |
|---|---|
| Model Name | BRS-H22 Owl Double Heating Furnace |
| Type | Gas Stove / Outdoor Heater |
| Dimensions | 215 x 200 x 125 mm |
| Power | 1050W |
| Gas Consumption | 63g/h |
| Weight | 480g |
| Material | High temperature resistant stainless steel, aluminum alloy, copper alloy |
| Fuel Type | Butane gas, Propane gas |
| Ignition Device | Included (External ignition source required) |
| Disposable | No |
| Origin | Mainland China |

Figure 6: Detailed Product Specifications
User Tips
No specific user tips from reviews or Q&A were available for this product. However, general tips for outdoor heaters include:
- Always ensure adequate ventilation, even in outdoor settings, to prevent carbon monoxide buildup.
- Keep a safe distance from tents, sleeping bags, and other flammable materials.
- Consider carrying a spare gas tank for extended trips.
- Always pack the heater and gas tanks separately and securely to prevent damage during transport.
Warranty and Support
For warranty registration, troubleshooting, and service inquiries:
- If you have registered your product for warranty, please log in to the JHEDENG OUTDOOR PRODUCTS WeChat official account for troubleshooting and warranty services.
- If your product has not been registered for warranty, please contact the dealer from whom you purchased the product.
- Hotline: +86-579-87111023
- Company Website: www.brs.net.cn
- Manufacturer: JHEDENG OUTDOOR PRODUCTS CO LTD, No 6-1, Fengshanzui, Longshan Town, Yongkang City, Zhejiang Province, China.

Figure 7: Product Manual Cover with Manufacturer Details