GGBEE RF 433MHz DC 12V

Contents

GGBEE RF433Mhz Wireless Remote Control Switch User Manual

Model: RF 433MHz DC 12V

1. Introduction

This product employs the latest high-end intelligent microprocessor control technology, comprising advanced components such as microprocessor chips, relays, and wireless receiver modules. Designed for garage door control, lighting control, remote-controlled curtains, and access control systems, it features a compact size, easy installation, and reliable operation.

A detailed user manual is also available in PDF format for download: User Manual (PDF)

2. Safety Information

  • Ensure all power supplies are disconnected before performing any wiring or installation.
  • Do not expose the device to moisture or extreme temperatures.
  • Handle electronic components with care to avoid damage.
  • This device is intended for low-voltage DC applications. Do not connect directly to high-voltage AC without proper conversion.

3. Package Contents

Depending on your selected variant, your package may include:

  • RF433Mhz Receiver Module (DC 12V)
  • RF433Mhz Remote Control(s) (with battery: CR2016 Lithium Battery 3V)
  • Protective Casing for Receiver (optional, may be pre-installed)
Main product image showing the remote control and receiver module.

Figure 3.1: Remote Control and Receiver Module

4. Product Overview

The system consists of a compact receiver module and a handheld remote control. The receiver module features a learning button for pairing and mode selection, and terminals for power input and load connection.

Receiver board with labeled components: Learning Code Keys, Flame Retardant Terminals, Superheterodyne reception, Soft Rubber Keys.

Figure 4.1: Receiver Module Components

Video 4.1: Demonstration of pairing, operating modes, and code clearing.

5. Setup and Installation

5.1 Wiring Diagrams

Important: For your personal safety, operate with all power supplies disconnected before wiring.

Control DC wiring diagram showing DC12V Power Input (+ and -) connected to the receiver, and Load connected to NC, COM, NO terminals.

Figure 5.1: Control DC Wiring Diagram

For DC loads, connect the DC12V power input to the receiver's + and - terminals. Connect your DC load to the NC (Normally Closed), COM (Common), and NO (Normally Open) terminals as required by your application.

Control AC wiring diagram showing DC12V Power Input (+ and -) connected to the receiver, and AC220V Power Input (L and N) connected to the Load via NC, COM, NO terminals.

Figure 5.2: Control AC Wiring Diagram

For AC loads, connect the DC12V power input to the receiver's + and - terminals. Connect your AC power (L and N) and AC load to the NC, COM, and NO terminals. Ensure proper isolation and safety measures when working with AC power.

5.2 Pairing Method (Pattern Matching)

The receiver supports multiple operating modes. Follow the instructions below to pair your remote control in the desired mode.

Illustration of pairing method showing remote and receiver.

Figure 5.3: Pairing Method Overview

5.2.1 Momentary Mode

(Push button, relay connects; release button, relay disconnects)

  1. Briefly press the learning button on the receiver module once. The LED indicator will flash once.
  2. Wait for a moment until the LED turns off, indicating it's in learning state.
  3. Press the desired button on your remote control. The receiver's LED indicator will flash then turn off.
  4. After 3 seconds, the LED indicator will turn on again, confirming successful learning.

5.2.2 Self-locking (Toggle) Mode

(Push button once, relay connects; push again, relay disconnects)

  1. Press the learning button on the receiver module twice in quick succession. The LED indicator will flash twice.
  2. Wait for a moment until the LED turns off, indicating it's in learning state.
  3. Press the desired button on your remote control. The receiver's LED indicator will flash then turn off.
  4. After 3 seconds, the LED indicator will turn on again, confirming successful learning.

5.2.3 Interlock (Latching) Mode

(Push remote button A, relay connects; push remote button B, relay disconnects)

  1. Press the learning button on the receiver module three times in quick succession. The LED indicator will flash three times.
  2. Wait for a moment until the LED turns off, indicating it's in learning state.
  3. Press the first button (e.g., 'A') on your remote control (for ON). The LED will flash 5 times.
  4. Press the second button (e.g., 'B') on your remote control (for OFF). The LED will flash 5 times.
  5. After 3 seconds, the LED indicator will turn on again, confirming successful learning.

