M328 M328

Contents

M328 Transistor Tester Instruction Manual

Model: A25F-M328

1. Product Overview

The A25F-M328 Transistor Tester is a versatile instrument designed for automatic detection and measurement of various electronic components. It features a TFT color display for clear reading of measurement data and graphs.

M328 Transistor Tester displaying capacitance, ESR, and Vloss values.

Figure 1: M328 Transistor Tester displaying a capacitance measurement (91.08µF, ESR=.24Ω, Vloss=1.5%).

2. Safety & Warnings

  • This product is intended for adult use only.
  • Keep out of reach of children and pets to prevent accidental injury or ingestion.
  • Always ensure the device is correctly set up before use.
  • If you observe abnormal noise or equipment errors during operation, immediately stop using the device.
  • Follow all instructions for proper use. Misuse may lead to harm or damage to the device.
  • Store the device in a dry and shady place, away from high temperatures, humidity, and direct sunlight.

3. Setup

  1. Power Supply: The M328 Transistor Tester is powered by a 9V battery (not included). Open the battery compartment, insert a fresh 9V battery, and close the compartment securely.
  2. Initial Inspection: Before first use, inspect the product for any signs of damage. Do not use if damaged.
  3. Familiarize with Controls: Identify the 'OFF' button to quickly close the device and the 'TEST' button to open and initiate measurements.
  4. Test Interface: The device features a test interface with pins labeled 1, 2, 3 for connecting components.
Diagram of M328 Transistor Tester showing working indicator light, display screen, quick close button, open/test button, and test interface.

Figure 2: Key functional areas of the M328 Transistor Tester.

4. Operating Instructions

The M328 Transistor Tester offers one-click measurement and automatic recognition of components.

  1. Connecting a Component: Carefully insert the leads of the component you wish to test into the designated test interface pins (1, 2, or 3). Ensure a secure connection.
  2. Initiating Measurement: Press the 'TEST' button to power on the device and begin the measurement process. The device will automatically identify the component type and measure its parameters.
  3. Reading Results: Measurement data and graphs will be displayed on the TFT color screen. The detection time is typically 2 seconds, though it may take up to 1 minute for capacitors.
  4. Power Off: The device features an auto power-off function to save battery. You can also press the 'OFF' button to manually turn off the device.
Hand holding M328 Transistor Tester with text 'One-click measurement and automatic recognition'.

Figure 3: One-click measurement and automatic recognition feature.

5. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the device. Do not use abrasive cleaners or solvents.
  • Storage: When not in use, store the transistor tester in a dry, cool, and shady environment. Avoid exposure to extreme temperatures, high humidity, and direct sunlight.
  • Battery: If the device will not be used for an extended period, remove the 9V battery to prevent leakage and potential damage.

6. Troubleshooting

  • "No, unknown, or damaged part" message: If the display shows this message (see Figure 4), it indicates that the connected component is either not recognized, damaged, or incorrectly connected. Ensure the component is functional and properly inserted into the test interface.
  • Device not powering on: Check if the 9V battery is correctly installed and has sufficient charge. Replace the battery if necessary.
  • Inaccurate readings: Ensure the component leads are clean and make good contact with the test interface. For capacitors, allow sufficient time for measurement (up to 1 minute).
  • Abnormal noise or equipment error: Immediately cease operation and consult the manufacturer or authorized representative if you experience any unusual behavior from the device.
M328 Transistor Tester displaying 'No, unknown, or damaged part'.

Figure 4: Error message indicating an unrecognized or damaged component.

7. Specifications

Feature Description
Product Name M328 Transistor Tester
Display TFT Color Display
Power Supply DC9V (9V battery, not included)
Dimensions 69mm x 133mm x 24mm
Supported Language English
Transistor Range Transistors with 2 or fewer PN junctions (including 2), without other resistors or capacitors inside.
Resistance Measurement 0.5Ω - 50MΩ
Inductance Measurement 0.01mH - 20H
Capacitance Measurement 25pF - 100000uF
Detection Time 2 seconds (1 minute for capacitors)
Material Plastic
Color White

8. User Tips

  • For optimal performance and accurate readings, always use a fresh 9V battery.
  • When testing components, ensure the leads are clean and make firm contact with the test sockets to avoid false readings.
  • Be patient when testing capacitors, as their measurement can take longer than other components.

9. Warranty & Support

For support or warranty inquiries, please contact the manufacturer or their authorized representative:

  • Manufacturer: Taiyuan xinteer trading co., ltd.
  • Manufacturer Address: Room 702, Floor 7, Unit 1, Building 3, Fenhewan, No.8 Yangguang Road, Yijing Street, Jinyuan District, Taiyuan City, Shanxi Province, Code: 030000
  • EU Authorized Representative: Prolinx GmbH
  • EU Representative Address: Duesseldorf / Brehmstr.56, Germany
  • EU Representative Contact: eu@eulinx.eu / +49 21131054698

A detailed user manual in PDF format is available for download: View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.