5.2.4 Time Delay Mode

(Push remote button, relay connects; after a set delay, relay disconnects automatically)

  1. For 5-second delay: Press the learning button on the receiver module four times. The LED will flash four times.
  2. For 10-second delay: Press the learning button on the receiver module five times. The LED will flash five times.
  3. For 15-second delay: Press the learning button on the receiver module six times. The LED will flash six times.
  4. For 20-second delay: Press the learning button on the receiver module seven times. The LED will flash seven times.
  5. After selecting the delay, the LED indicator will turn off, indicating it's in learning state.
  6. Press the desired button on your remote control. The LED will flash and then turn off.
  7. After 3 seconds, the LED indicator will turn on again, confirming successful learning.

Note:

  • The system can store up to 25 remote controls. If more than 25 remotes are learned, the initial remote controls will be lost.

5.3 Clearing the Code

To clear all previously paired remote controls from the receiver:

  1. Ensure the receiver is powered on.
  2. Press and hold the learning button on the receiver module for approximately 5 seconds.
  3. The LED indicator will flash 5 times and then turn off, indicating that all previously paired remote controls have been cleared.
  4. After clearing, none of the old remote controls will be able to control the receiver.

6. Operating Modes

Once paired, the receiver operates according to the mode it was learned in:

  • Momentary Mode: The relay is active only while the remote button is pressed. Releasing the button deactivates the relay.
  • Self-locking (Toggle) Mode: Pressing the remote button once activates the relay. Pressing the same button again deactivates the relay.
  • Interlock (Latching) Mode: Pressing one remote button (e.g., 'A') activates the relay. Pressing another remote button (e.g., 'B') deactivates the relay. Only one relay can be active at a time in multi-channel systems.
  • Time Delay Mode: Pressing the remote button activates the relay. The relay remains active for the pre-set duration (5s, 10s, 15s, or 20s) after the button is released, then automatically deactivates.

7. Maintenance

  • Keep the device clean and free from dust.
  • Avoid exposing the device to water or high humidity.
  • Do not attempt to repair the device yourself if it is damaged; contact support.
  • Replace the remote control battery (CR2016) when its range decreases or it stops responding.

8. Troubleshooting

  • Device not responding: Check power connections to the receiver. Ensure the remote control battery is not depleted. Re-pair the remote control if necessary.
  • Short range: Replace the remote control battery. Ensure there are no significant obstructions between the remote and receiver.
  • Incorrect operation mode: Clear all codes and re-pair the remote control in the desired mode.
  • LED not flashing during pairing: Ensure the learning button is pressed correctly and the receiver is powered.

9. Specifications

9.1 Receiver Module Specifications

ParameterValue
Operating VoltageDC 12V (6V/9V/24V available upon request)
Standby Current≤10mA
Operating Temperature-40°C to +80°C
Receiver Sensitivity≥-100dB
Operating Frequency315MHz, 433.92MHz (Other frequencies available upon request)
Output Current (Max Load)≤10A (110W)
Dimensions55mm x 32mm x 16mm
Support Encoding FormatEV1527
Wiring MethodNC COM NO
Operating ModesMomentary, Toggle, Latching, Time Delay (5s, 10s, 15s)

9.2 Remote Control Specifications

ParameterValue
Operating RF Frequency433MHz
Coded System1527 Learning Code
Working VoltageDC 3V
Working Current<25mA
Transmitting Power10mW
Wireless Operating Distance50m (Free Space)
Transmission Rate50 ~ 60KHz
Frequency Deviation±0.2MHz
Battery TypeCR2016 Lithium Battery 3V

10. User Tips

No specific user tips are available from reviews or Q&A at this time. Always ensure proper wiring and test functionality in a safe environment before final installation.

11. Warranty & Support

For warranty information and technical support, please refer to the seller's policies or contact the point of purchase. Keep your proof of purchase for any warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.